Aimco Auditor Bedienungsanleitung
Quick Start Guide
One Too Moment Alpha Torque Wrench
PO Box 16460, Portland OR 97292-0460
1-800-852-1368 • (503) 254-6600
www.aimco-global.com
2 www.aimco-global.com • (800) 852-1368 • (503) 254-6600
This guide provides steps to run the Moment Alpha wrench and controller, and initiate and execute a
test strategy.
Equipment/Software
• CPSKV00 – Wrench Handle with battery
• Wrench handle battery pack
• Portable or Bench mount controller
• Joint Kit to run a sequence program effectively
Hardware Setup
• Power ‘on’ the bench mount or portable tablet
• Install battery pack into the wrench handle
• Power ‘on’ CPSKV00 Wrench Handle – No attachments installed
Controller Interface
Image 1 shows the ‘main screen and when selecting the menu button or select sequence, operator
will navigate back to the main screen by using the return arrow symbol
embedded into the
controller/tablet
Moment Alpha Torque Wrench Quick Start Guide
Touch Screen to
activate analyzer
Menu
button
www.aimco-global.com • (800) 852-1368 • (503) 254-6600 3
1. Sethandleonaatsurfacewithout
attachments.
2. Touch Reconnection on controller
to sync it with the wrench handle.
– Press ‘Ok’ to verify
Synching is
complete when
the Reconnection
image is replaced
by the image of a
wrench handle on
the screen.
3. Touch the menu button to
move to the setup menu.
Tool Testing
1. Login is required to develop a sequence.
Select Sequence from the setup menu. This
opens the Sequence Setup screen.
2. Touch the pencil icon, which takes you to
the User name screen.
3. Log in using default user name and
password.
Sync Tool with Controller
Login
Default User Name: admin
Default Password: admin
Quick Start Guide
4 www.aimco-global.com • (800) 852-1368 • (503) 254-6600
Sequence is a strategy – either Production or
Quality. Access to these sequence options is
dependent on the level of software available in
the controller. See the OneToo Moment Alpha
User Manual (LIT-MAN271) for steps to locate and
identify the software version installed on your
controller.
1. Select
to create a sequence name.
2. Select to create a program.
Each strategy has 3 program options.
Production Programs
• Torque Control & Angle Monitoring
• Torque Control
• Angle Control & Torque Monitoring
Quality Programs
• Re-tight Mode
• Target Angle
• Residual Torque
Select the appropriate program. You can
develop more than one program per strategy.
3. Use return arrow key to save sequence/
program and return to the main screen.
Set up a Sequence & Program
Production Program Options
Quality Program Options
Quick Start Guide
4. When the image
replaces the pencil
symbol on this page, this is an indication that
you are logged in.
You now have access to:
Sequence (S+) Program (P+)
www.aimco-global.com • (800) 852-1368 • (503) 254-6600 5
1. Select Torque control & Angle monitoring from the
production program options menu.
Example: Program Torque Control and Angle Monitoring
Quick Start Guide
2. Populate program parameters
with the following required
details:
• Target Torque (min/max will
default to 10% of target)
• Min/Max Angle
• Batch Count
Other inputs are optional and
willinuencetestresults.
6 www.aimco-global.com • (800) 852-1368 • (503) 254-6600
At any time during the program, the
operator can stop the execution by
touching the located on the top left
corner of the screen.
Edits to the program can be made:
• Reset target torque
• Renethemin/maxtorquewindow
• Renetheanglewindow
• Adjust the batch count
Additional edits are available as well. See
LIT-MAN271 for more options.
Quick Start Guide
4. From the main screen, touch Select
sequence and a menu will appear to
allow you to choose your sequence.
5. Touch the sequence name to begin
testing.
Note: Check the Automatic Sequence box
on the Sequence Set screen when you assign
multiple programs to one sequence. This will run
the programs sequentially during the rundown.
3. Oncethetestparametersaredened,use
return arrow key to exit. This will take you
back to the main screen.
www.aimco-global.com • (800) 852-1368 • (503) 254-6600 7
Results
Touch the menu tab.
Select the Last results.
View rundowns
• Production
(tightening)
• Quality
View Traces
Touch the menu tab.
Select Last Curves.
Quick Start Guide
Use return arrow key to return to the main screen.
LIT-MAN270 Rev. 08/30/2018
Printed in USA ©2018 AIMCO
CORPORATE HEADQUARTERS
10000 SE Pine Street
Portland, Oregon 97216
Phone: (503) 254–6600
Toll Free: 1-800-852-1368
AIMCO CORPORATION DE MEXICO SA DE CV
Ave. Cristobal Colon 14529
Chihuahua, Chihuahua. 31125
Mexico
Phone: (01-614) 380-1010
Fax: (01-614) 380-1019
AIMCO EUROPE
Dibao Plaza Avenida Río Gallo, 431
19174 Galápagos - Guadalajara
Spain
Phone: +34 673 34 99 25
AIMCO CHINA
Room 607, No. 3998 Hongxin Rd
Minhang District, Shanghai
China
Phone: 0086-21-34319246
Fax: 0086-21-34319245
AIMCO SOUTH AMERICA
Calle Congreve No 800. Escobar
El Aromo. L207
Provincia de Buenos Aires
Argentina
CP: 1625
Phone: +54 9 11 3341 0543
AIMCO SOUTH KOREA
B-1213, 167, Songpa-Daero
Songpa-Gu, Seoul 05800
South Korea
Phone: 0082-2-2054-8930
Cell: 0082 10 9804 8905
WWW.AIMCO-GLOBAL.COM
Andere Aimco Elektrowerkzeuge Handbücher
Aimco
Aimco UAT Series Betriebsanleitung
Aimco
Aimco AcraDyne 1000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne Gen III 3000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne HT Series Bedienungsanleitung
Aimco
Aimco UOW Series Betriebsanleitung
Aimco
Aimco AcraDyne Gen III 3000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne ABETP Cordless XT Series Bedienungsanleitung
Aimco
Aimco AcraDyne Gen 4 HT Series Bedienungsanleitung
Aimco
Aimco Signature Series Bedienungsanleitung
Aimco
Aimco AcraDyne AcraDrive 2000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne Gen IV 2000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne Gen III 2000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne Gen III 2000 Series Bedienungsanleitung
Aimco
Aimco AcraDyne AB-CTA Bedienungsanleitung
Aimco
Aimco AcraDyne Phoenix II Bedienungsanleitung
Aimco
Aimco AcraDyne HT ABG Series Bedienungsanleitung
Aimco
Aimco AcraDyne HT Series Bedienungsanleitung
Aimco
Aimco URW Series Betriebsanleitung
Aimco
Aimco UBX-T Series Bedienungsanleitung
Aimco
Aimco PISTOL Bedienungsanleitung
