AGA FFD Bedienungsanleitung
Cooking
Cooking
Guide
Guide
included
included
inside
inside
09/07 EINS 511612
PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS APPLIANCE
REMEMBER, when replacing a part on this appliance, use only spare parts that
you can be assured conform to the safety and performance specification that we
require. Do not use reconditioned or copy parts that have not been clearly
authorised by Aga
For use in GB and IE
Comprising
Installation & Users
Instructions
&
Cooking
Guide
COMPANION (FFD)
(with Gas Hob)
OWNERS MANUAL
SECTION PAGE
INSTALLATION SECTION 3
INSTALLATION 4
TECHNICAL DATA 5
ELECTRICAL CONTROLS 6
LOCATION 7
PRODUCT DIMENSIONS 8
CONNECTING TO GAS 9
PRESSURE TESTING 10
USERS GUIDE 11
GENERAL INFORMATION 12
HEALTH & SAFETY 13
PRODUCT VIEW 14
CONTROL PANEL 15
GAS HOTPLATE 16
THE GRILL AND THE OVENS 17
OVEN COOKING GUIDE 18 - 22
CLEANING AND CARING FOR YOUR COOKER 23 - 25
SERVICING 26
WIRING DIAGRAM 27
2
CONTENTS
Installation
Section
3
INSTALLATION
WARNING: THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE
REGULATIONS IN FORCE AND ONLY USED IN A WELL VENTILATED SPACE. READ THE
INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE.
PRIOR TO INSTALLATION, ENSURE THAT THE LOCAL DISTRIBUTION CONDITIONS
(NATURE OF GAS AND GAS PRESSURE) AND THE ADJUSTMENTS OF THE APPLIANCE
ARE COMPATIBLE.
THE ADJUSTMENT CONDITIONS FOR THIS APPLIANCE ARE STATED ON THE DATA
PLATE WHICH IS SITUATED IN THE CENTRE VENT SLOT NEAR THE BASE OF THE
FRONT PLATE
This appliance is not connected to a combustion products evacuation device. It shall be installed
and connected in accordance with current installation regulations. Particular attention shall be
given to the relevant requirements regarding ventilation. (B.S. 5440 Part 2: 1989)..
It should be in accordance also with any relevant requirements of the Gas Region and Local
Authority.
In your own interest, and that of safety to comply with the law, all gas appliances must be
installed by a competent person. Failure to install appliances correctly could lead to prosecution.
On completion, test the gas installation for soundness.
WARNING: THIS APPLIANCE MUST BE EARTHED
The appliance is designed for the voltage stated on the data plate.
The Companion is supplied from the manufacturers in a fully assembled and tested condition.
4
HOTPLATE
NATURAL GAS G20 - (APPLIANCE CATEGORY I2H)
R.H.F. L.H.R. R.H.R. L.H.F.
BURNER TYPE ULTRA-RAPID RAPID SEMI-RAPID SEMI-RAPID
MAXIMUM HEAT 3.5 kW 3.0 kW 1.75 kW 1.75 kW
INPUT
INJECTOR MARKING 130 116 097 097
PRESSURE POINT POSITION:REAR LH SIDE OF APPLIANCE AT HOTPLATE LEVEL
PRESSURE SETTING: 20mbar
BURNER IGNITION: H.T. SPARK
PROPANE G31 - (APPLIANCE CATEGORY I3+)
R.H.F. L.H.R. R.H.R. L.H.F.
BURNER TYPE ULTRA-RAPID RAPID SEMI-RAPID SEMI-RAPID
MAXIMUM HEAT 3.5 kW 3.0 kW 1.75 kW 1.75 kW
INPUT (250g/h) (214g/h) (125g/h) (125g/h)
(0.50 l/h) (0.42 l/h) (0.25 l/h) (0.25 l/h)
INJECTOR MARKING 95 85 65 65
PRESSURE POINT POSITION:REAR LH SIDE OF APPLIANCE AT HOTPLATE LEVEL
PRESSURE SETTING: G30: 28-30 mbar G31 - 37 mbar
BURNER IGNITION: H.T. SPARK
ELECTRIC GRILL AND OVENS
GRILL ELEMENT - POWER RATING 2 x 0.95 kW
TOP OVEN - POWER RATING 1.4kW
LOWER OVEN (FANNED) - 1.75kW
TECHNICAL DATA
5
ELECTRICAL CONTROLS
Electrical connections are located at the back of the appliance
Refer to Figs. 1A for wiring connection to the appliance.
Remember that an excess of cable length is required for the possible withdrawal of the cooker.
Always double check connections and ensure terminals are fully tightened and the cable is
secured to the cable clamp.
THE ISOLATOR SHOULD NOT BE POSITIONED IMMEDIATELY ABOVE THE COMPANION
COOKER, BUT MUST BE SITED WITHIN 2 METRES OF THE APPLIANCE.
The Companion requires a 30 amp power supply fitted in conjunction with a double pole isolator
with a minimum contact clearance of 3mm and be connected to the mains with a minimum 4mm2
cable to comply with the latest editions of the local and national wiring regulations.
FIG. 1A
DESN 513370
DESN 513372
6
MINIMUM 4mm2AND MUST COMPLY WITH THE LATEST EDITIONS OF THE LOCAL
AND NATIONAL WIRING REGULATIONS
REMOVE COVER (4
SCREWS) TO GAIN ACCESS
TO THE MAINS TERMINAL
7
This is a CLASS1, type X appliance.
Any side wall above the hob on either side shall be greater than 60mm horizontally from the
cooker only when adjacent to combustible material (Fig. 2).
Surfaces over the top of the cooker must not be closer than 650mm.
The vent slots in the back of the top plate must not be obstructed.
INSTALLATION/LEVELLING
The Aga Companion is designed to stand on a flat and level surface, however, any unevenness
may be overcome by packing under the corners of the plinth with a suitable non combustible
material, (up to 2-3mm).
LOCATION
PRODUCT DIMENSIONS
8
Fig. .2 DESN 511616
60mm*
595mm
910mm
600mm
680mm
1080mm
948mm
APPLIANCE CAN BE CLOSE
FITTED TO KITCHEN UNITS UP
TO WORK TOP HEIGHT.
116mm
* WHEN ADJACENT TO COMBUSTIBLE MATERIAL
This cooker can be installed with an approved appliance flexible connection. Supply piping
should not be less than R 1/2 (1/2” BSP). Connection is made to the R 1/2 (1/2” BSP) female
threaded entry in the inlet block located just below the hotplate level on the rear left hand side of
the cooker.
Check for gas soundness after connecting the gas supply.
The gas bayonet connector must be fitted in the shaded area indicated in Fig. 3 . Take into
account that it must be possible to pull the cooker forward sufficiently. Ensure flexible hose is not
trapped between electrics cover and rear wall. Ensure hose is routed within shaded area, and
away from shielded oven vent.
The flexible hose must be in accordance with the relevant standards.
NOTE: FOR L.P.G. APPLIANCE
The flexible hose must be suitable for use with Propane gas, capable of 70°C temperature rise,
and carry a red stripe, band or label. If in doubt contact your supplier.
9
CONNECTING TO GAS
Fig. 3 DESN 511751
480
390
200
460
573
279
558
TERMINAL BLOCK
COVER
The pressure test point is situated at the rear left hand side of the appliance just below hotplate
level.
Remove screw from pressure test nipple. Fit the pressure gauge onto the pressure test nipple.
Place one of the burner heads and burner cap into position on the hotplate. Light this burner by
pushing in the appropriate control knob, and turning it anti-clockwise to the full on position.
For Natural Gas appliance, the pressure should be 20mbar (8 inches water gauge).
For LPG appliance the pressure should be Propane 37mbar and Butane 28-30mbar.
Turn off the tap, disconnect the pressure gauge and refit pressure test screw to pressure test
nipple.
Check for gas soundness.
10
PRESSURE TESTING
Andere Handbücher für FFD
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere AGA Kochfeld Handbücher
AGA
AGA Six Four Series Bedienungsanleitung
AGA
AGA DC3 Bedienungsanleitung
AGA
AGA SIX-FOUR Series Bedienungsanleitung
AGA
AGA Companion Bedienungsanleitung
AGA
AGA TC3 Bedienungsanleitung
AGA
AGA TC/DC Gebrauchs- und Pflegehandbuch
AGA
AGA eR7 Series Bedienungsanleitung
AGA
AGA FFD Bedienungsanleitung
AGA
AGA ELECTRIC HOB UNIT Bedienungsanleitung
AGA
AGA CITY60 CONTEMPORARY Bedienungsanleitung
AGA
AGA Six Four Series Bedienungsanleitung
AGA
AGA 60 Bedienungsanleitung
AGA
AGA 4-oven Bedienungsanleitung
AGA
AGA AG1M251730 Bedienungsanleitung
AGA
AGA 7 Series Bedienungsanleitung
AGA
AGA TC MODULE (FFD)(with Gas Hob) Bedienungsanleitung
AGA
AGA LPRT 517725 Bedienungsanleitung
AGA
AGA Masterchef II Ceramic Bedienungsanleitung
AGA
AGA 60 Bedienungsanleitung
