AGI WESTFIELD WR Series Bedienungsanleitung

Part Number: 30252 R1

Revised: 24/1/12

Read this manual before using product. Failure

to follow instructions and safety precautions can

result in serious injury, death, or property

damage. Keep manual for future reference.

WR MD GRAIN AUGER

WR60 & WR80

OPERATION & ASSEMBLY MANUAL

WR MD Augers covered in this

manual:

60-26, 60-31, 60-36, 60-41

80-26, 80-31, 80-36, 80-41

This product has been designed and constructed according to general engineering

standardsa. Other local regulations may apply and must be followed by the operator.

We strongly recommend that all personnel associated with this equipment be trained

in the correct operational and safety procedures required for this product. Periodic

reviews of this manual with all employees should be standard practice. For your

convenience, we include this sign-off sheet so you can record your periodic reviews.

a. Standards include organizations such as the American Society of Agricultural and Biological Engineers,

American National Standards Institute, Canadian Standards Association, International Organization for

Standardization, and/or others.

Date Employee Signature Employer Signature

TABLE OF CONTENTS

WESTFIELD INDUSTRIES - WR MD GRAIN AUGER

WR60 & WR80

30252 R1 3

1. Introduction .......................................................................................................................... 5

2. Safety First............................................................................................................................ 7

2.1. General Safety ......................................................................................................... 8

2.2. Assembly Safety....................................................................................................... 9

2.3. Operation Safety ...................................................................................................... 9

2.4. Transport & Placement Safety ............................................................................... 11

2.5. Maintenance Safety................................................................................................ 12

2.6. Electric Motor Safety .............................................................................................. 12

2.7. Gas Engine Safety ................................................................................................. 12

2.8. Battery Safety......................................................................................................... 12

2.9. Safety Decals ......................................................................................................... 13

2.9.1. Decal Installation ...................................................................................... 13

2.9.2. Safety Decal Locations............................................................................. 13

3. Assembly ............................................................................................................................ 15

3.1. Tubes & Flighting ................................................................................................... 15

3.2. Track Shoe & Track Stop ....................................................................................... 17

3.3. Intake Hitch ............................................................................................................ 18

3.4. Multi-Stage Driveshaft ............................................................................................ 18

3.5. Driveshaft Shield .................................................................................................... 19

3.6. Upper Housing Lubrication..................................................................................... 19

3.7. Transport Undercarriage ........................................................................................ 20

3.8. Winch & Lift cable................................................................................................... 22

3.8.1. Winch Handle ........................................................................................... 23

3.9. Motor Drive............................................................................................................. 23

3.10. Plastic Manual Holder .......................................................................................... 27

3.11. Model Decal Placement ....................................................................................... 28

4. Transport & Placement ...................................................................................................... 29

4.1. Transport Procedure .............................................................................................. 29

4.2. Placement Procedure............................................................................................. 30

5. Operation ............................................................................................................................ 33

5.1. Pre-Operational Checklist ...................................................................................... 33

5.2. Auger Drive & Lockout Procedure.......................................................................... 33

5.3. Operating Procedure .............................................................................................. 34

5.3.1. Start-Up & Break-In .................................................................................. 34

5.3.2. Operating With A Full Load ...................................................................... 35

5.3.3. Shutdown.................................................................................................. 35

5.3.4. Lowering & Completion ............................................................................ 36

6. Maintenance & Storage...................................................................................................... 37

6.1. General Maintenance Procedures.......................................................................... 37

6.2. General Storage Procedures.................................................................................. 39

TABLE OF CONTENTS

WESTFIELD INDUSTRIES - WR MD GRAIN AUGER

WR60 & WR80

430252 R1

7. Troubleshooting ................................................................................................................. 41

Warranty.................................................................................................................................. 43

WESTFIELD INDUSTRIES - WR MD GRAIN AUGER 1. INTRODUCTION

WR60 & WR80

30252 R1 5

1. Introduction

Thank you for purchasing a Westfield Industries grain auger. Before using,

please read this manual and understand the various features of the equipment

and precautions for efficient and safe operation.

Keep this manual handy for frequent reference and to review with new

personnel. A sign-off form is supplied on the inside front cover to record your

safety reviews. Call your local distributor or dealer if you need assistance or

additional information.

This manual should be regarded as part of the equipment. Suppliers of both new

and second-hand equipment are advised to retain documentary evidence that

this manual was provided with the machine.

Serial Number:

If one long tube, serial number is found on the right, in the

middle of the tube. If more than one tube, number is on the

right, at the top of the lower tube.

1. INTRODUCTION WESTFIELD INDUSTRIES - WR MD GRAIN AUGER

WR60 & WR80

630252 R1

WESTFIELD INDUSTRIES - WR MD GRAIN AUGER 2. SAFETY FIRST

WR60 & WR80

30252 R1 7

2. Safety First

The Safety Alert symbol to the left identifies important safety messages on the

product and in the manual. When you see this symbol, be alert to the possibil-

ity of personal injury or death. Follow the instructions in the safety messages.

Why is SAFETY important to you?

Three big reasons:

• Accidents disable and kill.

• Accidents cost.

• Accidents can be avoided.

SIGNAL WORDS

Note the use of the signal words DANGER, WARNING, CAUTION, and NOTICE

with the safety messages. The appropriate signal word for each message has

been selected using the definitions below as a guideline.

The Safety Alert symbol means: “ATTENTION, BE ALERT! YOUR SAFETY IS

INVOLVED”.

DANGER

Indicates an imminently hazardous situation

that, if not avoided, will result in serious injury

or death.

WARNING

Indicates a hazardous situation that, if not

avoided, could result in serious injury or

death.

CAUTION

Indicates a hazardous situation that, if not

avoided, may result in minor or moderate

injury.

NOTICE

Indicates a potentially hazardous situation that, if not

avoided, may result in property damage.

2. SAFETY FIRST WESTFIELD INDUSTRIES - WR MD GRAIN AUGER

2.1. GENERAL SAFETY WR60 & WR80

830252 R1

2.1. GENERAL SAFETY

Important: This general safety section includes instructions that apply to all safety practices.

Any instructions specific to a certain safety practice (e.g., assembly safety), can

be found in the appropriate section. Always read the complete instructional

sections and not just these safety summaries before doing anything with the

equipment.

YOU are responsible for the SAFE use and maintenance of your equipment.

YOU must ensure that you and anyone else who is going to work around the

equipment understands all procedures and related SAFETY information

contained in this manual.

Remember, YOU are the key to safety. Good safety practices not only protect

you, but also the people around you. Make these practices a working part of your

safety program.

• It is the equipment owner and the operator's responsibility to read and under-

stand ALL safety instructions, safety decals, and manuals and follow them

before assembling, operating, or maintaining the equipment. All accidents

can be avoided.

• Equipment owners must give instructions and review the information initially

and annually with all personnel before allowing them to operate this product.

Untrained users/operators expose themselves and bystanders to possible

serious injury or death.

• Use this equipment for its intended purposes only.

• Do not modify the equipment in any way. Unauthorized modification may

impair the function and/or safety, and could affect the life of the equipment.

Any modification to the equipment voids the warranty.

• Do not allow children, spectators, or bystanders within the work area.

• Have a first-aid kit available for use should the need arise, and know how to

use it.

• Provide a fire extinguisher for use in case of an accident. Store in a highly vis-

ible and accessible place.

• Wear appropriate protective gear. This list includes, but

is not limited to:

• a hard hat

•gloves

• protective shoes with slip-resistant soles

• protective goggles

• hearing protection

• dust mask or respirator

• For Powered Equipment: before servicing, adjusting, or repairing powered

equipment, unplug, place all controls in neutral or off position, stop the engine

or motor, remove ignition key or lock out power source, and wait for all mov-

ing parts to stop.

WESTFIELD INDUSTRIES - WR MD GRAIN AUGER 2. SAFETY FIRST

WR60 & WR80 2.2. ASSEMBLY SAFETY

30252 R1 9

• Follow good shop practices:

• keep service area clean and dry

• be sure electrical outlets and tools are properly

grounded

• use adequate light for the job at hand

• Think SAFETY! Work SAFELY!

2.2. ASSEMBLY SAFETY

• Read through the instructions to get to know the sub-assemblies and hard-

ware that make up the equipment.

• Do not take chances with safety. The components are large, heavy, and can

be hard to handle. Always use the proper tools, stands, jacks, and hoists for

the job.

• Read and understand the assembly instructions for the product before pro-

ceeding to assemble the product.

• Always have two or more people assembling the equipment. Because of the

weight, do not attempt assembly alone.

2.3. OPERATION SAFETY

• Have another trained person nearby who can shut down the auger in case of

accident. Always work with a second trained person around augers.

• Do not operate with any of the safety guards removed.

• Keep body, hair, and clothing away from moving parts. Stay away from intake

during operation.

• Inspect lift cable before using auger. Replace if frayed or damaged. Make

sure it is seated properly in the cable sheaves and that cable clamps are

secure.

• Operate auger on level ground free of debris. If ground is uneven, anchor the

auger to prevent tipping or upending.

• Augers are not insulated. Keep away from electrical lines. Electrocution can

occur without direct contact.

• Support the discharge end and/or anchor the intake end before operating to

prevent upending.

• Do not use auger as a hoist.

• Empty auger before raising or lowering.

• Lower auger at completion of operation or when not in use. Auger could drop

rapidly in case of cable break or hydraulic failure (where applicable).

• Lock winch before operating auger.

• Do not grab or touch drive belts during operation for any reason.

2. SAFETY FIRST WESTFIELD INDUSTRIES - WR MD GRAIN AUGER

2.3. OPERATION SAFETY WR60 & WR80

10 30252 R1

Figure 2.1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AGI Rasen- und Gartengeräte Handbücher

AGI

AGI A383 Bedienungsanleitung

AGI

AGI Retro Rocket Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung