AIPTEK 3D i2 Bedienungsanleitung
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is
subjected to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Move the equipment away from the receiver.
-Plug the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/television technician for additional suggestions.
<RXDUHFDXWLRQHGWKDWDQ\FKDQJHRUPRGL¿FDWLRQVWRWKHHTXLSPHQWQRWH[SUHVVO\DSSURYHG
by the party responsible for compliance could void Your authority to operate such equipment.
If the time arises to throw away your product, please
recycle all the components possible.
Batteries and rechargeable batteries are not to be
disposed in your domestic waste! Please recycle
them at your local recycling point.
Together we can help to protect the environment.
Welcome:
Dear user, thank you for purchasing this product.
Much investment in time and effort has gone into its development, and it is our hope
that it will give you many years of trouble-free service.
Extra notice regarding 3D viewing:
1. To view 3D display and receive 3D effects well, the viewer should be positioned to face the
center of the screen at around 30 cm distance and not having a steep viewing angle.
2. Viewing in 3D mode may cause dizziness or even perceptive after effects, disorientation,
and eye strain. It is recommended that viewers take frequent breaks to alleviate the
likelihood of these effects. If you have any of the above symptoms, immediately cease
usage of the 3D display of this device and do not resume until the symptoms have receded.
'RQRWXVHWKH5HG&\DQ*ODVVHVIRUDQ\SXUSRVHRWKHUWKDQYLHZLQJUHGF\DQ'¿OHV
Wearing the Red/Cyan Glasses for any other purpose (such as general spectacles,
sunglasses, protective goggles, etc.) may cause harm to you or weaken your eyesight.
<RXQJFKLOGUHQYLHZLQJ'¿OHVVKRXOGDOZD\VEHDFFRPSDQLHGE\DGXOWV,WLVQRW
recommended to give this device into the hands of young children.
Safety Notice:
1. Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided.
2. Avoid all contact with water, and dry hands before using.
3. Do not expose the camcorder to high temperature or leave it in direct sunlight. Doing so may
damage the camcorder.
4. Use the camcorder with care. Avoid pressing hard on the camcorder body.
5. For your own safety, avoid using the camcorder when there is a storm or lightning.
'RQRWXVHEDWWHULHVRIGLIIHUHQWVSHFL¿FDWLRQV'RLQJVRPD\OHDGWRWKHSRWHQWLDOIRUVHULRXV
damage.
7. Remove the battery during long periods between usage, as a deteriorated battery may affect
the functionality of the camcorder.
8. Remove the battery if it shows signs of leaking or distortion.
9. Use only the accessories supplied by the manufacturer.
10. Keep the camcorder out of the reach of infants.
11. Risk of explosion if battery is replaced by an incorrect type.
12. Dispose of used batteries according to the instructions.
The 3D display technology used
in this product:
This product utilizes the “Parallax Barrier” 3D
technology. A parallax barrier is a device that
allows a liquid crystal display (LCD) to show
a stereoscopic image without the need for the
viewer to wear a pair of 3D glasses. Placed
in front of the normal LCD, a parallax barrier
consists of a layer of material with a series
of precision slits, allowing each eye to see a
different set of pixels, thus creating a sense of
depth and 3D effect through parallax.
Parallax Barrier
Pixels
Right
Left
Right eye
Left eye
Getting Started................................................................ 1
Product overview .................................................................................. 1
Loading the battery............................................................................... 2
Charging the battery ............................................................................. 2
Powering on or off / Using a memory card ........................................... 3
Setting language................................................................................... 3
Reading screen icons ........................................................................... 3
Basic Operations............................................................ 4
Recording a video clip .......................................................................... 4
Taking a photo ...................................................................................... 4
Playback ............................................................................................... 5
'HOHWLQJ¿OHV ......................................................................................... 6
Menu operations................................................................................... 6
Menu items ........................................................................................... 6
File management on PC....................................................................... 7
Connecting to HDTV............................................................................. 8
Appendix ......................................................................... 9
Battery life / Capacity table................................................................... 9
Troubleshooting .................................................................................... 9
6SHFL¿FDWLRQV........................................................................................ 10
Table of Contents
1
1
Getting Started
2
3
12
4
5
6
17
8
9
10
11
15
16
18
1Power button -
Press to turn on;
long-press to turn off
2HDMI port
3SD/SDHC card slot
42D/3D display
5Record button
6Shutter button
7Speaker
82D/3D button -
Switch between 2D/3D
mode
95-way joystick -
5-way: up/down/left/right/
enter
Enter: OK or Playback
10 Delete button
11 Battery charge LED
indicator
12 USB switch -
Slide downward to use
the USB connector
13 Right lens -
For 2D and 3D capture
14 Left lens -
For 3D capture
15 Microphones
16 Battery cover
17 USB connector
18 Tripod socket
19 Hang strap holder
Product overview
7
13 14
19
2
Loading the battery
1Press the “3D” mark and
then, while pressing,
pull the battery cover to
remove it.
2Place the battery into
the compartment. Align
the + and - metallic ends
carefully.
3Replace the
battery cover.
Charging the battery
1Slide the USB switch downward
to reveal the USB connector.
2Connect the USB connector to a USB port of
a powered PC and the charge will begin. Use
an extension cable if necessary.
The LED light turns amber when the charge is
in progress. After the charge is complete, the
LED light will turn green.
Before charge:
3RZHURIIWKHXQLW¿UVWDQGPDNHVXUHWKH/LLRQ
battery is installed.
Make sure your PC is powered on during the
charge.
It is recommended to charge the battery for at
OHDVWKRXUVEHIRUHWKH¿UVWWLPHXVDJH
LED light
Note that the + and - metallic contacts must be aligned with the corresponding contacts
in the compartment.
1.1
1.2
3
Powering on or off / Using a memory card
Press the power button to power on the unit.
Press and hold down for 2 seconds to turn off
the unit.
If the unit cannot be powered on, please check the followings:
1) The battery is correctly loaded;
2) The loaded battery has enough power.
Insert a SD/SDHC card (sold separately) into the slot
until it clicks into place. To remove the card, push the
card to release it and then pull it out gently.
Reading screen icons
03:27:50
Battery life:
: full
: moderate
: low
: empty
Zoom bar
Remaining
recording time
Recording mode:
: 2D
: 3D
Menu button indicator
(Push the joystick to
the right to enter the
Menu setting)
Preview mode icon
Storage:
: internal
: memory card
Setting language
1Push the Joystick to the right ( ) to bring up menu.
2Select the “Language” item and Press OK ( ).
3Move the Joystick up/down ( ) to select your local
language. Press the OK button ( WRFRQ¿UP
5-way Joystick
4
1Press the Record button ( ) to start the recording.
2During recording, you can move the Joystick up/down
() to zoom in/out the image. You can also press the
OK button ( ) to pause or resume the recording.
3Press the Record button ( ) again to stop the
recording.
Basic Operations
Recording a video clip
1Move the Joystick up/down ( ) to zoom in/out the
image until a proper scene is set.
2Press the Shutter button ( ) to take a photo.
Taking a photo
Press this button to shift between 2D/3D mode. Pressing this
EXWWRQLQSUHYLHZZLOOGHWHUPLQHZKHWKHUWKHUHFRUGHG¿OHLV
2D or 3D. Pressing this button in playback will let you see the
'RU'¿OHVVWRUHGLQ\RXUFDPFRUGHURUPHPRU\FDUG1RWH
WKDW'¿OHVFDQQRWEHUHFRUGHGYLHZHGGHOHWHGLQ'PRGH
and vice versa.
1
2
3
2
1
Blurred photos may occur due to hand shake. To avoid blurred photos, please hold the
camcorder steady when taking photos or use a tripod to eliminate shaking.
When recording in a dim environment, please use extra light source to illuminate the
subject.
When recording or shooting in 2D mode, only the right lens is used for capturing image.
This product utilizes the “Parallax Barrier” 3D technology. The parallax barrier is a
special layer placed in front of the LCD screen. In 3D mode, it allows each of your eye
to see a different set of pixels on the screen (hence the 3D effect), and as a result the
brightness of the screen will also seem to be halved in 3D mode.
5
1Press the OK button ( ) to enter Playback preview mode.
Press the 2D/3D button ( WRVZLWFKEHWZHHQ'RU'¿OHV
2Use the Joystick ( ) to navigate through your
UHFRUGLQJVDQGVHOHFWD¿OH3UHVV2. ) to view the
¿OHLQIXOOVFUHHQ:KHQD¿OHLVYLHZHGLQIXOOVFUHHQ
and is not playing or being zoomed and locked, you can
move the Joystick left/right ( ) to shift between the
SUHYLRXVRUQH[W¿OH
3-1
When playing a video, you can move the Joystick
left/right ( ) to fast rewind or fast forward, or press
the OK button ( ) to pause or resume the playback. You can also move the
Joystick up/down ( ) to bring up volume control and then left/right ( ) to
adjust volume.
3-2
When viewing a photo, you can move the Joystick up/down ( ) to zoom in/out.
Press the OK button ( ) to lock ratio and use the Joystick ( ) to browse the
photo. To exit the zoomed condition, press OK ( ) and use the Joystick ( ) to
zoom out the image until back to normal ratio, or simply press the Shutter ( )
button.
4To exit Playback mode, press the Shutter ( ) button.
Playback
0001/0010 Battery life
File type 1:
'¿OH
'¿OH
File type 2:
: video
: picture
Press Shutter to return
to previous screen
Press OK to
display in full
screen
&XUUHQW¿OH7RWDO¿OHV
Highlight frame Storage:
: internal
: memory card
Full screen playback
0001/0010
00:00:10
6
Menu operations
1Push the Joystick to the right ( ) to bring up menu.
2Move the Joystick up/down ( ) to select a menu item
and Press OK ( ) to enter.
3Move the Joystick up/down ( ) to select your desired
option and press OK ( WRFRQ¿UP
4To exit menu, push the Joystick to the left ( ).
5-way
Joystick
1Press the OK button ( ) to enter Playback mode and
use the Joystick ( WRVHOHFWD¿OH
2Press the Delete button ( ) and 3 options will be
available:
Option Description
Yes 'HOHWHWKHVHOHFWHG¿OH
No ([LWPHQXZLWKRXWGHOHWLQJWKH¿OH
All 'HOHWHDOOYLGHRDQGLPDJH¿OHVLQWKHVDPH
folder (3D or 2D)
2
1
'HOHWLQJ¿OHV
Menu items
Menu items Description
Language Select the language for the Camcorder.
Date & Time To setup the date and time, move the Joystick up/down ( ) to adjust
value; left/right ( WRVKLIWEHWZHHQ¿HOGV3UHVV2. ) to save
the changes.
Date Stamp Print a date and time mark on each photo (photo only).
Icon Enable or disable the icons shown on the display.
Flicker 6HWÀLFNHUIUHTXHQF\WR+]RU+]6HHWKH³)OLFNHUWDEOH´IRUPRUH
details.
Inhaltsverzeichnis
Andere AIPTEK Camcorder Handbücher
AIPTEK
AIPTEK AHD-AF1 Bedienungsanleitung
AIPTEK
AIPTEK PenCam Trio HD 8GB Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV5900 Bedienungsanleitung
AIPTEK
AIPTEK Pocket DVT300LE Bedienungsanleitung
AIPTEK
AIPTEK T8 Bedienungsanleitung
AIPTEK
AIPTEK HD-1 Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV2 Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV6800 Bedienungsanleitung
AIPTEK
AIPTEK PENCAM_HD Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV4500 Bedienungsanleitung
AIPTEK
AIPTEK SportyCam Z3 Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV5100 Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV5800 Bedienungsanleitung
AIPTEK
AIPTEK AHD-H23 Bedienungsanleitung
AIPTEK
AIPTEK MPVR Bedienungsanleitung
AIPTEK
AIPTEK PENCAM TRIO HD Bedienungsanleitung
AIPTEK
AIPTEK AHD Z700 Extreme Bedienungsanleitung
AIPTEK
AIPTEK Pocket DV 5100M Bedienungsanleitung
AIPTEK
AIPTEK Pocket Pocket DV Leitfaden
AIPTEK
AIPTEK AHD-H12 EXTREME Bedienungsanleitung
Beliebte Camcorder Handbücher anderer Marken
Panasonic
Panasonic AG-HMC152EN Bedienungsanleitung
Insignia
Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung
MYDLINK
MYDLINK DCS-6100LH Bedienungsanleitung
Sony
Sony video Hi8 Handycam CCD-TR555 Bedienungsanleitung
SECURECOM
SECURECOM V-5014B Bedienungsanleitung
Panasonic
Panasonic HDC-SD100 Bedienungsanleitung
