AGM A-19 Bedienungsanleitung

1

PRECAUTIONS ...........................................................................................................2

INFORMATION FOR USERS APPLICABLE IN EUROPEAN UNION COUNTRIES

2

INFORMATION FOR USERS APPLICABLE IN UNITED STATES OF AMERICA

2

INSTALLATION

2

POWER CONNECTION

2

MAINTENANCE

2

TRANSPORTING THE MONITOR

2

GETTING STARTED

3

PACKAGE CONTENTS

3

INSTALLATION OF FIRST USE

4

IDENTIFYING PARTS AND CONTROLS

4

FUNCTIONS OF THE BUTTONS AND INDICATOR:

4

SETUP

5

CUSTOMIZING YOUR MONITOR

6

Working wirh OSD Group

6

Hotkey and the Characteristic Functions Introduction

6

OSD Icin List

7

TROUBLESHOOTING 9

TECHNICAL FEATURES AND SPECIFICATIONS

10

INTERFACE FREQUENCY 11

ADDENDUM

12

REGULATIONS

14

FCC COMPLIANCE 14

TCO’99

15

TABLE OF CONTENTS

2

Information for users applicable in European Union

countries

The symbol on the product or its packaging signifies that this product has to be disposed separately

from ordinary household wastes at its end of life. Please kindly be aware that this is your

responsibility to dispose electronic equipment at recycling centers so as to help conserve natural

resources. Each country in the European Union should have its collection centers for electrical and

electronic equipment recycling. For information about your recycling drop off area, please contact

your local related electrical and electronic equipment waste management authority or the retailer

where you bought the product.

Information for users applicable in United States of

America

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO

LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES

ALLIANCE AT WWW.EIAE.ORG. FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK WWW.LAMPRECYCLE.ORG.

Installation

1.

Do

not

cover

or

block

the

ventilation

ports

on

the

rear

of

the

monitor

.

2.

Do

no

t

install

the

monitor

close

to

heat

sources

such

as

radiators

or

air ducts,

or

i

n

a

location

exposed

to

direct sunlight,

excessive

dust,

mechanical

vibration, or

shock.

Power connection

1. Use the correct power cord for your local voltage.

2. Use an accessible outlet close to the monitor.

3. Do not allow anything to rest on the power cable.

4. Only use the power adapter attached to the monitor.

5. Disconnect the power cable from the power supply if:

5.1

Y

ou

w

ill

not

use

the

monitor

for

an

extended

period.

5.2

The

cable

is

damaged

or

frayed.

5.3

The

monitor

has

been

dropped

or

the

cabinet

damaged.

5.4

A

distinct

change

in

performance

indicates

a

need

for

servicing.

Maintenance

1.

Clean

the

cabinet

and

controls

wit

h

a

s

oft

cloth

lightly

moistened

wit

h

a

mild

detergent

solution.

Do

not

use

any

abrasive

materials

or

solvents

such

as

alcohol

or

benzene.

2.

Do

not

r

ub,

touch,

or

tap

the

surface

of

the

screen

with

sharp

or

abrasive

items

such

as

pens

or

screwdrivers,

as

the

screen

may

scratch.

3.

Do

no

t

insert

objects

or

spill

liquids

into

the

ventilation

ports

on

the

monitor

’

s

rear

,

a

s

fire,

electric

shock,

an

d

/

o

r

unit

failure

may

result.

Transporting the monitor

1.

When

transporting

the

monitor

for

repair

or

shipment,

fold

the

base

of

the

monitor

back

until

it

becomes

straight.

Then

wrap

the

monitor

and

its

attachments

with

the

original

c

arton

and

packing

materials.

Precauciones

3

Package contents

Before

beginning,

ensure

that

the

carton

contains

the

following

items:

1. LCD Monitor

2. Power cord (The plug may vary according to the electrical standard for your area)

3.

V

ideo

Signal

Cable

(Analog,

D

-

SU

B

C

a

ble

)

4.

Audio

cable

(optional)

5.

CD-ROM

6.

Quick

Installation

Guide

Gettin

g

Started

4

Installation of First Use

1.

The

installatio

n

o

f the

monitor

is

very

simple.

Take

the

monitor

from

the

packing

box

and

remove

all

the

packing

materials.

And

then

put

the

monitor

on

the

desk

carefully;

fold

the

monitor

base,

so

that

the

monitor

can

stand

on

the

desk

properly.

Next,

adjust

the

monito

r

t

o

the

desired

position

according

to

the

seat

and other

factors.

Identifying parts and controls

1.

The

LED

indicator

and

control

buttons

are

as

follows:

2.

The

connection

ports

are

as

follows:

Functions of the buttons and indicator:

Button

Functions

1.

T

urn

on

the

monitor

2.

Activate

the

OSD

control

menu

3.

Select

the

specific

function

4.

T

urn

of

f

the

monitor

by

pressing

the

button

fo

r

3

seconds

1.

Activate the Volume control menu, and increase the value (optional)

2.

View the next function in the main OSD menu clockwise

3.

Increase the value of specific function which has been selected

1.

Activate

the

V

olume

control

menu,

and

decrease

the

value

(optional)

2.

V

iew

the

in

the

main

OSD

menu

counter-clockwise

3.

Decrease

the

value

of the

specific

function

which

has

been

selected

1.

Optimize

the

picture

performance

automatically

Indicador LED

1.

Green

color

indicates

that

the

monitor

is

in

“active”

mode

(normal

operation).

2.

Amber

color

indicates

that

the

monitor

is

in

“sleep”

mode

(power

saving

mode

or

no

signal

input).

3.

Not

lit

indicates

that

the

monitor

is

in

“of

f”

mode

(monitor

power

of

f).

5

Setup

1. Connecting

video

(Note:

Before

connecting

computer

,

ensure

the

resolution

and

refresh

rat

e

o

f

the

computer

do

not

exceed

the

following setting

s

-

resolution:

1280*1024,

refresh

rate:

75Hz.)

1.1

Turn

of

f

your

computer

1.2

Connect

the

video

signal

cable

to

the

VGA

port

of

your

PC,

tighten

the

screws

on

the

connector

onto

the

computer

1.3

Connect

the

other

end

of the

video

signal

cable

to

the

VGA-IN

port

at

the

back

of

the

monitor

,

t

ighten

the

screws

on

the

connector

to

the

monitor

2.

Connecting

powe

r

2.1

Plug

the

female

end

of

the

power

cord

in

to

the

AC-IN

port

at

the

back

of

the

monitor

2.2

Plug

the

male

end

of

the

power

cord

int

o

a

power

outlet

3.

Connecting

audio

(optional)

3.1

Plug

the

audio

cable

into

the

AUDIO

port

at

the

back

of

the

monitor

3.2

Plug

the

other

end

of

the

audio

cable

into

your

computer

or

other

audio

source

4.

Turning on the computer

5. Pressing the button at the back of the monitor to turn on the monitor

6. Removing the protection film from the monitor

You should be able to see the picture now. If not, refer to the “Troubleshooting” section.

6

Customizing

your

Monitor

The

On

Screen

Display

(OSD)

system

provide

s

a

full

range

of

customizable

tools

to

optimize

your

display

.

Important:

While

full

customization

is

available,

we

strongly

recommend

using

the

Auto

Adjustment

function,

which

is

preset

to

fully

optimize

your

monitor

’

s

performance.

Simply

press

the

＆

buttons

simultaneously

to

engage

the

Auto

Adjustment.

It

is

also

recommended

that

you

execute

the

function

following

any

change

made

to

your

display

from

your

computer.

W

orking

with

OSD Group

1. Press Menu button to activate the OSD menu.

2. Select the icon from the OSD menu with the ＆buttons.

3. Press Menu button to confirm the selection of a specific function.

4.

Press or to adjust the setting values.

5.

Press Menu button to exit from the sub-menu.

6. Press or to select the icon, and then press the Menu button to exit from the OSD

menu.

Introduction to Hotkeys

1. Auto Adjustment

While

the

OSD

menu

is

not

shown,

press

＆

buttons

simultaneously

to

optimize

the

picture

performance

automatically

(Y

ou

may

also

use

the

OSD

control

to

activate

the

Auto

Adjustment

function.

See

OSD

Menu

and

Icon

List

section)

2. Volume Control (optional)

While

the

OSD

menu

is

not

shown,

press

o

r

button

to

increase

or

decrease

the

audio

volume

level.

7

OSD

Icon

List

Icon

Functions

Detail

Auto

Adjustment

Optimize

the

picture

performance

automatically

(you

may

also

pres

s

an

d

buttons

simultaneously

,

while

the

OSD

menu

is

not

shown,

to

activate

the

function)

Brightness

Adjust

the

luminance

level

of

the

screen

Contrast

Adjust

the

contrast

level

(black

to

white

ratio)

of

the

screen

Sharpness

Adjust

the

sharpness

of

the

screen

Clock

Adjust

the

monitor’s

internal

sampling

clock

rate

Phase

Adjust

the

monitor

internal

signal

phase

Horizontal Position

Shift

the

position

of

the

screen

left

or

right

V

ertical

Position

Shift

the

position

of

the

screen

up

or

down

Color

T

e

mperature

Select

the

setting

of

screen

colo

r

–

Cool,

W

arm

or

User

Cool

(9300K)

Select

the

setting

of

screen

color

to

be

bluish

white

W

arm

(6500K

)

Select

the

setting

of

screen

color

to

be

reddish

white

User

Adjust

the

setting

of

screen

color

per

the

user

’

s

preference

R

Adjust

the

percentage

of

red

color

G

Adjust

the

percentage

of

green

color

B

Adjust

the

percentage

of

blue

color

OSD

Menu

Language

Select

your

own

preference

of

language

of

OSD

menu

There

are

9

languages

available

–

English,

German,

French,

Italian,

Spanish, Japanese,

Simplified

Chinese,

and

T

raditional

Chinese.

8

OSD

Menu

Position

Adjust

the

position

of

OSD

menu

on

the

screen.

Power

Saving

Mode

Select

between

Standard

and

Advanced

power

saving

modes.

See

addendum

for

details

Standard

Fulfill

EP

A

Energy

Star

power

management

requirement

Advanced

Activate

monitor

Life-Extension

function

Recall

Factory

Preset

Reset

monitor

parameters

back

to

factory

preset

values.

Exit

Disable

the

OSD

menu

9

Symptom

Check

Items

1.

No

picture

2.

LED

indicator

(at

the

right

side

of

the

monitor)

is

not

lit

1.Check

if

the

monitor

is

turned

on

(press

the

button

again).

2.

Check

if

the

power

cor

d

i

s

properly

connected

to

the

monitor

and

power

outlet.

3.

Check

if

there

is

electricity

coming

from

the

power

outlet

(use

another

device

to

check

for

power).

1.

No

picture

2.

LED

indicator

(at

the

right

side

of

the monitor)

is

orange

1.Check

if

your

computer

is

turned

on.

2.

Ensure

the

computer

is

not

in

power

saving

mode

(move

the

mouse

or

pres

s

a

key

on

the

keyboard

to

wake

up

the

computer).

3.Check

if

the

video

signal

cable

is

properly

connected

to

the

monitor

and

computer

.

1.

Picture

shows

“No

Signal

Input”

1.Check

if

your

computer

is

turned

on.

2.Check

if

the

video

signal

cable

is

properly

connected

to

the

monitor

and

computer

.

1.

Picture

shows

“Input

Signal

Out

of

Range”

1.Ensure

that

the

resolution

and/or

refresh

rate

is

set

correctly

.

(See

item

2.1

of Monitor

Installation

section)

1.

Picture

not

clear

1.Press the

buttons

simultaneously

to

activate

the

Auto

Adjustment

function.

2.Check

if

the

video

signal

cable

is

properly

connected

to

the

monitor

and

computer

.

3.Adjust

the

screen

resolution

and

refresh

rate

of

your

computer

to

SXGA.

(resolution:

1280*1024,

refresh

rate:

60Hz)

for

the

best

performance

Troubleshootin

g

AGM A-19 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken