Agilent Technologies N5230AU-974 Installations- und Betriebshandbuch

Agilent Kit Number: N5230-60115

Agilent Document Number: N5230-90022

Printed in USA September 2006

Installation Note

Extended Frequency Range Upgrade Kit

To Upgrade Option 225 to Option 425

Upgrade Kit Order Number: N5230AU-974

For N5230A Option 225 PNA-L (20 GHz, 2-Port, Configurable Test Set)

(With serial numbers prefixed MY4640 and above.)

2Installation Note N5230-90022

WARRANTY STATEMENT

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT

TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE

MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL

WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN.

SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH

WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT

WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL

CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING

Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION

Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note N5230-90022 3

Getting Assistance from Agilent

By internet, phone, or fax, get assistance with all your test and measurement needs.

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent

office are available on the Web at:

http://www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

Description of the Upgrade

This upgrade extends the upper frequency limit of your 20 GHz configurable test set analyzer

(N5230A Option 225) to 40 GHz. This is done by installing Option F40. After installation of

this upgrade, your anlayzer will be an N5230A Option 425.

Option F40 provides the necessary 40 GHz components and cabling to allow your analyzer to

measure signals up to 40 GHz.

About Installing the Upgrade

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . N5230A Option 225 (20 GHz, 2-port,

configurable test set) (With serial numbers

prefixed MY4640 and above.)

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 2.0 hours

Estimated adjustment time . . . . . . . . . . . . . . . . . 0.5 hours

Estimated full instrument calibration time . . . . 4.5 hours

4Installation Note N5230-90022

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any part is missing or damaged,

contact Agilent Technologies. Refer to “Getting Assistance from Agilent” on page 3.

Table 1 Contents of Upgrade Kit N5230-60115

Ref

Desig. Description Qty Part

Number

Installation note (this document) 1 N5230-90022

A18 Modulator/amplifier 26.5 (MA 26.5) 1 5087-7280

A19 Modulator/amplifier/switch/splitter 50 (MASS 50) 1 5087-7278

A20 Mixer brick 50 1 5087-7279

A21, A22 Test port coupler, 50 GHz 2 5086-7518

A25, A26 Attenuator, 60 dB, 50 GHz 2 33325-60004

Attenuator bracket 2 E8364-00002

Machine screw, M3.0 x 10 pan head (for attaching A18 MA 26.5) 3 0515-0374

Rubber bumper (for A21 and A22 test port couplers) 2 0403-0285

4-dB pad 1 0955-0583

Test set deck front panel, 50 GHz 1 E8364-00014

Cable tie (to secure cables W47 and W51 to the side frame) 3 1400-0249

40 GHz nameplate 1 N5230-80003

Ribbon cable, A18 MA 26.5 to A16 test set motherboard 1 N5230-60014

W3 RF cable, A6 multiplier board to A20 mixer brick 1 N5230-20043

W6 RF cable, A8 multiplier board to A18 MA 26.5 1 N5230-20044

W7 RF cable, A18 MA 26.5 to A19 MASS 50 1 N5230-20033

W40 RF cable, A19 MASS 50 to A25 port 1 step attenuator 1 N5230-20030

W41 RF cable, A19 MASS 50 to A26 port 2 step attenuator 1 N5230-20031

W42 RF cable, A25 port 1 step attenuator to PORT 1 SOURCE OUT 1 E8364-20053

W43 RF cable, A26 port 2 step attenuator to PORT 2 SOURCE OUT 1 E8364-20054

W44 RF cable, PORT 1 CPLR THRU to A21 test port 1 coupler 1 N5230-20047

W45 RF cable, PORT 2 CPLR THRU to A22 test port 2 coupler 1 N5230-20048

W46 RF cable, A19 MASS 50 to REFERENCE 1 RCVR R1 IN 1 N5230-20036

W47 RF cable, A19 MASS 50 to REFERENCE 2 RCVR R2 IN 1 N5230-20038

W48 RF cable, PORT 1 CPLR ARM to A21 test port 1 coupler 1 E8364-20043

W49 RF cable, PORT 2 CPLR ARM to A22 test port 2 coupler 1 E8364-20044

W50 RF cable, PORT 1 RCVR A IN to A20 mixer brick (A) 1 N5230-20035

W51 RF cable, REFERENCE 1 RCVR R1 IN to A20 mixer brick (R1) 1 N5230-20037

W52 RF cable, REFERENCE 2 RCVR R2 IN to A20 mixer brick (R2) 1 N5230-20039

W53 RF cable, PORT 2 RCVR B IN to A20 mixer brick (B) 1 N5230-20032

W60 Front-panel jumper 6 E8364-20059

Installation Note N5230-90022 5

Installation Procedure for the Upgrade

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING

This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always have a grounded, conductive table mat in front of your test equipment.

•always wear a grounded wrist strap, connected to a grounded conductive table mat, having

a 1 MΩresistor in series with it, when handling components and assemblies or when

making connections.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

•always ground yourself before you clean, inspect, or make a connection to a static-sensitive

device or test port. You can, for example, grasp the grounded outer shell of the test port or

cable connector briefly.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“ESD Equipment and Supplies Required for the Installation” on page 6 for part numbers.

Figure 1 ESD Protection Setup

6Installation Note N5230-90022

Tools Required for the Installation

ESD Equipment and Supplies Required for the Installation

Equipment Required for Post-Upgrade Adjustments

Overview of the Installation Procedure

Step 1. Remove the Outer and Inner Covers.

Step 2. Remove the Front Panel Assembly.

Step 3. Remove the 20 GHz Bottom Cables.

Step 4. Remove the Test Set Deck Front Panel.

Step 5. Remove the 20 GHz Top to Bottom Cables.

Step 6. Remove the 20 GHz Components.

Step 7. Install the 50 GHz Components.

Step 8. Install the 50 GHz Top to Bottom Cables.

Step 9. Assemble and Install the New Test Set Deck Front Panel.

Step 10. Install the 50 GHz Bottom Cables.

Step 11. Replace the Nameplate.

Step 12. Reinstall the Front Panel Assembly.

Step 13. Reinstall the Inner and Outer Covers.

Step 14. Enable Option F40.

Step 15. Perform Post-Upgrade Adjustments.

Description Agilent Part Number

T-10 TORX driver (set to 9 in-lbs) N/A

T-20 TORX driver (set to 21 in-lbs) N/A

5/16-inch torque wrench (set to 10 in-lbs) N/A

1-inch torque wrench (set to 72 in-lbs) N/A

Description Agilent Part Number

ESD grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

ESD heel strap (for use with conductive floors) 9300-1308

Equipment Type Model or

Part Number

Alternate Model or

Part Number

Power meter E4418B/E4419B E4418A/E4419A

Power sensor, 2.4 mm 8487A None

Adapter, 2.4 mm (f) to 2.4 mm (f) 11900B 85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f) 85133C 85133E

Installation Note N5230-90022 7

Step 1. Remove the Outer and Inner Covers

Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front

handles in the vertical position. Do not place the analyzer on its front panel

without the handles. This will damage the front panel assemblies.

Refer to Figure 2 for this procedure.

1. Disconnect the power cord (if it has not already been disconnected).

2. With a T-20 TORX driver, remove the strap handles (item ①) by loosening the screw

(item ②) on each end of each handle.

3. With a T-20 TORX driver, remove the four rear panel feet (item ③) by removing the center

screws (item ④).

4. Slide the four bottom feet (item ⑤) off the cover.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

8Installation Note N5230-90022

Remove the Inner Cover

1. Place the analyzer top-side up on a flat surface.

2. Using a T-10 TORX driver, remove the eleven screws (item ①).

3. Lift off the cover.

Figure 3 Inner Cover Removal

Installation Note N5230-90022 9

Step 2. Remove the Front Panel Assembly

Refer to Figure 4 for this procedure.

1. With a 5/16-inch wrench, remove the six semi-rigid jumpers (item ①) from the front panel.

2. With a T-10 TORX driver, remove the eight screws (item ②) from the sides of the frame.

CAUTION

Before removing the front panel from the analyzer, lift and support the front of

the analyzer chassis.

3. Slide the front panel over the test port and other front panel connectors.

4. Disconnect the front panel interface ribbon cable (item ③). The front panel is now free

from the analyzer.

Figure 4 Front Panel Assembly Removal

10 Installation Note N5230-90022

Step 3. Remove the 20 GHz Bottom Cables

Refer to Figure 5 for this procedure.

1. Place the analyzer bottom-side up on a flat surface.

2. Remove the following cables in the order listed:

• W40 A17 MASS 26.5 to A25 port 1 step attenuator

• W42 A25 port 1 step attenuator to PORT 1 SOURCE OUT

• W44 PORT 1 CPLR THRU to A21 test port 1 coupler

• W46 A17 MASS 26.5 to REFERENCE 1 SOURCE OUT

• W51 REFERENCE 1 RCVR R1 IN to A20 mixer brick (R1)

• W48 A21 test port 1 coupler to PORT 1 CPLR ARM

• W50 PORT 1 RCVR A IN to A20 mixer brick (A)

• W41 A17 MASS 26.5 to A26 port 2 step attenuator

• W43 A26 port 2 step attenuator to PORT 2 SOURCE OUT

• W45 PORT 2 CPLR THRU to A22 test port 2 coupler

• W47 A17 MASS 26.5 to REFERENCE 2 SOURCE OUT

• W52 REFERENCE 2 RCVR R2 IN to A20 mixer brick (R2)

• W49 A22 test port 2 coupler to PORT 2 CPLR ARM

• W53 PORT 2 RCVR B IN to A20 mixer brick (B)

Figure 5 20 GHz Bottom Cables Removal

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies E8285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85057B Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 34980A Montage- und Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 90000 X Bedienungsanleitung

Agilent Technologies

Agilent Technologies Ininiium 9000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies U2802A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85056A Handbuch

Agilent Technologies

Agilent Technologies 85105A Option 50 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Einrichtungshandbuch

Agilent Technologies

Agilent Technologies 54853A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E7490A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8922M Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85056K Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5530 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 3000 Series Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Handbuch

Agilent Technologies

Agilent Technologies 16533A 1-GSa/s Handbuch

Agilent Technologies

Agilent Technologies 8960 Betriebsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 7000B Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies N4010A Montage- und Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung

Sealey

Sealey TA130 Bedienungsanleitung