Airwell DSD 40 RCA Series Bedienungsanleitung

CENTRAL AIR CONDITIONER

SPLIT SYSTEM

WITH ELECTRONIC CONTROL

SERIES:

INSTALLATION INSTRUCTIONS

DSD40RCA / GCD 40 RC

DSD40RCA/ GCD 40 RCX

DSD50 RCA / GCD 50 RCX

DSD60RCA/ GCD60 RCX

DSD / CAT. NO / ENG/,6+5(9

INDEX

GENERAL............................................................................................................................................. 2

UNIT LOCATION CRITERIA................................................................................................................. 2

DIMENSIONAL DRAWINGS................................................................................................................. 3

INDOOR UNIT INSTALLATION.......................................................................................................... 6

Indoor unit location........................................................................................................................... 6

Floor mounting.................................................................................................................................. 8

Ceiling mounting............................................................................................................................... 8

OUTDOOR UNIT INSTALLTION........................................................................................................... 9

INSTALLATION OF INTERCONNECTING TUBING BETWEEN INDOOR AND OUTDOOR UNIT.... 10

General............................................................................................................................................. 10

Recomendation for interconnecting tubing installation..................................................................... 11

Setting in operation.......................................................................................................................... 12

DRAIN INSTALLTION........................................................................................................................... 14

ELECTRICAL CONNECTIONS............................................................................................................. 14

Interconnecting cable........................................................................................................................ 17

Display control unit............................................................................................................................ 16

RCW-Remote control........................................................................................................................ 18

FINAL TASKS........................................................................................................................................ 20

1. GENERAL

The DSD air-conditioners include two separate units - Indoor and Outdoor Unit. The two units are

interconnected by two refrigerant tubes and an electric cable. The DSD indoor units can be supplied with

right or left hand access for service and tube connection. Right/left hand sides are defined when looking at

the unit from behind it (filter side). Unit functions are controlled by a Display Control Unit and a wireless

Remote Control (or optional wired Remote Control). For outline dimensions - see Figure 1.

WARNING

The air conditioner must be installed by authorized technicians, according to company specifications and

using company standard tubing, electric cables and proper installation tools. Failure to comply with the above

may invalidate your warranty!

2. UNIT LOCATION CRITERIA

In selecting proper location, the following criteria must be considered:

a) The outdoor unit and the indoor unit must be installed as close to each other as possible. For

tubing length and diameters - see Table No.1. If longer tubing is required consult your dealer.

b) Outdoor unit installation should provide for:

•Easy service access.

•Minimum disturbance to the owner and nearby neighbors.

•A minimum distance of 200 mm from the wall, as shown in Figure 8.

•If installed in a closed place (balcony, attic, etc.), outdoor air vent must be provided to prevent hot/cold

air from recirculating through the outdoor unit.

•If several outdoor units are installed in the same area, make sure that the hot air outlet from one

outdoor unit does not enter another outdoor unit.

•Verify that any wall on which the outdoor unit is installed is capable of carrying the unit’s weight. Do not

install on a light unstable structure susceptible to vibration.

•When installing on a balcony above the first floor, make sure that the outdoor unit location allows easy

access for removal of the top cover and/or the entire unit, if necessary

•If the outdoor unit is installed in a non-accessible location, long and flexible refrigerant tubing and

electrical cable must be installed to allow the unit to be moved for servicing.

•Do not install the unit in a highly polluted area in which the air is contaminated by oil mist, salt or

sulfuric gas.

3. DIMENSIONAL DRAWINGS

INDOOR UNIT (Evaporator) - right side connection

1. Air Supply

2. Electrical Box

3. Access Panel

4. Refrigeration Tubing

Port

5. Drain Port - G (OD)

6. Return air spigots

7. Control Unit Port

8. Main Power Port

Figure 1. Indoor Unit Outline Dimensions & Return Air Spigot Connection Size

DSD 40 RCA / GCD 40 RC

DSD 40 RCA / GCD 40 RCX

DSD 50 RCA / GCD 50 RCX

DSD 60 RCA / GCD 60 RCX

Dimensions DSD 40 RC

DSD 50 RC

DSD 60 RC

785 1040 1140

B755 1010 1115

C710 965 1085

D300 360 335

E595 595 680

F25 25 340

G3/4" 3/4" 3/4"

H325 325 378

W608 865 1021

490 490 340

OUTDOOR UNIT (Condenser)

GCD 40 RC, GCD 40 RCX, GCD 50 RCX

1. Wiring connections

2. Suction tube connector (flared)

3. Liquid tube connector (flared)

4. Service valves

5. Service taps

6. Air inlet

7. Air outlet

Figure 2. General dimensions of GCD 40 RC, GCD 40 RCX, GCD 50 RCX outdoor units

WALL

300

MIN

300 MIN

WALL

600

MIN

WALL

1000 MIN

WALL

500 MIN FROM TOP

MINIMUM CLEARANCE mm

Figure 3. General dimensions of GCD 60 RCX outdoor unit

Figure 3A. - Example of Installation

OUTDOOR UNIT (Condenser)

GCD 60 RCX

WALL

300

MIN

300 MIN

WALL

600

MIN

WALL

1000 MIN

WALL

500 MIN FROM TOP

MINIMUM CLEARANCE mm

4. INDOOR INSTALLATION

4.1 Indoor Unit Location (See Figure 4)

The indoor unit is designed for installation on a false ceiling or other compartment, where

there is no influence from outdoor conditions.

While selecting the location, the following conditions must be assured:

a) The location should assure free flow of the return air into the unit without

interference.

b) The unit should not be installed close to rooms where noise should be avoided

(bedrooms, children rooms, etc.).

The location should allow good air circulation.

1. Frame installed by

Technical Personnel

2. Flexible Joint

3. 1” thick Duct Acoustic

Insulation

4. Cross Section Area

min. 800x300 mm

5. Return Air Intake Grille

800x900 mm (or

similar)

6. Return Air Intake

7. Air Filter Opening and

Cover

8. Bottom Access

9. Electrical Box

10. Acoustic Insulation

470

Figure 4. Requirements for Indoor Unit Location

FRESH AIR INTAKE

If required this must be fitted to the return air ducting as no special provision is made within the unit.

All fresh air intakes must be provided with air filters if they are connected to the ductwork between

the return air filter and the unit.

Consideration should be made to the return air sensor. The ducted units have a return air sensor

mounted near the return air coil. Fresh air influences may affect the room temperature. Relocating

the position of the return air sensor may be required.

AIR FILTERS

Air filters are not provided and no provision is made for fitting them within the unit as standard.

Air filters should however be provided by the installing contractor and located in an accessible location

between the return air grille and the unit. These filters must be sized for a maximum face velocity of

2.0 m/sec.

Where the unit must be installed in an attic space or outside, the following conditions must be

assured:

a) The unit must be protected from rain, heat and radiation by an additional layer of 1”

thick thermal insulation.

b) The return-air duct should be as short as possible, with a minimum dimension of

700x300 mm (or similar cross section) with full acoustical lining inside, and no more

than two long-radius elbows. The cross section at the duct connection to the unit shall

be equal to that of the unit.

c) The distance between the return air grille and the air intake on the unit must be as

short as possible. A minimum free passage of 0.3 m is necessary along the entire

return-air path.

d) The installation should be designed to withstand the weight of the unit and avoid

resonance vibrations. Use serrated rubber mounting under the unit and flexible joints

for the air duct.

Design and prepare in advance easy access for servicing as follows: (See Figure 4)

e) The minimum height clearance for the installation is 470 mm.

f) Allow the access to the electrical control box to facilitate its easy removal by opening

the cover (fastened by 3 screws). Allow also the access to the 700 mm long cable

which is tied inside the unit to enable relocation of the control box.

g) A distance of 200 mm must be kept between the rear side of the unit and any near-by

wall, to allow free air passage.

h) A distance of 300 mm must be kept to allow free air intake and convenient access to

air filters. Allow the access to service panels from opposite sides (right and left) for

the maintenance of fan and motor.

4.2 Floor Mounting - for DSD Series Only

(See Figure 5)

Place two layers of serrated 60x60 mm rubber pa at the four

corners under the unit base. Insert a 1.5 mm thick sheet metal

between the two rubber pads and between the bottom pad and

the concrete surface.

1. Serrated Rubber 60x60 mm

2. Sheet Metal 60x60 mm

3. Concrete Surface

Figure 5. Indoor Unit Installation

4.3 Ceiling Mounting

The indoor unit can be mounted using spring or serrated rubber

isolators.

a. Spring isolators mounting

Insert four 3/8” stu in the ceiling according to the

dimensions of the spring-type isolators. Mount four spring

type isolators as shown in Figure 6. Attach indoor unit to

the spring-type isolators and level it, using the leveling

nuts. Secure in place by tightening the fastening nuts.

1. Concrete Ceiling

2. Bolt for Ceiling Insert

3. Leveling Nut

4. Fastening Nut

Figure 6. Indoor Unit Installation –

Ceiling Mounting using Spring Isolators

b. Serrated Rubber Mounting

In sites where the spring isolators assemblies

cannot be installed, mount the unit as show in

Figure 7. Insert four 3/8” studs in the ceiling

according to the dimensions of the suspension

angle frame mounted on the unit. Prepare two

30x30 mm, 1.5 mm thick galvanized sheet metal for

each stud and assemble according to Figure 6. The

rubber pa may be substituted by springs suitable for

this type of installation.

1. Concrete Ceiling

2. Bolt for Ceiling Insert

3. Leveling Nut

4. Fastening Nut

Figure 7. Indoor Unit Installation -

Ceiling Mounting using Rubber

Isolators

5. OUTDOOR UNIT INSTALLATION

Installation on flat surface (roof, ground, etc.)

Install outdoor unit support in a position elevated at least

100 mm on a concrete pad, concrete block or wooden beams,

in order to allow free water flow underneath (See Figure 8).

1. Outside the building

2. Outdoor Unit

3. Serrated Rubber 40x80 mm

4. Floor

5. Concrete base or floor tiles

6. Anchor Screws

7. Wall

Figure 8. Outdoor Unit Installation Criteria

1000 mm

MIN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Airwell Klimaanlage Handbücher

Airwell

Airwell AWSI-HKD009-N11 Bedienungsanleitung

Airwell

Airwell AWSI-FWD012-N11 Bedienungsanleitung

Airwell

Airwell AW-HDL007-N91 Bedienungsanleitung

Airwell

Airwell AWSI-HKD009-N11 Bedienungsanleitung

Airwell

Airwell HAF 18 Bedienungsanleitung

Airwell

Airwell Trio Dakota 5.2 DCI Bedienungsanleitung

Airwell

Airwell AW-FWDB018-N91 Bedienungsanleitung

Airwell

Airwell AW-HDL012-N91 Bedienungsanleitung

Airwell

Airwell AWSI-HND007-N11 Bedienungsanleitung

Airwell

Airwell HAF 7 Bedienungsanleitung

Airwell

Airwell XLM30RCB Bedienungsanleitung

Airwell

Airwell FLO 9 DCI Bedienungsanleitung

Airwell

Airwell Comfort Series Bedienungsanleitung

Airwell

Airwell AW-YHDM009-H91 Bedienungsanleitung

Airwell

Airwell FSF Series Bedienungsanleitung

Airwell

Airwell DS 28 RCFA Bedienungsanleitung

Airwell

Airwell ST-NFMFL 16R Bedienungsanleitung

Airwell

Airwell WAP Series Bedienungsanleitung

Airwell

Airwell GC 43 Bedienungsanleitung

Airwell

Airwell PNX 012 Bedienungsanleitung

Airwell

Airwell WFD 009 Bedienungsanleitung

Airwell

Airwell AWAU-YUDA060-H13 Bedienungsanleitung

Airwell

Airwell CVQA-015N-01M22 Leitfaden

Airwell

Airwell MAY 110 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung