Agilent Technologies Medalist i3070 Series Benutzerhandbuch

©Agilent Technologies 2010 Medalist i3070 System Installation 1-1

System Installation

■Tools Required, 1-2

■Getting Started, 1-3

■Setting Up the Support Arm with Monitor, Keyboard,

and Mouse, 1-4

■Setting Up the Strip Printer, 1-15

■Preparing the Testhead, 1-16

■Powering the PDU and Controller, 1-19

■Installing a Support Bay and Instrument Rack, 1-21

■Enabling the Testhead, 1-25

■Verifying the Vacuum Subsystem, 1-28

■Verifying the Testhead, 1-32

■Completing the Installation, 1-33

■In Case of Difficulty, 1-34

CAUTION

;The Medalist In-circuit Test System should only

be installed by an Agilent-Authorized Service

Representative.

Testhead boot conflicts may occur if this system is

on a network with Medalist 3070 UNIX

controllers with IP addresses other than in the

10.3.112.XX series.

CAUTION

;The Medalist test development software requires

that decimals in the board file use a period (.) and

not any other character such as a comma. Make

use that Windows is set to use a period for

decimals. (Select Control Panel > Regional and

Language Options > Regional Options tab. Click

Customize; in the Numbers tab ensure that the

selected Decimal symbol is a period.)

©Agilent Technologies 2010 Medalist i3070 System Installation 1-2

Tools Required

Tools Required These tools are needed in addition to the tools supplied

with the system shipment:

■BNC-to-dual banana coaxial cable for Diagnostics

■BNC(F)-to-BNC(F) (barrel) connector for

Diagnostics

■Pin Verification Fixture (PVF) for Diagnostics

■T10 & T20 Torx drivers

■#2 Phillips or Posi screwdriver

■1/4-inch flat blade screwdriver

■5- and 10-mm hex key wrenches

■Diagonal-cutters to cut straps

■Utility knife to open boxes

■7/16-inch and 9/16-inch, 3/8-inch square-drive

sockets

■6-inch-long, 3/8-inch square-drive extension

■3/8-inch square-drive ratchet

■Cordless drill – 14.4 Volt, 3/8-inch drill / driver kit

©Agilent Technologies 2010 Medalist i3070 System Installation 1-3

Getting Started

Getting Started 1 Verify that site preparation is complete.

a View the customer’s completed Site Preparation

checklist.

b Obtain a copy of the system plan drawing.

2 Check for shipping damage.

If shipping damage is found, contact your local

Agilent representative.

3 Uncrate the system.

4 Check the system and the contents of all crates

and boxes against the order.

Check that:

■A support bay is included with four-module

systems to hold DUT power supplies.

■The strip printer and licenses are included.

■The bag on the testhead contains:

• a pod key,

• a probe cradle,

• a certificates of calibration,

• a certificate of hardware address for the System

Card, and

• configuration printouts.

■The bag on the testhead cradle contains:

• a female quick-disconnect compressed air

fitting, and

• an Installation Kit (it contains various tools and

parts).

©Agilent Technologies 2010 Medalist i3070 System Installation 1-4

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

Setting Up the

Support Arm with

Monitor, Keyboard,

and Mouse

The default location for the controller’s monitor,

keyboard and mouse support arm is on the right side of

the testhead, when facing the testhead from the front.

If the preferred location of the support arm is on the left

side, the pod cover(s) must be removed, then the

monitor, keyboard and mouse wiring must be re-routed.

■Install the Support Arm, Monitor, Keyboard, and

Mouse, 1-5

■Adjust the Support Arm, 1-14

Safety Precautions

Pinch hazard locations when performing the following

procedures include the following.

Figure 1-1 Pinch hazard locations

This label on the machine indicates the location

of a pinch hazard that may cause minor or

moderate injury if the warning is ignored.

Do not place your fingers between

the collar and support arm when

adjusting the height of the arm.

Do not place your fingers between

the monitor support and the support

arm when rotating the support arm.

Do not place your fingers near the

hinges when moving the keyboard

tray up or down.

©Agilent Technologies 2010 Medalist i3070 System Installation 1-5

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

Install the Support Arm, Monitor, Keyboard, and

Mouse

Follow the instructions in Table 1-1.

Table 1-1 Install the support arm, monitor, keyboard, mouse

Task

1 Remove the two shipping bolts.

Do this so that the testhead can be rotated. Figure 1-3 on page 1-13 shows the location of the shipping bolts.

CAUTION

;Remove the shipping bolts before attempting to rotate the testhead. Otherwise, damage can result.

Shipping bolts can be stored for later use in the holes used by the testhead pallet shipping brackets.

2 If the support arm will be installed on the left (non-default) side, follow the steps for this task. Otherwise, continue with

task 3.

CAUTION

;Before rotating the testhead, remove all objects from the rotational path of the testhead. Damage could

result if the testhead hits anything while being rotated.

Remove the pod cover:

a If testhead connectors (BNC) are visible over the pod cover, rotate the testhead about 10 degrees to allow the pod cover

to be removed.

Apply PDU power to activate the testhead rotation switch. See Powering the PDU and Controller on page 1-19.

b Use a T20 Torx driver to remove the pod cover screws and then remove the pod cover.

c Remove power to the PDU if connected.

©Agilent Technologies 2010 Medalist i3070 System Installation 1-6

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

3 Install the pole mount assembly.

a Pry the plastic square plug (if present) from the column of the testhead cradle where the pole mount assembly will be

installed.

b Install the pole mount assembly in the column.

c Open the pod door (if installing on the right).

Secure the pole mount assembly to the cradle with the

screws and washers provided.

Table 1-1 Install the support arm, monitor, keyboard, mouse (continued)

Task

©Agilent Technologies 2010 Medalist i3070 System Installation 1-7

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

4 Install support arm assembly.

a Position the safety collar on the pole mount assembly

and tighten the screw using the Allen key.

b Hold the support arm with both hands while moving it

down onto the collar on the pole mount assembly.

Tighten with the hand lever.

Table 1-1 Install the support arm, monitor, keyboard, mouse (continued)

Task

safety collar

hand lever

©Agilent Technologies 2010 Medalist i3070 System Installation 1-8

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

5 Install the keyboard tray.

a Secure the keyboard tray to the support arm using the

four nuts and bolts provided.

Alternatively, you can attach the keyboard tray to the

support arm first.

Then flip the keyboard tray up before installing the

support arm on the pole mount assembly.

Table 1-1 Install the support arm, monitor, keyboard, mouse (continued)

Task

keyboard

tray

fasten with

nuts & bolts

©Agilent Technologies 2010 Medalist i3070 System Installation 1-9

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

6 Install the monitor.

a Remove the four screws on the monitor stand and

remove the monitor stand.

b Secure the monitor onto the monitor support with the

screws provided. Tighten the screws by hand.

c To adjust the height of the monitor, loosen the screw on

the monitor support using an Allen key.

7 Install keyboard and mouse.

To position the mouse on the right, route the mouse and keyboard cables through the hole on the right side of the

keyboard tray. (Do the opposite to position the mouse on the left.)

Table 1-1 Install the support arm, monitor, keyboard, mouse (continued)

Task

monitor stand

loosen screw for

height adjustment

tighten screws to secure monitor (4 screws)

©Agilent Technologies 2010 Medalist i3070 System Installation 1-10

Setting Up the Support Arm with Monitor, Keyboard, and Mouse

8 Route the monitor, keyboard and mouse cables:

CAUTION

;If the cables are not routed with enough slack (between 130 - 150 cm), they can be damaged when the

support arm is moved.

NOTE

The keyboard and mouse have cables which are long enough to allow installation on the left side.

For two- and four-module systems, a second video monitor cable is pre-installed to accommodate support

arm installation on the left side. For one-module systems, the existing video monitor cable is long enough

to reach to the left side. Re-route it through the testhead cable troughs.

It may be necessary to obtain a 8120-1763 power cord extension cable to connect power from the PDU to

the video monitor. Route the power cable through the testhead cable trough.

Table 1-1 Install the support arm, monitor, keyboard, mouse (continued)

Task

Andere Handbücher für Medalist i3070 Series

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies XX3625 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8453 Verdrahtungsschema

Agilent Technologies

Agilent Technologies AuroraPresto Bedienungsanleitung

Agilent Technologies

Agilent Technologies J-BERT N4903A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision MSO6012A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81250 Betriebsanleitung

Agilent Technologies

Agilent Technologies 3070 Series Betriebsanleitung

Agilent Technologies

Agilent Technologies Infinium DCA 86100A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16451B Bedienungsanleitung

Agilent Technologies

Agilent Technologies ProBER 2 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 2000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Bedienungsanleitung

Agilent Technologies

Agilent Technologies N4413A Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Einrichtungshandbuch

Agilent Technologies

Agilent Technologies E5035A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83480A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85105A Option 50 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies J-BERT N4903 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16442A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85050B Handbuch

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16048D Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8922M Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung