Aim RF240/611 Bedienungsanleitung

RC240 3D Mouse Presenter V1.2

Motion Sensor Presenter

RF240/611

RC240 3D Mouse Presenter V1.2

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

RC240 3D Mouse Presenter V1.2

Table of Contents

PACKAGE CONTENTS.................................................................................4

SYSTEM REQUIREMENTS.............................................................................4

RECHARGING THE PRESENTER .....................................................................4

KEY DEFINITIONS ......................................................................................5

USE PRESENTER WITHOUT RUNNING

AIMMASTER™ PRO

SOFTWARE ......................5

INSTALL

AIMMASTER™ PRO

.........................................................................5

START USING PRESENTER...........................................................................6

POWER ON THE PRESENTER ..........................................................................6

POWER OFF THE PRESENTER .........................................................................6

USE MICRO SD CARD .................................................................................6

BASIC MODE ...........................................................................................6

Language .........................................................................................6

Exit .................................................................................................6

Basic Mode Key Definitions ....................................................................7

Virtual Laser Pointer .............................................................................7

Enable/Disable 3D Mouse ......................................................................7

Open/Close Slide Show .........................................................................8

Page Up/Down and Scrolling ..................................................................8

Group Vibrating...................................................................................8

Change 3D Mouse Speed ......................................................................8

Volume Adjust ....................................................................................8

STANDARD MODE ......................................................................................9

Standard Mode Key Definitions ................................................................9

Place Check Mark.............................................................................. 10

Draw Line Mark ................................................................................. 10

Undo or Remove all Marks. .................................................................. 10

Timer Setting ................................................................................... 10

Show Timer ..................................................................................... 11

Plug & Present.................................................................................. 11

Change Laser Icon............................................................................. 12

Group Vibrating................................................................................. 12

LINK PRESENTER WITH RECEIVER .................................................................... 13

ADVANCE MODE ..................................................................................... 13

Change Hotkey Map ........................................................................... 13

Use the Motion keys ........................................................................... 15

CHECK RELEASE NUMBERS.......................................................................... 16

FEATURES ............................................................................................ 17

PRODUCT SPECIFICATIONS ....................................................................... 17

Q & A .................................................................................................. 18

RC240 3D Mouse Presenter V1.2

Package Contents

 Presenter

 Receiver



aimMaster™ Pro

Software CD

(for Microsoft® Windows®

7/Vista/XP), Quick Instruction Guide, and User's Manual

(stored in the Receiver flash memory)

 USB Recharge Cable

 Leather Bag

 Quick Instruction Guide Sheet

System Requirements

 Microsoft® Windows® 7/Vista/XP

 1GB RAM recommended

 CD-ROM drive or DVD-ROM Drive

 USB Port

Recharging the Presenter

Fully charge the Presenter by connecting the miniUSB connector of the

USB cable to the Presenter miniUSB Port. Connect the Presenter with the

computer by the USB cable. The orange light of the LASER key is

flashing. Wait for about 2.5 hours until the light of LASER key changes

to blue; the Presenter is fully charged and ready for use. Click any key will

flash the blue light on the LASER key. The battery can last more than

20 hours for continuous usage. When the battery capacity is low, click any

key will flash the orange light on the LASER key.

RC240 3D Mouse Presenter V1.2

Key Definitions

Use Presenter without running

aimMaster™ Pro

software

Before installing the powerful Presenter Auxiliary Tools –

aimMaster™ Pro

you can use the functions include 3D Air Mouse, Page Up/Down, Group

Vibration alarm, Volume Adjust, etc. However, the Virtual Laser Pointer

can’t work.

Install

aimMaster™ Pro

Insert the CD to your computer. The following windows will pop up.

Follow the instructions to install

aimMaster™ Pro

Double Click the shortcut icon of

aimMaster™ Pro

shown on your desktop to activate

aimMaster™ Pro

The message window will pop up three seconds to

remind you that the

aimMaster™ Pro

is activated.

You will see the

aimMaster™ Pro

icon on the

System Tray.

RC240 3D Mouse Presenter V1.2

Start Using Presenter

The default mode entered is Basic mode that comes with the basic

functions. There are two more operation modes could be used:

Standard Mode: allows you to use Check/Line Marks and other functions.

Advanced mode: allows you to use motions keys for more commends.

Power ON the Presenter

Click the POWER key once to turn on the Presenter. The purple light

on the LASER key flashes once to confirm the ON status.

Power OFF the Presenter

Press and hold the POWER key for 3 seconds until the purple light on

the LASER key is lit. Release the POWER key. The purple light on

the LASER key flashes several times to confirm the OFF status. If the

Presenter is not working for 30 minutes, the Presenter will be turned off

automatically to save the battery power.

Use micro SD Card

Insert a micro SD card into the slot of the Receiver of RC132/611. You

may store the files into this memory.

Basic Mode

Please don’t forget to execute

aimMaster™ Pro

(then the icon is shown on the System Tray),

otherwise the Virtual Laser Pointer isn’t

operable.

Language

Right click the

aimMaster™ Pro

icon ,

and click “Language” tab from pop-up

menu. You will see a dialogue window.

Select the language you prefer.

Exit

aimMaster™ Pro

does not use many

system resources. You may quit this background application to release the

memory when you don’t need it. Right click the icon and click “Exit” from

pop-up menu to close

aimMaster™ Pro

RC240 3D Mouse Presenter V1.2

Basic Mode Key Definitions

Key Action Function

If Presenter is Off, this click turns power to On.

Click If Presenter is On, this click forces Slide Show

(shift F5) or Close Slide Show (ESC)

POWER Press & hold until

Purple LED is On

Turns Presenter to Off.

Click

Enables or Disables 3D Mouse.

If 3D Mouse is enabled, the blue light of

LASER key is flashing.

LASER

Press & Hold Show the Virtual Laser Pointer Icon, (Laser Pointer

icon is changeable, refer to P10)

Click Page up

UP Press & Hold Scroll up

Click Page down

DOWN Press & Hold Scroll down

OK Press & Hold

Turn Presenter clockwise to increase the system

Volume, and turn Presenter counter-clockwise to

reduce the system volume

LEFT Click Mouse Left key, only when 3D Mouse is enabled

RIGHT Click Mouse Right key, only when 3D Mouse is enabled

FEATURE

No function

Flashes Amber: Presenter is Charging

Charging Off: Presenter is fully charged

Flashes Blue: when battery is between 100% ~

40% of full capacity.

LED on

LASER

key Click any key Flashes Amber: when battery is under 40% of full

capacity.

Virtual Laser Pointer

Press and hold LASER key to

activate the emulated Laser

Pointer. Move Presenter will move

the Laser pointer on the screen.

Please refer to the User’s Manual

to select your own virtual laser

pointer icon.

Enable/Disable 3D Mouse

Click LASER key once to enable the 3D Mouse. The blue light on the

LASER key is flashing. The RIGHT and LEFT keys are Mouse Right

and Left button respectively.

Click LASER key once again to disable the 3D Mouse. The blue light

RC240 3D Mouse Presenter V1.2

on the LASER key is turned off. The RIGHT and LEFT keys are NOT

Mouse Right and Left now.

When 3D Mouse is not moving for 30 seconds, the Presenter turns off the

3D Mouse automatically to save the battery power.

Open/Close Slide Show

Clicking POWER key once will open PowerPoint

file to Slide Show or close the Slide Show.

Page Up/Down and Scrolling

Clicking the UP key will initiate a page up operation

while clicking DOWN will initiate a page down.

Press and hold UP or DOWN key, it will execute the

scrolling up or scrolling down feature respectively.

Group Vibrating

If the meeting host wants to

pass some predefined

message (e.g., time end) to

the orator, he may use

another set of Presenter to

send signal to the orator.

The host just presses and

holds the FEATURE key

for more than 2 seconds

until it starts to vibrate, the

Presenter on the orator’s hand will also vibrate for 5 seconds. (Note: the

2nd Presenter should be linked with Receiver in advance. Refer to P13 for

the linking information.)

Change 3D Mouse Speed

Right click the

aimMaster

Pro

icon on the

System Tray. Select the Mouse Speed tab.

Then choose one of the 3 speeds.

Volume Adjust

Press and hold OK key, rotating

Presenter clockwise will enlarge

the volume. Rotating

counter-clockwise will decrease

the volume. The volume meter will

be shown on the right up corner of

the screen.

RC240 3D Mouse Presenter V1.2

Standard Mode

Standard Mode has all the functions

in Basic Mode plus many other useful

features.

Right click the

aimMaster™ Pro

icon

and select Mode from the

pop-up menu. Choose “Standard

Mode”. The icon in System Tray

becomes .

Standard Mode Key Definitions

Refer to the following key definitions for the functions you may use.

Key Action Function

If Presenter is Off, this click turns power to On

Click If Presenter is On, this click forces Slide Show

(shift F5) or Close Slide Show (ESC)

POWER Press & hold until

Purple LED is On

Turns Presenter to Off.

Click

Enables or Disables 3D Mouse.

If 3D Mouse is enabled, the blue light of

LASER key is flashing.

LASER

Press & Hold Show the Virtual Laser Pointer, (Laser Pointer

icon is changeable, refer to P10)

Click

Each click will cycle from Mouse Cursor Check

Mark Line Mark. The cursor changes from

  respectively. The icon on the

System tray will be changed as   .

FEATURE

Press & Hold for 2

seconds

All Presenters vibrate for 5 seconds (the host can

inform time-end to the orator).

In Mouse Cursor operation Page up

Click In Check Mark or Line Mark

operation

Undo previous

mark

Press & Hold Scroll up

In Mouse Cursor operation Page down

Click In Check Mark or Line Mark

operation

Clear all marks

DOWN

Press & Hold Scroll down

Click

In Check Mark operation, a Check Mark is

placed.

Press & Hold

In Line Mark operation, a red line is drawn,

the longer time you press, the longer red line

extends to the right.

RC240 3D Mouse Presenter V1.2

Turn Presenter clockwise to increase the system

Volume, and turn Presenter counter-clockwise to

reduce the system volume

Mouse Left key, only when 3D Mouse is enabled.

LEFT Click When 3D Mouse is disabled, the Timer will be

shown on the right corner of the screen.

RIGHT Click Mouse Right key, only when 3D Mouse is

enabled.

Flashes Amber: Presenter is charging

Charging Off: Presenter is Fully charged

Flashes Blue: when battery is between

100%~40% of full capacity.

LED on

LASER

key Click any key Flashes Amber: when battery is under 40% of full

capacity.

Place Check Mark

You can place red Check Marks

and draw Line Marks on the

screen to emphasis the

important parts.

Click LASER key once to

activate 3D Mouse. Click

FEATURE key once to enable

the Check Mark. Move Presenter

to control the position of the

Check Symbol cursor. Each

click of OK key will place a

Check Mark on the screen.

Draw Line Mark

Click FEATUER key again to enable the

Line Mark. Press and hold OK key to

draw the red line. The longer time you

press, the longer red line extends to the

right.

Undo or Remove all Marks.

Press UP key to undo the previous

mark or DOWN key to clear all the

marks.

Timer Setting

Right click the

aimMaster

Pro

icon on

Inhaltsverzeichnis

Andere Aim Digitaler Präsentator Handbücher

Aim

Aim RC612 Bedienungsanleitung

Beliebte Digitaler Präsentator Handbücher anderer Marken

Edirol

Edirol RG-100 Bedienungsanleitung

Hama

Hama Como Bedienungsanleitung

Dukane

Dukane AV-P1000 Bedienungsanleitung

Canon

Canon PR3 Bedienungsanleitung

VSON

VSON N81 Bedienungsanleitung

Samsung

Samsung UF-130DX Bedienungsanleitung

Targus

Targus Multimedia Bedienungsanleitung

Edirol

Edirol PR-50 Betriebsanleitung

x-pointer

x-pointer IMAGE POINTER XPM170Y Bedienungsanleitung

Acrobak

Acrobak BLP-305 Bedienungsanleitung

Targus

Targus Mac AMP11 Bedienungsanleitung

Edirol

Edirol PR-50 Bedienungsanleitung

Samsung

Samsung SDP-850 Bedienungsanleitung

Dukane

Dukane DV-P303A Bedienungsanleitung

RemotePoint

RemotePoint Presenter Global Bedienungsanleitung

Kensington

Kensington Wireless Presenter with Laser Pointer Betriebsanleitung

NEC

NEC DS1-MP10RX2 Betriebsanleitung

Logitech

Logitech R800 - Professional Presenter Presentation Remote... Bedienungsanleitung