Agilent Technologies 1100 Series Bedienungsanleitung
XCALI-97190 Revision B July 2007
Agilent®1100 Series
LC Devices
Connecting the Hardware and Triggering Data
Acquisition
© 2007 Thermo Fisher Scientific Inc. All rights reserved.
Agilent®is a registered trademark of Agilent Technologies Inc. Hewlett-Packard®is a registered trademark
of Hewlett-Packard Company. LCQ™, LTQ™, LXQ™, MSQ™, TSQ™, and Xcalibur™are trademarks of
Thermo Fisher Scientific Inc.
Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the
product operation. This document is copyright protected and any reproduction of the whole or any part of this
document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific Inc.
The contents of this document are subject to change without notice. All technical information in this
document is for reference purposes only. System configurations and specifications in this document supersede
all previous information received by the purchaser.
Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or error-
free and assumes no responsibility and will not be liable for any errors, omissions, damage or loss that might
result from any use of this document, even if the information in the document is followed properly.
This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This
document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of
Sale shall govern all conflicting information between the two documents.
Release history: First release February 2007, second release July 2007
For Research Use Only. Not regulated for medical or veterinary diagnostic use by U.S. Federal Drug
Administration or other competent authorities.
Thermo Scientific Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition iii
C
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Safety and Special Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Contacting Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Chapter 1 Agilent Modules Supported by LC Devices Versions 2.0.2 and 2.1.0. . . . . . . . . . .1
Chapter 2 Connecting the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Ethernet Communication Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing a Network Card in an Agilent Module. . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting the Ethernet Communication Cables . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the External Contact Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Trigger Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3 Configuring the Autosampler for Contact Closure . . . . . . . . . . . . . . . . . . . . . . . . .11
Chapter 4 Triggering Data Acquisition with the Autosampler . . . . . . . . . . . . . . . . . . . . . . . .13
Chapter 5 Turning Off the Solvent Tracking Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Appendix A Upgrading an HP 1100 Series LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Contents
Thermo Scientific Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition v
P
Preface
About This Guide
This guide describes how to hardwire an Agilent®1100 Series LC to a Thermo Scientific
mass spectrometer and the data system computer, configure an Agilent autosampler for
contact closure from within the Xcalibur Instrument Configuration program, and trigger data
collection with an Agilent autosampler.
This guide also describes how to upgrade a Hewlett-Packard®1100 Series LC to an
Agilent 1100 Series LC with Ethernet communication.
Related Documentation
In addition to this guide, Thermo Fisher Scientific provides Help available from within the
Xcalibur software.
Safety and Special Notices
Make sure you follow the precautionary statements presented in this guide. The safety and
other special notices appear in boxes.
Safety and special notices include the following:
CAUTION Highlights hazards to humans, property, or the environment. Each CAUTION
notice is accompanied by an appropriate CAUTION symbol.
CAUTION Highlights electric shock related hazards to human beings. Each electric shock
notice is accompanied by the international High Voltage symbol.
IMPORTANT Highlights information necessary to prevent damage to software, loss of
data, or invalid test results; or might contain information that is critical for optimal
performance of the system.
Preface
vi Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition Thermo Scientific
Safety Precautions
To connect the Agilent 1100 Series LC stack to a Thermo Scientific mass spectrometer, you
must install an external contact board in one of the Agilent modules and a LAN interface
board in a second Agilent module. To install a board, you must remove the cover from the
optional board slot. Figure 2 on page 6 shows the location of the slot on the back panel of the
detector.
Before you remove the slot cover from an Agilent 1100 Series module, do the following:
• Turn the power switch to the Off position and unplug the power cable.
• Refer to the Reference Manual for the module for additional safety information and for
information on preventing ESD damage caused by an electrical discharge.
Contacting Us
There are several ways to contact Thermo Fisher Scientific.
YTo contact Technical Support
Find software updates and utilities to download at www.mssupport.thermo.com.
Note Highlights information of general interest.
Tip Helpful information that can make a task easier.
CAUTION To avoid an electric shock, always turn off an Agilent module and unplug
it from line power before you remove its cover.
CAUTION To prevent damage to an instrument, always use ESD protection when
handling electronic boards and components.
Phone 800-685-9535
Fax 561-688-8736
E-mail TechSupport.C+MS@thermofisher.com
Knowledge base www.thermokb.com
Preface
Thermo Scientific Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition vii
YTo contact Customer Service for ordering information
YTo suggest changes to documentation or to Help
• Fill out a reader survey online at www.thermo.com/lcms-techpubs.
• Send an e-mail message to the Technical Publications Editor at
techpubs.finnigan-lcms@thermofisher.com.
Phone 800-532-4752
Fax 561-688-8731
Web site www.thermo.com/finnigan
Thermo Scientific Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition 1
1
Agilent Modules Supported by LC Devices
Versions 2.0.2 and 2.1.0
Tab l e 1 lists the model number and firmware versions for the Agilent 1100 Series LC
modules that are supported by the Xcalibur 2.0 and higher data system.
YTo check the firmware version of an Agilent 1100 module
1. Make sure that the Agilent 1100 Series modules are connected by CAN communication
cables, that all the modules are turned on, and that the Agilent 1100 Control Module is
connected.
Refer to the Agilent 1100 Series LC reference manuals for instructions on how to connect
the CAN cables.
2. Press the Esc key on the Control Module until System appears in the upper-left corner of
the LCD display.
3. Press the F4 key on the Control Module to access the Records LCD display.
Table 1. Xcalibur 2.0 supported firmware versions for the Agilent 1100 Series LC
Module Model Number Firmware Version
Binary pump G1312A A.06.01 (012)
Quaternary pump G1311A A.06.01 (012)
Autosampler G1313A A.06.01 (012)
Thermostatted autosampler G1329A A.06.01 (012)
Well-plate autosampler G1367A A.06.01 (012)
Thermostatted column compartment G1316A A.06.01 (012)
Variable wavelength detector G1314A A.06.01 (012)
Diode-array detector G1315A A.06.01 (012)
Multiple wavelength detector*
*Only works with version B of the Control Module.
G1365B A.06.01 (012)
1Agilent Modules Supported by LC Devices Versions 2.0.2 and 2.1.0
2Agilent 1100 Series LC Devices Connecting the Hardware and Triggering Data Acquisition Thermo Scientific
4. Check the firmware versions of the Agilent 1100 Series modules. Refer to Table 1 for the
firmware versions supported by the Xcalibur 2.0. and higher data system.
Records
Module Product Serial# Version On-time EMF
Time Ready
Andere Handbücher für 1100 Series
18
Inhaltsverzeichnis
Andere Agilent Technologies Prüfgeräte Handbücher
Agilent Technologies
Agilent Technologies 8453 Verdrahtungsschema
Agilent Technologies
Agilent Technologies Infiniium 9000 Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies 54621A Handbuch
Agilent Technologies
Agilent Technologies 280-DS Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Agilent Technologies
Agilent Technologies InfiniiVision 6000 Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies E4406A VSA Series Handbuch
Agilent Technologies
Agilent Technologies 93000 SOC Series Installationsanleitung
Agilent Technologies
Agilent Technologies 8960 Betriebsanleitung
Agilent Technologies
Agilent Technologies DSO-X-2024A Bedienungsanleitung
Agilent Technologies
Agilent Technologies HP 10070A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 85032F Handbuch
Agilent Technologies
Agilent Technologies Medalist x6000 Bedienungsanleitung
Agilent Technologies
Agilent Technologies N5341A Bedienungsanleitung
Agilent Technologies
Agilent Technologies InfiniiVision 7000 Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies E5022B Betriebsanleitung
Agilent Technologies
Agilent Technologies 81250 Bedienungsanleitung
Agilent Technologies
Agilent Technologies AuroraPresto Bedienungsanleitung
Agilent Technologies
Agilent Technologies U1610/20A Bedienungsanleitung
