Aimco UEC-4800EPL Bedienungsanleitung
UEC-4800EPL Upgrade Kit
INSTRUCTION MANUAL
DISASSEMBLY OF UEC-4800
1
2
3
4
5
BILL OF MATERIALS
PART NUMBER QTY DESCRIPTION
UEC-4800 0 Torque Controller
1. Remove the four screw on both sides of the UEC-4800.
2. Remove the two screws that hold the front panel to the UEC-4800.
3. Remove the cover of the UEC-4800.
4. Push the front panel free from its connector and place to the side.
5. Remove the two screws on both sides that hold the board in place.
6. Move the board back and to the side to expose the ground rail.
6
WEAR ESD GROUND STRAP WHEN HANDLING PCB
BILL OF MATERIALS
PART NUMBER QTY DESCRIPTION
UEC-4800 0 Torque Controller
UEC-4800EPL-UPGRAD 1 Kit
1. Find the TB1 connector, unplug it, and cut the wire tie holding it in place.
2. Install the two green w/yellow striped wires from power interface cable to the ground rail.
3. Connect the power interface cable to the TB1 connector.
4. Connect the power cable from the UEC to the plug on the PCB of the power interface cable.
5. Move the board to the UEC back and install the four screws to secure it in place.
WIRING THE TOP COVER TO THE UEC-4800
1
2
INTERFACE
CABLE
5
WEAR ESD GROUND STRAP WHEN HANDLING PCB
3
POWER
INTERFACE CABLE
4
POWER
INTERFACE CABLE
INSTALLING THE TOP COVER ASSEMBLY OF THE UEC-4800
BILL OF MATERIALS
PART NUMBER QTY DESCRIPTION
UEC-4800 0 Torque Controller
UEC-4800EPL-UPGRAD 1 Kit
1. Install the front panel back in to the board on the UEC, secure tightly.
2. Install the top cover assembly to the UEC and reinstall the eight screws that hold the cover in place, making sure not to pinch the wires coming
out of the back.
3. Install the two screws that hold the front panel in place.
WEAR ESD GROUND STRAP WHEN HANDLING PCB
1
2
3
INSTALLING THE DATA AND I/O CABLE TO THE UEC
BILL OF MATERIALS
PART NUMBER QTY DESCRIPTION
UEC-4800 0 Torque Controller
UEC-4800EPL-UPGRAD 1 Kit
1. Connect the UEC null modem cable to the DB9 PC plug on the back of the UEC.
2. Connect the I/0 cable to the I/O terminal block top row on the back of the UEC, black wire to COM (upper)/IN COM, red wire to LS1/IN6,
white wire to RESET/IN3, green wire to work A/IN4 and yellow wire to work B/IN5
3. Connect the red fork with the two blue wires to the lower COM and the other red fork and the black wire to the top COM. Install male bullet
(26376) into the bullet connector on the blue wire. Bundle wires, zip tie, and reinstall the I/O cover.
WEAR ESD GROUND STRAP WHEN HANDLING PCB
1
2
I/O CABLE
3
FORK CONNECTOR
BULLET CONNECTOR
3
3
BULLET CONNECTOR
NULL MODEM CABLE
INSTALLING THE PROFIBUS TO THE UEC
BILL OF MATERIALS
PART NUMBER QTY DESCRIPTION
UEC-4800 0 Torque Controller
UEC-4800EPL-UPGRAD 1 Kit
1. Connect the UEC PFB serial cable to the Profibus Slave Card and tighten the two screws on the connector. You will need to set the two pots of
the Profibus Slave Card. Set MSD to zero and set LSD to eight.
WEAR ESD GROUND STRAP WHEN HANDLING PCB
PFB SERIAL CABLE
PROFIBUS SLAVE CARD
Revision History: Revision Date: 11/04/2013 Document Change Log: Initial Release
AIMCO CORPORATE HEADQUARTERS AIMCO CORPORATION DE MEXICO SA DE CV
10000 SE PINE STREET AVE. CRISTOBAL COLON 14529
PORTLAND, OREGON 97216 CHIHUAHUA, CHIHUAHUA. 31125
PHONE: (503) 254–6600 MEXICO
TOLL FREE: 1-800-852-1368 PHONE: (01-614) 380-1010
FAX: (01-614) 380-1019
LIT-MAN175 REV. 07/2020
PRINTED IN USA ©2020 AIMCO
Inhaltsverzeichnis
Andere Aimco Controller Handbücher
Aimco
Aimco AcraDyne Gen IV Handbuch
Aimco
Aimco AcraDyne iBC-Z Bedienungsanleitung
Aimco
Aimco ArcaDyne IEC4W Bedienungsanleitung
Aimco
Aimco AcraDyne Gen IV Bedienungsanleitung
Aimco
Aimco UEC-4800EX Bedienungsanleitung
Aimco
Aimco AcraDyne iPC Bedienungsanleitung
Aimco
Aimco AcraDyne Gen IV Bedienungsanleitung
Aimco
Aimco AcraDyne Stücklistenhandbuch
Aimco
Aimco AcraDyne Gen IV iAC Bedienungsanleitung
Aimco
Aimco iEC Bedienungsanleitung
