Aerus LAUNDRY PRO Bedienungsanleitung

CAUTION: READ MANUAL CAREFULLY FOR PROPER USE AND OPERATION.

USER’S MANUAL

OWNER’S MANUAL

GENERAL INFORMATION

CONTENTS

General Information . . . . . . . . . . . . . 2

Use & Safety Considerations . . . . . . . . . . 3

Installation Requirements . . . . . . . . . . . 4

Cabinet Features . . . . . . . . . . . . . . .4

Before You Start . . . . . . . . . . . . . . . 5

Removing Cover . . . . . . . . . . . . . . . 5

Installation of Wall Anchors . . . . . . . . . . 6

Hose Installation . . . . . . . . . . . . . . . 7

System Set Up. . . . . . . . . . . . . . . .9

Before Washing Clothes . . . . . . . . . . . 10

Using Your Laundry Pro . . . . . . . . . . . 10

Washers Requiring Hot & Cold Water . . . . . 11

Status Indications . . . . . . . . . . . . . 12

Frequently Asked Questions . . . . . . . . . 13

Installation Problems . . . . . . . . . . . . 13

Warranty Information . . . . . . . . . . . . 14

Declaration of Conformity . . . . . . . . . . 15

PRODUCT OVERVIEW

Laundry Pro is designed to work in conjunction with your washing

machine, using cold water, and ActivePure to clean clothes. As

your washer begins to ll, Laundry Pro will turn on.

Laundry Pro is equipped with an internal leak sensor.

See page 12 for more details.

Welcome to the Aerus®World of

E X C E L L E N C E !

There’s a smart new approach to laundry that’s based on earth-friendly

science and technology. Laundry Pro, designed and made in America,

eliminates the need for hot water, detergents, fabric softeners and bleaches,

thereby allowing it to pay for itself over and over again.

Laundry Pro is easy to install, and is used on both standard and high

efciency washers. It is intended to work with residential clothes washers

and is for use by anyone interested in an economical, earth-friendly

alternative to the typical detergents and chemicals currently available,

without modifying existing appliances, electrical systems, or plumbing.

Laundry Pro uses a variation of the technology originally developed for use

in the International Space Station and is recognized as a Certied Space

Technology by the Space Foundation.

FILL IN AND SAVE

The location of the serial number is on the back panel of the water

unit, below the water line connection. Write it here and retain for

future reference.

Model No. ___________________________________________________________

Serial No. ___________________________________________________________

Date of Purchase _____________________________________________________

Aerus®Ofﬁce Phone No._______________________________________________

_____________________________________________________________________

Aerus™Ofﬁce Address_________________________________________________

_____________________________________________________________________

Sales Representative__________________________________________________

_____________________________________________________________________

SPECIFICATIONS

AC/DC Adaptor:

• AC in: 100 - 240V ~ 50/60 Hz .45A

• DC out: 12V

Power Consumption:

•.4W AC (standby mode)

• 1.3W AC operating

Water Pressure:

• Minimum 20 psi to 75 psi maximum

Water Temperature:

• Use cold water only (do not use hot water)

Operating Environment:

• 50˚F - 100˚F ( 10˚C - 37.8˚C) Humidity 20% ~ 70%

Dimensions:

• 17.25 in. x 9.6 in. x 4.05 in.

• 438 mm x 244 mm x 103 mm

Weight:

• 4.486 pounds

• 2.04 kg

• Forindooruseonly.

• Donotoperateunitwithcoverremoved.

• Disconnectallpowerbeforeservicing.

• Donotuseanextensioncordorotheradapterwiththisappliance.

• Thisapplianceisnotrecommendedforusewithhighironorsedimentcontentwater.

If your water has a high iron or sediment content, consult a water ltration expert for

available options.

• Maximumdynamicwaterinletpressureis75psi.

• UsetheincludednewhosewhenconnectingtheLaundryProunittoyourwashing

machine. You should replace any washing machine hose that is more than 3 years old.

• Donotleaveyourhotwaterhosedisconnected.

• DonotcleanyourLaundryProwithharshchemicals,abrasives,orcleansers.Usea

soft cloth dampened with water.

• DonotmounttheLaundryProunitvertically,belowthetopofthewasheroratan

angle. Improper mounting may not allow the unit to function properly and void your

warranty. See page 6 for correct mounting instructions.

• LaundryProisdesignedfornormalresidentialuseonly.Useinacommercialornon-

residential setting will void your warranty.

USE & SAFETY CONSIDERATIONS

IMPORTANT SAFETY PRECAUTIONS

• Topreventunnecessaryriskofre,electricalshock,orpersonalinjury,allwiringmust

bedoneinaccordancewiththeNationalElectricalCodeANSI/FNPA,No.70-Latest

Revision and local codes and ordinances. It is the personal responsibility and obligation

of the appliance owner to provide adequate electrical service for this appliance.

We have provided

important safety warnings

in this manual and on your

appliance. Always read and

obey all safety messages.

Safety warnings in this

manual are dened

as follows:

WARNING:

Electrical shock hazard.

You can be killed or seriously

injured if you don’t follow

instructions.

CAUTION:

Damagetoyourappliance

or the surrounding area can

occur if you don’t follow

instructions.

DANGER:

Deathorseriousinjurycan

occur if instructions are not

followed immediately.

NOTE:

This information is included

to aid in installation and use

of this appliance.

NOTE:

YourLaundryProUnitwasfactorytested.Itisnormalforsomeresidualwatertostill

remain in the unit as a result of these tests.

Water treated by your Laundry Pro unit is intended for clothes washing only and is

NOT approved for any internal consumption such as drinking, bathing, brushing teeth,

etc.DONOTdrink,ingest,orinternallyconsumethewaterfromyourLaundryProunit

orwashingmachine.DONOTprovidewaterfromyourLaundryProtoyourpetsor

other animals.

CAUTION:

ELECTRICAL REQUIREMENTS

100-240Volt50/60Hz5AMP(minimum)FuseorCircuitBreaker.

LaundryProisequippedwithanACtoDCpowersupply.

NEVER USE AN EXTENSION CORD.

WATER REQUIREMENTS

Adynamicwaterpressureof20to75psiisrequiredtocorrectly

operate your Laundry Pro. See Cautions below.

CABINET FEATURES

WATER

OUTLET

WATER

INLET

INSTALLATION REQUIREMENTS

LOCATION CONSIDERATIONS

It is recommended the Laundry Pro never be installed in areas

where water may freeze since the unit will always maintain some

water in the unit, the water valve, and hose areas. This can cause

damage to internal components. It is also recommended to avoid

installation in areas of high humidity, as it can effect the operation

of the unit.

17.25” (438 mm)

9.6” (244 mm)

4.05” (103 mm)

Incoming water pressure must be less than 75 psi. If your household water

pressure is greater than 75 psi, you must install an in-line pressure reducer before

installing Laundry Pro. Failure to follow these instructions may result in water

leakage, property damage, personal injury, and may void your warranty. Water

pressure of 20 to 75 psi is required to correctly operate your Laundry Pro. Low water

pressure may prevent your unit from operating properly and/or cause a failure in your

washing machine’s water valve.

The washer’s water valve may also not shut off completely. Check the documentation

supplied with your washing machine for exact speciﬁcations. Your washing machine

and cold water faucet must be within 4 feet of the right side of the unit to use the inlet

hose provided with your Laundry Pro.

TO AVOID THE POSSIBILITY OF WATER DAMAGE, SHOULD A HOSE LEAK, ALWAYS

HAVE FAUCETS ACCESSIBLE AND TURN OFF FAUCETS WHEN WASHER IS NOT IN

USE.

Water quality may affect the performance of your Laundry Pro unit.If you have water

quality concerns such as high iron content or high chlorine content, consult a water

ﬁltration expert. This system is designed for use on potable water systems only.

CAUTION:

BEFORE YOU START

REMOVING COVER

• Remove your new Laundry Pro from its packaging.

• Inspect the unit for any signs of shipping damage.

NOTE:

Your Laundry Pro unit was factory tested. It is normal for some

residual water to still remain in the unit as a result of these tests.

Screws

 Removethetwo(2)cover

screws located on the bottom

of the unit.

 Removethetwo(2)screws

(notshown)alongthetop

of the Laundry Pro.

To remove the cover, pull the

top away from the unit, then lift

off the cover.

This appliance must be installed in a level,

horizontal conguration as shown. Do not install

the unit vertically, below the top of the washer

or at an angle. Failure to follow these instructions

may prevent the internal moisture sensor from

operating properly.

CAUTION:

INSTALLATION OF WALL ANCHORS OR SCREWS

A. If using supplied wall anchors, drill two 3/16” diameter holes.

Place two wall anchors into the wall. Install two supplied

screws and tighten until almost all the way in.

B. If mounting to wall studs, drill two 3/32” diameter holes

approximately 1” deep. Install two supplied screws and

tighten until almost all the way in.

16” OC

Keyholes

NOTE: Washing machine and cold water faucet must

be within 4 feet of the right side of unit.

Level and place the Laundry Pro to the wall

andmarkwherethetwo(2)keyholesareon

each side with a pencil.

Screws (not shown)

Position the keyholes of the Laundry Pro onto the screws

(notshown).Finishtighteningscrewsenoughtosecurely

mount unit, but still allowing it to be removed from wall.

Remove unit from wall.

HOSE INSTALLATION

Turn the cold water

off by shutting

off the cold water

faucet.

NOTE: To help prevent water spray when

disconnecting hoses, you can relieve pressure

in the water line by momentarily starting your

washing machine.

NOTE: To ease hose installation and prevent cross threading,

connect hose prior to mounting unit on wall.

NOTE: Remove the two black caps from the hose

connections before installing hoses.

Remove the cold

water hose from the

cold water inlet on the

back of your washing

machine. Leave hot

water hose attached.

When connecting hoses to your Laundry Pro hand start the hose

connector(s)Usingadjustablepliersnishtighteninghoseconnector(s).

Donotremoveordisconnectthehotwaterlinefromyourwashing

machine or water valve.

CAUTION:

Return the Laundry Pro cover to its

original position, tting the bottom in

place and tipping upward.

 Securewithtwo(2)screws

(notshown)alongthetopedge.

 Putthetwo(2)remainingscrewsalong

the bottom edge and tighten.

REINSTALL THE COVER

HOSE INSTALLATION

Screws

1 2

CONNECTING POWER ADAPTOR

1. Insert the provided power cord into the

POWER IN socket located on the back of the unit.

(Note: Do not plug the adaptor into the wall socket

until installation is complete. See page 9.)

2. Align mounting screws with mounting keyholes

on back of unit and place unit on wall.

DonotuseanyAC/DCadaptorotherthantheonesuppliedwithyourLaundryProorAerusreplacement

AC/DCadaptor(item#49700).Failuretofollowtheseinstructionsmayvoidyourwarrantyand/orresultin

damage to your unit, re, or electrical shock.

CAUTION:

TheAC/DCadaptor

is designed to work

worldwide. The

electrical plug may be

removed and *other

types added depending

on the country electrical

requirements.

HOSE INSTALLATION

Connect the hose from the cold

water inlet on your washing

machine to the INLET connection

on your Laundry Pro.

Finally, connect the new hose

to the cold water inlet on your

washing machine.

Connect the new hose provided

with your Laundry Pro to the

waterOUTLETconnectoron

your Laundry Pro unit.

NOTE: To ease hose installation and prevent cross threading,

connect hoses prior to mounting unit on wall.

NOTE: If your existing hose is more than 3 years old, it is our recommendation that you replace

itwiththeoptionalstainlesssteelhose(item#49701).

*Other types are optional. Not included.

3 4 5

Turn on the cold

water valve.

SYSTEM SET UP

Check all hoses to ensure no water

is leaking. Tighten if necessary.

Start your washer.

The status light should illuminate blue.

NOTE: Your Laundry Pro will automatically turn on and off as your washing machine starts, and stops.

ElectricalShockHazard.Whenworkingwithelectrical

connections, the appliance and surrounding area should

be clean and dry of any standing water. Failure to follow

these instructions can result in death, re, or

electrical shock.

WARNING:

ElectricalShockHazard.Donouseanextensioncord.

Failure to follow these instructions can result in death,

re, or electrical shock.

WARNING:

Plug power cord into the wall outlet of your

home’s electrical power system. See page 4

for electrical requirements.

Status Indicator Lights

BEFORE WASHING CLOTHES

IF YOUR WASHING MACHINE IS NOT NEW you will need to perform this

procedure to help remove any detergent buildup that may contaminate

your clothing.

1. Donotputclothesinthewasheratthistime.

Set your machine to its largest load setting, cold water only.

2. Start the washer and let it run through every cycle.

3. Once it has nished, repeat Steps 1 and 2 three more times.

Dependingontheageandseverityofdetergentbuildup,

it may be necessary to perform Step 3 several times.

NOTE: If you have a front loading washer, odors can develop due to

stagnant water left inside. If musty odors develop it may be necessary

to run a commercially available cleaner made especially for front loading

washers to eliminate such odors.

CAUTION:

To avoid the possibility of water damage, should a hose leak, always have

faucets accessible and turn off faucets when washer is not in use.

IF YOUR WASHING MACHINE IS NEW, skip this section and

continue below.

BEFORE USING YOUR LAUNDRY PRO FOR THE FIRST TIME

USING YOUR LAUNDRY PRO

DETERGENT AND FABRIC SOFTENER

Youmaychoosetocontinuetousedetergentand/orfabricsoftenersifdesired.However,to

completely experience all the benets of your new Laundry Pro, we recommend washing using

nothingbutcoldwater.NEVERapplydetergentdirectlytodryclothes.Allowwashertoll,thenadd

detergent to prevent staining on clothes.

COLD HOT

NORMAL OPERATION

UsingyourLaundryProisassimpleasturningonthewashingmachine.

LaundryProisdesignedtousetheCOLD/COLDsettingofyourwashingmachine.

HEAVY STAINS

For heavy stains, pre-treat area, apply pre-treater, rub gently and let stand for several minutes.

Wash as normal.

Inhaltsverzeichnis

Sprachen:

Andere Aerus Waschmaschine Handbücher

Aerus

Aerus Beyond LAUNDRY PRO 2.0 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

LAUNDRY JET

LAUNDRY JET Plus Bedienungsanleitung

LG WKGX301H A Series Bedienungsanleitung

Kenmore

Kenmore Kenmore 27" Wide LAUNDRY CENTER Washer -... Bedienungsanleitung

LG WK X30 Series Bedienungsanleitung

Frigidaire

Frigidaire GLEH164DS1 Administratorhandbuch

Frigidaire

Frigidaire GLEH1642DS0 Administratorhandbuch

AEG

AEG LAVATHERM 65280AC Bedienungsanleitung

Samsung

Samsung WF0500NXWG Bedienungsanleitung

Whirlpool

Whirlpool WVP5000SQ0 Bedienungsanleitung

Whirlpool

Whirlpool XVP8600TB0 Bedienungsanleitung

Frigidaire

Frigidaire MEX731CFS2 Bedienungsanleitung

GE Spacemaker WSM2700 Bedienungsanleitung

GE Spacemaker WSM2780 Bedienungsanleitung

Asko

Asko Washer/Dryer Combination Laundry System Bedienungsanleitung

Frigidaire

Frigidaire FLCE752CAW Betriebsanleitung

Mustee

Mustee UTILATUB 17F Bedienungsanleitung

Whirlpool

Whirlpool XVP9000TA0 Bedienungsanleitung

GE Spacemaker WSM2780 Bedienungsanleitung