Airwolf 3D AW3D HDL Bedienungsanleitung
2 | P a g e
AW3D HDL
User Manual
www.Airwolf3D.com
Table of Contents
Specifications .............................................................................................................................................. 4
Unboxing the Printer................................................................................................................................... 5
Box Contents ........................................................................................................................................... 5
Part Directory.............................................................................................................................................. 6
How it Works............................................................................................................................................... 7
Extruder Assembly .................................................................................................................................. 7
Hot End and Heat Bed Motion ................................................................................................................ 7
Plug In & Turn On........................................................................................................................................ 8
Pre-Printing Steps ....................................................................................................................................... 9
Quick Start Guide .................................................................................................................................... 9
Quick Start Guide (contd.)..................................................................................................................... 10
1) Leveling the Bed................................................................................................................................ 11
First Print & Calibration......................................................................................................................... 12
First Print & Calibration (contd.) ........................................................................................................... 13
2) Loading Filament............................................................................................................................... 14
3) Bed Preparation ................................................................................................................................ 15
4) The First Layer ................................................................................................................................... 15
RAMBo Driver ........................................................................................................................................... 16
Setup (Windows 8 Only)........................................................................................................................ 16
Installation (PC Only)............................................................................................................................. 17
5 Steps to Printing..................................................................................................................................... 20
1) Download or Design a 3D Model ...................................................................................................... 21
2) Convert to STL File Type.................................................................................................................... 22
3) Netfabb: Layout (STL Clean Up) ........................................................................................................ 22
3) Netfabb: How To (STL Clean Up)....................................................................................................... 23
4) Slicing ................................................................................................................................................ 24
Slicing: Breakdown ................................................................................................................................ 25
4-5) MatterControl PRO: How To.......................................................................................................... 26
3 | P a g e
4-5) MatterControl PRO: How To (contd.) ............................................................................................ 27
Two Part Epoxy...................................................................................................................................... 28
Firmware...................................................................................................... Error! Bookmark not defined.
Maintenance............................................................................................................................................. 29
Belt Tensioning...................................................................................................................................... 30
Rod Alignment (X-axis).......................................................................................................................... 31
Rod Alignment (Y-axis) .......................................................................................................................... 32
Rod Lubrication ..................................................................................................................................... 33
Inserting Filament ................................................................................................................................. 33
Wiring Diagram ..................................................................................................................................... 34
Clogged Nozzle ...................................................................................................................................... 35
Changing the Nozzle.............................................................................................................................. 36
Trouble Shooting....................................................................................................................................... 37
Glossary of Terms ..................................................................................................................................... 38
Hardware............................................................................................................................................... 38
Software ................................................................................................................................................ 38
Contact List ............................................................................................................................................... 38
Notes......................................................................................................................................................... 39
Notes......................................................................................................................................................... 40
4 | P a g e
Specifications
Copyright 2013 ©
Designed and
Manufactured In:
12 x 8 x 11 inch
300 x 200 x 280 mm
24 x 17.5 x 18 inch
610 x 445 x 460 mm
38 lbs
17 kg
Material that can
be printed:
Filament
Diameter
Nominal: 3.00mm
Actual: 2.85 ± 0.1mm
mm
Nozzle Diameter 0.5 and 0.35 mm
0.1 mm
0.0039 inch
100 mm/s
3.94 inch/s
200 mm/s
7.87 inch/s
Circuit Board
Frame
Power Supply
File Format
System
Compatibility
General
Partially Enclosed Acrylic
Har
d
Printer Size
(LxWxH)
Internal auto-switching 13.5V DC, 300W
Weight
USA
PLA, Soft PLA, PLA 4043D, BendLay,
LayWOO D-3, Laybrick, HIPS, T-Glase,
PVA, TPE & more to come!
Build Volume
(LxWxH)
Minimal Layer
Thickness
Max Speed-
Perimeter
Max Speed-
Travel
Specs.
Matter Control
Cura & Slic3r
RAMBo
Comp.
Software
Netfabb & MeshLab
Windows, Mac, Linux
STL & GCODE
5 | P a g e
Unboxing the Printer
Box Contents
6 | P a g e
Part Directory
7 | P a g e
How it Works
Extruder Assembly
Hot End and Bed Motion
8 | P a g e
Plug In & Turn On
9 | P a g e
Pre-Printing Steps
Quick Start Guide
10 | P a g e
Quick Start Guide (contd.)
Inhaltsverzeichnis
Andere Airwolf 3D 3D-Drucker Handbücher
Airwolf 3D
Airwolf 3D AW3D HD Bedienungsanleitung
Airwolf 3D
Airwolf 3D HDR Bedienungsanleitung
Airwolf 3D
Airwolf 3D AW3D v.4 Bedienungsanleitung
Airwolf 3D
Airwolf 3D HD2x Bedienungsanleitung
Airwolf 3D
Airwolf 3D HDR Bedienungsanleitung
Airwolf 3D
Airwolf 3D EVO Additive Manufacturing Center Bedienungsanleitung
