Aiphone JO-1FD Bedienungsanleitung
JO-1FD
EXPANSION MONITOR STATION
INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
MANUAL DE INSTALACIÓN Y OPERACIÓN
INSTALLATIE- EN BEDIENINGSHANDLEIDING
MANUALE D'INSTALLAZIONE E USO
INSTALLATIONS- UND BEDIENUNGSANLEITUNGHANDBUCH
FK1898 A P0713KD 55061
HANDS-FREE COLOR VIDEO INTERCOM EXPANSION MONITOR STATION
POSTE DE SURVEILLANCE D’EXTENSION D’INTERPHONE VIDÉO COULEUR MAINS LIBRES
MONITOR SECUNDARIO DE INTERCOMUNICACIÓN CON VÍDEO A COLOR MANOS LIBRES
HANDENVRIJE UITBREIDINGSBEWAKINGSPOST VOOR KLEURENVIDEOFOON
POSTAZIONE MONITOR SUPPLEMENTARE VIDEOCITOFONO A COLORI CON VIVAVOCE
FREISPRECH-FARBVIDEO-ERWEITERUNGSMONITORSTELLE
JO-1FD
Thank you for selecting Aiphone for your communication and security needs. Please read this manual carefully for proper system
operation. For future reference, keep manual in a safe place.
EnglishFrançaisEspañolNederlandsItalianoDeutsch
2
PRECAUTIONS
Prohibited Do not dismantle unit Keep unit away from water General precautions
WARNING
Negligence could result in death or serious injury.
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Keep the unit away from water or any other liquid.
Fire or electric shock could result.
3. High voltage is present internally. Do not open the case.
Electric shock could result.
4. Do not connect any non-specied power source to the +, - terminals. Also, do not
install two power supplies in parallel to a single input. Fire or damage to the unit
could result.
5. Do not use power supply with a voltage other than specied.
Fire or electric shock could result.
6. Do not put any metal or ammable material into the unit through the openings.
Fire, electric shock, or unit trouble could result.
7. The unit must be installed and wired by a qualied technician.
CAUTION
Negligence could result in injury or damage to property.
1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.
2. When mounting the unit on a wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.
3. Before turning on power, make sure wires are not crossed or shorted. Fire or
electric shock could result.
4. Do not install the unit in locations subject to frequent vibration or impact. It may
fall or tip over, resulting in damage to the unit or personal injury.
5. For power supply, use Aiphone power supply model specied for use with system.
If non-specied product is used, re or malfunction could result.
6. Do not put anything on the unit or cover the unit with cloth, etc.
Fire or unit trouble could result.
7. Do not install the unit in any of the following locations. Fire, electric shock, or unit
trouble could result.
* Places under direct sunlight or near heating equipment that varies in temperature.
* Places subject to dust, oil, chemicals, hydrogen sulde (hot spring).
* Places subject to moisture and humidity extremes, such as bathrooms, cellars,
greenhouses, etc.
* Places where the temperature is quite low, such as inside a refrigerated area or
in front of an air conditioner.
* Places subject to steam or smoke (near heating or cooking surfaces).
* Where noise generating devices such as dimmer switches or inverter electrical
appliances are closeby.
8. Do not apply high pressure on the screen. If fractured, injury could result.
9. If the LCD is punctured, do not allow skin contact with the liquid crystal inside.
Inammation could result.
* If liquid crystal is ingested, immediately gargle with water and seek medical
attention.
* If contact with the eyes or skin occurs, clean with pure water and seek medical
attention.
GENERAL PRECAUTIONS
1. Keep the unit more than 1m (3.3') away from radio or TV set.
2. Keep the intercom wires more than 30cm (12'') away from AC 100-240V wiring. AC
induced noise and/or unit malfunction could result.
3. Comply with all third party manufacturing specications that will be used with this
system (sensors, door releases, etc.).
4. If the unit is down or does not operate properly, unplug the power supply.
5. When wall-mounted, the top of the unit may darken. This does not indicate a
malfunction.
6. The unit case may become warm with use, but this is not a unit malfunction.
7. If it is used close to a cellular phone, the unit may malfunction.
8. The unit can be damaged if dropped. Handle with care.
9. The unit will not work during power failure.
10. In areas where broadcasting station antennas are close by, the intercom system may be
affected by radio frequency interference.
11. The unit is designed for indoor use only. Do not use at outdoor locations.
12. This product, providing door release, should not be used as a crime prevention device.
13. Please note the LCD panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its image elements always lit or not lit at
all. This is not considered a unit malfunction.
14. Environmental sound around the unit may hinder smooth communication, but this is
not a malfunction.
15. At night, due to reduced lighting on the object, the screen sees more noise and faces
become more difcult to see, but this is not a malfunction.
16. For hands-free communication:
If you stand too far away, it may be difcult for the other person to hear the
communication.
17. If there are loud noises around the unit (such as music playing or children crying), the
sound may break up and be difcult to hear.
18. During communication, if you speak before the other person has nished talking, your
voice may not come through clearly.
Communication will proceed smoothly if you wait until the other person has nished
before speaking.
19. At a gate or porch illuminated by a uorescent lamp, the image may vary, but this is
not a malfunction.
20. The outline of video images displayed by the video door station may differ from that
of the actual person(s) or background, but this is not a malfunction.
21. When the unit’s screen is illuminated with strong light, the image looks white or
silhouetted, but this is not a malfunction.
NOTICES
* We will under no conditions be liable for damage occurring due to the inability to
communicate due to malfunctions, problems, or operational errors in this product.
* We will under no conditions be liable for any damages or losses resulting from this
product’s contents or specications.
* This manual was created by Aiphone Co., Ltd., all rights reserved. Copying, in part
or in whole, this manual without prior permission from Aiphone Co., Ltd. is strictly
forbidden.
* Please note that images and illustrations depicted in this manual may differ from the
actual ones.
* Please note that this manual may be revised or changed without prior notice.
* Please note that product specications may be changed for the sake of improvement
without prior notice.
* This system is not intended for life support or crime prevention. It is a supplementary
means of conveying information. Aiphone will under no conditions be liable for loss of
life or property which occurs while the system is being operated.
* Lighting adjustments are made automatically by the door station. Adjustment results
may vary depending on installation environment.
English Français Español Nederlands Italiano Deutsch
3
FEATURE AND SYSTEM EXAMPLE
Entrance
Living room on 2nd oor
Living room
Door station
• Calls the master monitor station
and expansion monitor station.
• Pushing the [Call] button at night
lights the White light LED.
Expansion monitor station
• Responds to a call from the door station.
• Monitoring the entrance.
• Can be used with a call extension speaker.
Master monitor station
• Responds to a call from the door station.
• Monitoring the entrance.
• Can be used with a call extension speaker.
Call extension
speaker
Call extension
speaker
EnglishFrançaisEspañolNederlandsItalianoDeutsch
4
PART NAMES Remove protective film before use.
JO-1FD
Color LCD screen
Displays camera images during door
station call-ins, communication with door
station, and door station monitoring Status LED (orange)
Indicates the current status of this station by lighting up or blinking.
On: During communication sending, while the door release button is
being pressed, or while the option button is being pressed
Flashing: During communication reception in the PTT mode, during
short detection or during mute
Option button
To activate/trigger external device
Door release button
Unlocks door
Talk/off button
Starts or ends communication.
Speaker
Call tones, sounds from a door station.
RESET button
Press this button to reboot this
station when it is not responding.
Microphone
Sends sounds from this station
to other stations.
[Bottom View]
Monitor button
Monitor a door station
Volume control button
[During standby]
Adjust the calling volume.
Volume adjustment range: (mute), -
[During communication or monitoring]
Adjust the communication volume.
Volume adjustment range: -
Screen brightness control button
Adjusts LCD screen brightness
Brightness adjustment range: -
PACKAGE CONTENTS
NOTES:
• Mounting and Wood mounting
screws not included
Manual
JO-1FD
English Français Español Nederlands Italiano Deutsch
5
INSTALLING EXPANSION MONITOR STATION
When installing the expansion monitor station with the master monitor station
A
When adding the expansion master monitor station to an existing system
B
Installation procedures
Install and connect the expansion monitor station between the master monitor station and the door station.
→ See Procedure A below.
→ See Procedure B below.
When adding the expansion monitor station, remove the master monitor station and install the expansion monitor station to where
the master monitor station has been installed. Install the master monitor station so that the expansion monitor station is between the
master monitor station and the door station.
Door station Master monitor stationExpansion monitor station
Door station
Add Move to new place
Master monitor stationExpansion monitor station
*1 Refer to WIRING on page 8 for wiring and connection with optional accessories.
*2 When disconnecting wires from the master monitor station, label or mark wires to identify where each wire is connected.
*3 Mounting brackets used for the master monitor station can be used for the expansion monitor station.
Procedure
B
Procedure
A
Check the wiring diagram. *1
Turn on power at the master monitor station and the expansion monitor station to check for normal operation.
Install the door station.
Install the expansion monitor station.
Install the master monitor station.
Install the expansion monitor station to where
the master
monitor
station has been installed. *3
Install the master monitor station to a new place.
Turn off the power of the master monitor station
to remove it. *2
EnglishFrançaisEspañolNederlandsItalianoDeutsch
6
INSTALLATION
Wiring method, wiring distance
JO-1FD
JO-DA
JO-DV
JO-DVF
A D
BC
IER-2
PS18
JO-1MD
CIER-2
: PS-1820, PS-1820S, PS1820UL, PS-1820D
Ø 0.65 mm 22 AWG Ø 0.8-1.2 mm 20-16 AWG
A50 m 165'100 m 330'
B 5 m 16'10 m 33'
C 50 m 165'150 m 495'
D 50 m 165'100 m 330'
Mounting locations
In direct sunlight Avoid installing the expansion monitor
station in a concave space of a
wall to prevent disconnection
of communication
Allow at least 15 cm (6") above
and 25 cm (9") below center of
the mounting
bracket for
installation
of the station
15 cm (6
"
)
or more
ab c
25 cm (9
"
)
or more
Do not install expansion monitor station in any of the following locations where lighting or the ambient environment could impact
the display on the video monitor.
Cable
Use PE (polyethylene)-insulated PVC jacket cable.
Parallel or jacketed 2-conductor, mid-capacitance, non-shielded
cable is recommended.
Never use individual conductors, twisted pair cable, or
coaxial cable.
English Français Español Nederlands Italiano Deutsch
7
MOUNTING
JO-1FD
83.5mm (3-5/16")
8mm
(3/8")
Wires
3-gang box
Mounting bracket
(attached to the unit with shipment)
Mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Mount the unit on the
mounting bracket.
3
Fasten the mounting
bracket to the wall
1
21.Press release button to insert or remove wire.
2.Insert wire into the terminal.
<Back wiring>
When the wiring is not coming through the wall, the wires can be routed to the top or bottom of the unit. Remove a cable inlet plate on the
upper part of the unit to allow passage of the wiring into the unit.
92mm (3-5/8")
83.5mm
(3-5/16")
Mounting bracket
(attached to the unit with
shipment)
Wood mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Wires
Remove cable inlet plate
<Surface wiring>
EnglishFrançaisEspañolNederlandsItalianoDeutsch
8
1
E
A1 A2
2
NP
2
NP
2
NP
PS-1820D
IER-2
JO-DV JO-DVF
IN 230V~ 50/60Hz
N
L
LN
-
++
-
+
-
230V AC
50/60Hz
18V DC 2A
JO-DA
1
E
2
NP
IER-2
2
P
-
+
2
P
2NP
PS18
PS18
: Power supply
JO-1FD JO-1MD
PS-1820
PS-1820S
PS-1820UL
100V - 240V
50/60Hz
18V DC 2A
Door release
An EL-12S (AC 12 V, 0.125 A, DC 12 V, 0.2 A) or
equivalent part and a separate AC transformer (or
power supply) are required.
Door release contact: AC/DC 24 V, 0.5 A
(Minimum contact: 100 mV DC, 0.1 mA)
(N/O dry closure contact L).
*Run separate cables for audio/video and door release.
Electric door
strike AC transformer
Master monitor stationExpansion monitor station
(To optional units)
(AC/DC 24V, 0.5A N/O dry closure contact)
(Minimum contact: 100mV DC, 0.1mA)
(To optional units)
(AC/DC 24V, 0.5A N/O dry closure contact)
(Minimum contact: 100mV DC, 0.1mA)
Video door station
Call extension speaker IER-2
EL-12S
Presence of sound from IER-2
NP: Non-polarized
P: Polarized
WIRING
Insert wires securely into each terminal as shown.
Call tone from door station.
Without grounding, the units may not operate
normally.
English Français Español Nederlands Italiano Deutsch
9
OPERATIONS
Answering a door call
1Press and hold for 2 seconds or more.
After approx. 2 seconds beep sounds, PTT mode is engaged.
• If is pressed briefly, PTT mode is not engaged.
2When communicating, keep pressed. To hear the caller’s voice,
release .
Status LED lights when you talk, and flashes slowly as you listen to caller
(or hear outside sounds).
NOTES:
• It is not possible to switch back to hands-free mode (from PTT mode
during communication).
For loud outdoor areas, use Press-to-Talk mode (PTT)
1Push Call button.
2The call tone sounds, an image appears on screen.
• The screen turns off after approx. 45 seconds if not answered.
3Push , and after the beep, communicate hands-free (hands-free mode).
4After finishing communication, push and communication
will end after the beep.
NOTES:
• Communication ends automatically after approx. 1 minute.
• The communication volume can be adjusted during the monitoring or
the communication by pressing .
There are three communication volume setting to cycle through:
[
] (Minimum), [
] (Medium), and [
] (Maximum). The current
volume level is displayed on the screen and disappears in approx. 5
seconds. The default setting is [
] (Medium).
• Even when the expansion monitor station has responded to a call from
the door station, the master monitor station displays the image for
approx. 45 seconds.
• While either of the expansion monitor station or the master monitor
station is displaying an image, the White light LED of the door station
remains on at night.
• Pushing of the master monitor station while the expansion monitor
station is communicating with the door station results in three-way
communication.
• The master monitor station and the expansion monitor station cannot call
or communicate each other.
• Pushing of the master monitor station while the expansion monitor
station is communicating with the door station can display the entrance
and enable monitoring of the communication.
After 2 seconds or more
EnglishFrançaisEspañolNederlandsItalianoDeutsch
10
Monitoring door station
1Push in standby mode.
2The video image from the door station and the incoming audio is heard.
If you do not push , the caller will not hear sounds from the inside
station.
3Push to end monitoring.
NOTES:
• To talk to door station during monitoring, momentarily push . This allows communication with door station.
• The monitoring turns off automatically after approx. 1 minute.
• Pushing of the master monitor station while the expansion monitor station is used to monitor the entrance enables monitoring the
entrance with both the master monitor station and the expansion monitor station.
• Pushing of the master monitor station while the expansion monitor station is used to monitor the entrance enables communication
between the master monitor station and the door station. The expansion monitor station continues monitoring and the communication
come from stations.
• Pushing of the expansion monitor station while the master monitor station is used to monitor the entrance enables communication
between the expansion monitor station and the door station. The master monitor station continues monitoring.
Night illumination
<When the white light LED is lit up during monitoring door station>
When is pushed during monitoring door station, the White light LED will
light up.
When monitoring door station ends, the White light LED will turn off.
NOTES:
• The door station evaluates lighting conditions to automatically turn on the
white light LED when necessary.
At night, the door station White light LED lights up during calling or monitoring door station.
Activating door release
1Press .
2Door release is activated and door can be opened.
During release: Status LED lights.
Adjust call tone volume
1Push in standby mode to adjust call tone volume and display the
volume level.
2Push until the desired call tone volume level is heard.
NOTES:
• There are four call tone volume settings to cycle through: [ ] (Mute), [
] (Minimum) - [
] (Maximum).
The current volume level is displayed on the screen and disappears in approx. 5 seconds. The default setting is [
] (Medium).
Andere Handbücher für JO-1FD
1
Inhaltsverzeichnis
Andere Aiphone Monitor Handbücher
Aiphone
Aiphone JO-1MDW Bedienungsanleitung
Aiphone
Aiphone MY-CU-PH/A Bedienungsanleitung
Aiphone
Aiphone JOS-1A2 Bedienungsanleitung
Aiphone
Aiphone MYH-CU Bedienungsanleitung
Aiphone
Aiphone PanTilt MY Series Bedienungsanleitung
Aiphone
Aiphone MFH-U Bedienungsanleitung
Aiphone
Aiphone JO-1MDW Bedienungsanleitung
Aiphone
Aiphone MY-CU-PH/B Bedienungsanleitung
