Aim MX Bedienungsanleitung
1
www.aim-sportline.com Release 1.00 –October 12th 2018
1
Physical connection
The AiM loggers built to manage rear cameras are provided with a female metallic 5pins Binder
connector, placed on the device bottom and labelled as “VIDEO IN” (following image).
The Video In connector allows the connection of two different analog cameras, that may be activated as
here down described.
There is a wide number of analog cameras on the market. We have tested one of them, of which the
Amazon Code is: ASIN B01H1RFZYA .
This camera offers a couple of interesting options:
•the possibility to reverse the image
•the possibility to enable or disable the parking overlay view.
2
www.aim-sportline.com Release 1.00 –October 12th 2018
It has, as most of the analog cameras, a connection through standard RCA connectors (following right
image), for which we have developed the patch cables:
•Single RearMaster camera (cable length:
5m) ended with:
oMale metallic 5pins Binder
connector for connection to
AiM loggers;
oDC Power Connector (yellow)
to be connected to the camera
one;
oVideo RCA Connector (red) to
be connected to the camera
one.
•Double RearMaster camera (cable
length: 6m) ended with:
oMale metallic 5pins Binder
connector for connection to
AiM loggers;
oX2 DC Power Connector
(yellow)*to be connected to
the camera one;
oX2 Video RCA Connector
(red)*to be connected to the
camera one.
*The two DC Power and Video RCA cables couples are respectively 4m and 6m long, in order to allow
both front camera and rear camera connection.
3
www.aim-sportline.com Release 1.00 –October 12th 2018
AiM offers the same camera with a more reliable Binder connection (P.N.: XB1ZCAMHD00; Binder connector
pinouts are specified below):
The patch cables available are:
•Single AiM Mirror Camera (6m length) ended
with:
oMale metallic 5pins Binder
connector for connection to AiM
loggers;
oFemale metallic 5pins Binder
connector for Mirror Camera
connection.
•Double AiM Mirror Camera: ended with:
oMale metallic 5pins Binder
connector for connection to AiM
loggers;
oX2 female metallic Binder
connectors: each one must be
used to connect the Mirror
Camera (cable lengths 4m –front
camera –and 6m –rear camera).
4
www.aim-sportline.com Release 1.00 –October 12th 2018
2
Configuration through Race Studio 3
Once the connection has been executed, it is necessary to configure the device, defining a specific event
that causes the camera image displaying. For example, if you wish to turn ON the camera when you
insert the Reverse Gear, these are the steps to follow:
•Open Race Studio 3, connect your system via Wi-Fi or USB and create a new configuration (or modify
an existing one).
•The Gear, of course, is supposed to be one of the available channels. It is possible to obtain it:
oThrough analog sensor, plugging it
into one of the device analog
channels, which must be configured
as expressed on the right (Channels
tab). The “Use reverse gear” box
must be ticked.
oThrough ECU, selecting the
compatible protocol with your
vehicle ECU from the ECU Stream
tab.
5
www.aim-sportline.com Release 1.00 –October 12th 2018
•Open the Trigger Commands tab and click “Add New Command”: select “First Camera Input Page” as
a command to activate when the Gear is equal to “R”.
6
www.aim-sportline.com Release 1.00 –October 12th 2018
3
Settings through AiM device menu
The camera parameters setting must be executed from the device menu directly, as explained below:
•Press “MENU/<<” button.
•Pressing “PREV and “NEXT”, move on the VIDEO IN icon and press “ENTER”.
•The system offers the possibility to set the image format (PAL or NTSC –according to the camera
technical specs), brightness and contrast for each available input.
If no key is pressed, after 5 seconds the menu disappears, showing the camera image in live streaming,
so that it can be better positioned.
Inhaltsverzeichnis
Andere Aim Digitalkamera Handbücher
