Agilent Technologies 66311A Bedienungsanleitung

Errata

Title & Document Type:

Manual Part Number:

Revision Date:

HP References in this Manual

This manual may contain references to HP or Hewlett-Packard. Please note that Hewlett-

Packard's former test and measurement, semiconductor products and chemical analysis

businesses are now part of Agilent Technologies. We have made no changes to this

manual copy. The HP XXXX referred to in this document is now the Agilent XXXX.

For example, model number HP8648A is now model number Agilent 8648A.

About this Manual

We’ve added this manual to the Agilent website in an effort to help you support your

product. This manual provides the best information we could find. It may be incomplete

or contain dated information, and the scan quality may not be ideal. If we find a better

copy in the future, we will add it to the Agilent website.

Support for Your Product

Agilent no longer sells or supports this product. You will find any other available

product information on the Agilent Test & Measurement website:

www.tm.agilent.com

Search for the model number of this product, and the resulting product page will guide

you to any available information. Our service centers may be able to perform calibration

if no repair parts are needed, but no other support from Agilent is available.

66311A Mobile Communications DC Source User's Guide

5962-8272

May 1998

USER’S GUIDE

HP Model 66311A

Mobile Communications

DC Source

For instruments with Serial Numbers:

HP 66311A: US38180101 and up

HP Part No. 5962-8272

Microfiche No. 5962-8273

Printed in USA: May 1998

iii

Safety Summary

The following general safety precautions must be observed during all phases of operation of this instrument.

Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety

standards of design, manufacture, and intended use of the instrument. Hewlett-Packard Company assumes no

liability for the customer's failure to comply with these requirements.

GENERAL

This product is a Safety Class 1 instrument (provided with a protective earth terminal). The protective features of

this product may be impaired if it is used in a manner not specified in the operation instructions.

Any LEDs used in this product are Class 1 LEDs as per IEC 825-1.

ENVIRONMENTAL CONDITIONS

This instrument is intended for indoor use in an installation category II, pollution degree 2 environment. It is

designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to the

specifications tables for the ac mains voltage requirements and ambient operating temperature range.

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage, the correct fuse is installed, and all safety

precautions are taken. Note the instrument's external markings described under "Safety Symbols".

GROUND THE INSTRUMENT

To minimize shock hazard, the instrument chassis and cover must be connected to an electrical ground. The

instrument must be connected to the ac power mains through a grounded power cable, with the ground wire firmly

connected to an electrical ground (safety ground) at the power outlet. Any interruption of the protective (grounding)

conductor or disconnection of the protective earth terminal will cause a potential shock hazard that could result in

personal injury.

ATTENTION: Un circuit de terre continu est essentiel en vue du fonctionnement sécuritaire de l'appareil.

Ne jamais mettre l'appareil en marche lorsque le conducteur de mise … la terre est d‚branch‚.

FUSES

Only fuses with the required rated current, voltage, and specified type (normal blow, time delay, etc.) should be

used. Do not use repaired fuses or short-circuited fuseholders. To do so could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

DO NOT REMOVE THE INSTRUMENT COVER

Operating personnel must not remove instrument covers. Component replacement and internal adjustments must be

made only by qualified service personnel.

Instruments that appear damaged or defective should be made inoperative and secured against unintended

operation until they can be repaired by qualified service personnel.

SAFETY SYMBOLS

Direct current

Alternating current

Both direct and alternating current

Three-phase alternating current

Earth (ground) terminal

Protective earth (ground) terminal

Frame or chassis terminal

Terminal is at earth potential. Used for measurement and control circuits designed to be

operated with one terminal at earth potential.

Terminal for Neutral conductor on permanently installed equipment

Terminal for Line conductor on permanently installed equipment

On (supply)

Off (supply)

Standby (supply). Units with this symbol are not completely disconnected from ac mains when

this switch is off. To completely disconnect the unit from ac mains, either disconnect the power

cord or have a qualified electrician install an external switch.

In position of a bi-stable push control

Out position of a bi-stable push control

Caution, risk of electric shock

Caution, hot surface

Caution (refer to accompanying documents)

WARNING The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the like,

which, if not correctly performed or adhered to, could result in personal injury. Do not proceed

beyond a WARNING sign until the indicated conditions are fully understood and met.

Caution The CAUTION sign denotes a hazard. It calls attention to an operating procedure, or the like,

which, if not correctly performed or adhered to, could result in damage to or destruction of part

or all of the product. Do not proceed beyond a CAUTION sign until the indicated conditions

are fully understood and met.

Declaration Page

DECLARATION OF CONFORMITY

according to ISO/IEC Guide 22 and EN 45014

Manufacturer's Name: Hewlett-Packard Company

Manufacturer's Address: 150 Green Pond Road

Rockaway, New Jersey 07866

U.S.A.

declares that the Product

Product Name: a) Dynamic Measurement DC Source

b) System DC Power Supply

Model Number: a) HP 66311A, 66312A

b) HP 6612B, 6611C, 6612C, 6613C, 6614C

conforms to the following Product Specifications:

Safety: IEC 1010-1:1990+A1(1992) / EN 61010-1:1993

EMC: CISPR 11:1990 / EN 55011:1991 - Group 1 Class B

IEC 801-2:1991 / EN 50082-1:1992 - 4 kV CD, 8 kV AD

IEC 801-3:1984 / EN 50082-1:1992 - 3 V / m

IEC 801-4:1988 / EN 50082-1:1992 - 0.5 kV Signal Lines

1 kV Power Lines

Supplementary Information:

The product herewith complies with the requirements of the Low Voltage Directive

73/23/EEC and the EMC Directive 89/336/EEC and carries the CE-marking accordingly.

New Jersey November, 1997 ______

Location Date Bruce Krueger / Quality Manager

European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH,

Department TRE, Herrenberger Strasse 130, D-71034 Boeblingen (FAX:+49-7031-14-3143)

Acoustic Noise Information

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenläminformationsverordnung vom 18 Januar 1991.

* Schalldruckpegel Lp <70 dB(A)

* Am Arbeitsplatz

* Normaler Betrieb

* Nach EN 27779 (Typprüfung).

Manufacturer's Declaration

This statement is provided to comply with the requirements of the German Sound Emission Directive,

from 18 January 1991.

* Sound Pressure Lp <70 dB(A)

* At Operator Position

* Normal Operation

* According to EN 27779 (Type Test).

Printing History

The edition and current revision of this manual are indicated below. Reprints of this manual containing

minor corrections and updates may have the same printing date. Revised editions are identified by a new

printing date. A revised edition incorporates all new or corrected material since the previous printing

date.

Changes to the manual occurring between revisions are covered by change sheets shipped with the

manual. In some cases, the manual change applies only to specific instruments. Instructions provided on

the change sheet will indicate if a particular change applies only to certain instruments.

This document contains proprietary information protected by copyright. All rights are reserved. No part

of this document may be photocopied, reproduced, or translated into another language without the prior

consent of Hewlett-Packard Company. The information contained in this document is subject to change

without notice.

vii

Table of Contents

Warranty Information ii

Safety Summary iii

Declaration Page v

Acoustic Noise Information vi

Printing History vi

Table of Contents vii

1 - QUICK REFERENCE 1

HP 66311A Mobile Communication DC Source 1

The Front Panel - At a Glance 2

The Rear Panel - At a Glance 3

Instrument Configuration 3

Front Panel Number Entry 4

Front Panel Annunciators 5

Immediate Action Keys 5

Front Panel Menus - At a Glance 6

SCPI Programming Commands - At a Glance 7

2 - GENERAL INFORMATION 9

Document Orientation 9

Safety Considerations 10

Options and Accessories 10

Description 11

Capabilities 11

Front Panel Controls 11

Remote Programming 12

Output Characteristic 12

3 - INSTALLATION 15

Installation and Operating Checklist 15

Inspection 16

Damage 16

Packaging Material 16

Items Supplied 16

Cleaning 16

Location 17

Bench Operation 17

Rack Mounting 17

Input Connections 18

Connect the Power Cord 18

Output Connections 18

Current Ratings 18

Voltage Drops and Lead Resistance 19

Remote Sensing 19

Remote Sense Leads 20

Maintaining Stability while Remote Sensing 22

Output Compensation (High Mode/Low Mode) 22

Local Sensing 23

OVP Considerations 24

External Protection Connections 24

Digital I/O Connections 25

viii

Controller Connections 26

HP-IB Interface 26

RS-232 Interface 26

4 - TURN-ON CHECKOUT 29

Checkout Procedure 29

In Case of Trouble 31

Error Messages 31

Line Fuse 31

5 - FRONT PANEL OPERATION 33

Introduction 33

Front Panel Description 33

System Keys 35

Function Keys 36

Immediate Action Keys 36

Scrolling Keys 36

Metering Keys 37

Output Control Keys 38

Entry Keys 39

Examples of Front Panel Programming 40

1 - Setting the Output Voltage, Current, and Compensation 40

2 - Querying and Clearing Output Protection and Errors 41

3 – Making Front Panel Measurements 42

4 - Programming External Protection and the Digital Port Functions 44

5 - Setting the HP-IB Address and RS-232 Parameters 44

6 - Saving and Recalling Operating States 45

6 - INTRODUCTION TO PROGRAMMING 47

HP-IB Capabilities of the DC Source 47

HP-IB Address 47

RS-232 Capabilities of the DC Source 47

RS-232 Data Format 47

Baud Rate 47

RS-232 Flow Control 48

Introduction to SCPI 48

SCPI References 48

HP-IB References 48

Conventions Used in This Guide 49

Types of SCPI Commands 49

Multiple Commands in a Message 50

Moving Among Subsystems 50

Including Common Commands 51

Using Queries 51

Types of SCPI Messages 51

The Message Unit 52

Headers 52

Query Indicator 52

Message Unit Separator 52

Root Specifier 52

Message Terminator 52

SCPI Data Formats 53

Numerical Data Formats 53

Suffixes and Multipliers 53

Response Data Types 53

SCPI Command Completion 54

Using Device Clear 54

RS-232 Troubleshooting 55

SCPI Conformance Information 55

SCPI Confirmed Commands 55

Non-SCPI Commands 55

7 - PROGRAMMING THE DC SOURCE 57

Introduction 57

Programming the Output 57

Power-on Initialization 57

Enabling the Output 57

Output Voltage 58

Output Current 58

Triggering Output Changes 59

SCPI Triggering Nomenclature 59

Output Trigger System Model 59

Setting the Voltage or Current Trigger Levels 59

Initiating the Output Trigger System 60

Generating Triggers 60

Making Measurements 61

Controlling Measurement Samples 61

Current Ranges and Measurement Detector 62

Window Functions 62

Voltage and Current Measurements 63

Pulse Measurements 63

Internally Triggered Measurements 65

SCPI Triggering Nomenclature 65

Measurement Trigger System Model 65

Initiating the Measurement Trigger System 66

Selecting the Measurement Trigger Source 66

Generating Measurement Triggers 66

Pre-event and Post-event Triggering 68

Programming the Status Registers 69

Power-On Conditions 69

Operation Status Group 71

Questionable Status Group 72

Standard Event Status Group 72

Status Byte Register 72

Determining the Cause of a Service Interrupt 73

Servicing Operation Status and Questionable Status Events 73

Monitoring Both Phases of a Status Transition 74

Inhibit/Fault Indicator 74

Remote Inhibit (RI) 74

Discrete Fault Indicator (DFI) 75

Using the Inhibit/Fault Port as a Digital I/O 75

8 - LANGUAGE DICTIONARY 77

Introduction 77

Subsystem Commands 77

Common Commands 81

Programming Parameters 81

Calibration Commands 82

CALibrate:CURRent 82

CALibrate:CURRent:MEASure:LOWRange 82

CALibrate:CURRent:MEASure:AC 82

CALibrate:CURRent:NEGative 82

CALibrate:DATA 83

CALibrate:LEVel 83

CALibrate:PASSword 83

CALibrate:SAVE 83

CALibrate:STATe 84

CALibrate:VOLTage 84

CALibrate:VOLTage:PROTection 84

Display Commands 85

DISPlay 85

DISPlay:MODE 85

DISPlay:TEXT 85

Measurement Commands 86

MEASure:ARRay:CURRent? FETCh:ARRay:CURRent? 86

MEASure:ARRay:VOLTage? FETCh:ARRay:VOLTage? 86

MEASure:CURRent? FETCh:CURRent? 87

MEASure:CURRent:ACDC? FETCh:CURRent:ACDC? 87

MEASure:CURRent:HIGH? FETCh:CURRent:HIGH? 87

MEASure:CURRent:LOW? FETCh:CURRent:LOW? 88

MEASure:CURRent:MAXimum? FETCh:CURRent: MAXimum? 88

MEASure:CURRent:MINimum? FETCh:CURRent:MINimum? 88

MEASure:VOLTage? FETCh:VOLTage? 89

MEASure:VOLTage:ACDC? FETCh:VOLTage:ACDC? 89

MEASure:VOLTage:HIGH? FETCh:VOLTage:HIGH? 89

MEASure:VOLTage:LOW? FETCh:VOLTage:LOW? 90

MEASure:VOLTage:MAXimum? FETCh:VOLTage:MAXimum? 90

MEASure:VOLTage:MINimum? FETCh:VOLTage:MINimum? 90

SENSe:CURRent:DETector 91

SENSe:CURRent:RANGe 91

SENSe:FUNCtion 92

SENSe:SWEep:OFFSet:POINts 92

SENSe:SWEep:POINts 92

SENSe:SWEep:TINTerval 92

SENSe:WINDow 93

Output Commands 94

OUTPut 94

OUTPut:DFI 94

OUTPut:DFI:SOURce 94

OUTPut:PON:STATe 95

OUTPut:PROTection:CLEar 95

OUTPut:PROTection:DELay 95

OUTPut:RI:MODE 96

OUTPut:TYPE 96

[SOURce:]CURRent 97

[SOURce:]CURRent:PROTection:STATe 97

[SOURce:]CURRent:TRIGger 97

[SOURce:]DIGital:DATA 98

[SOURce:]DIGital:FUNCtion 98

[SOURce:]VOLTage 98

[SOURce:]VOLTage:PROTection 99

[SOURce:]VOLTage:PROTection:STATe 99

[SOURce:]VOLTage:TRIGger 99

Inhaltsverzeichnis

Andere Agilent Technologies Stromversorgung Handbücher

Agilent Technologies

Agilent Technologies E3632A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 668xA Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6033A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6030A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E3632A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6111A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 729-0800 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6023A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 654xA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6029A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6443B Service-Handbuch

Agilent Technologies

Agilent Technologies 6116A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E364XA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 66 A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies N8900 series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6621A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E3632A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6625A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 66312A Betriebsanleitung

Agilent Technologies

Agilent Technologies E3633A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6112A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 66000A Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung

DTS

DTS Megashock 5 Bedienungsanleitung