Akasa Evo blue AK-922 Bedienungsanleitung

Installation Instruction

Improper Installation will result in damage to the processor. Never

switch on the computer system until the fan is connected.

WARNING

heatsink speciﬁcation

dimension : 138 x 112 x 75 mm

weight : 754 g

material : aluminium with copper base(bonded) and heatpipes

ENGLISH

(AK-921)HEATSINK ONLY

(AK-922)

fan speciﬁcation (AK-922 only)

dimension: 92 x 92 x 25mm

weight: 98g

speed: 600 – 3000 RPM

airﬂow: 67.9 CFM max

air pressure: 5.5mm H2O

bearing type: dual ball bearing

voltage rating: 12V

connector: 4-pin (PWM) with 3-pin functionality

noise level: 18 db(A) – 36 dB(A)

AKASA Company notices

The information contained in this document is subject to change without notice.

prohibited without prior written permission of AKASA, except as allowed under

The only warranties for AKASA products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein

should be construed as constituting an additional warranty. AKASA shall not be

liable for technical or editorial errors or omissions contained herein.

Installation Manual

Installation Components

(A) X 1pcs (B) X 4pcs (C) X 4pcs

(D) X 4pcs

LGA775

AMD K8

(E) X 1pcs (F) X 1pcs

(G) X 1pcs

AK-921 (additional parts)

(H) X 8pcs (I) X 4pcs

(J) X 1 pcs

(J) X 1pcs

(K) X 1pcs

1. Place a rubber washer (part D) over each of the screws of the LGA775

backplate (part A).

2. Place the LGA775 backplate under the motherboard aligning the screws to ﬁt

through the four holes available around the CPU as illustrated.

for LGA775

AK-922

3. Place the thick rubber pads (part C) over each of the four (4) screws so they

sit on the motherboard as shown.

4. Apply the proper amount of thermal compound on the CPU surface; a thin

layer is ideal, extra thermal compound will not improve performance. Make sure

the CPU surface is perfectly clean. If not, clean it with Isopropyl or Akasa

Timclean.

5. Position the cooler over the four mounting screws. The installation direction

of the heatsink will depend on your case and its airﬂow requirements.

6. Secure the cooler with the collar nuts (part B), one for each screw, tighten

the nuts gradually in a crosswise manner.

8. Connect the 4-pin fan connector to the CPU fan motherboard connector. If a

connector marked CPU fan is not apparent on the board, check the

motherboard manual for fan connection information.

1. Remove the retention bracket from the motherboard by removing the screws

(or pins in some motherboards).

Note: It may be possible that the removal of the original backplate is not required if the cooler spring loaded

screws are compatible.

for AMD K8

7. Connect the 2-pin female LED connector to the 2-pin male power connector

from the fan.

3. Take off the pre-attached LGA 775 heatsink retention bracket and retain the

four (4) screws for the next step.

4. Place the K8 heatsink retention bracket (part F) on the heatsink base

aligning the ﬁxing screws with the Fan bracket indents and the corresponding

screw holes.

2. Place the backplate provided (Part E) below the motherboard aligning the two

standoffs with the holes in the motherboard as illustrated.

6. Place the cooler on top of the CPU; align two spring loaded screws with the

backplate standoffs and secure the cooler by tightening the screws.

5. Secure the heatsink retention bracket with four (4) screws from step three.

Apply the proper amount of thermal compound on the CPU surface; a thin layer

is ideal, extra thermal compound will not improve performance. Make sure the

CPU surface is perfectly clean. If not, clean it with Isopropyl or Akasa Timclean.

7. Connect the 2-pin female LED connector to the 2-pin male power connector

from the fan.

8. Connecting the fan:

A. Remove a PCI slot backplate and install the fan control unit (part K).

B. Connect the 4-pin fan connector to the male connector of the Y cable.

C. Connect the 3-pin female connector (with red / yellow / black wires) to the fan control.

D. Connect the 3-pin female connector (with yellow / black wires) to the CPU fan

motherboard connector.

E. Connect the fan control to the 4-pin PSU connector.

For AK-921 installation follow the AK-922 manual steps 1-6 for LGA775 and

AMD K8. After that; connect the LED 2-pin connector with 4-pin PSU connector

using part G.

AK-921 (LGA 775 and K8)

You can use provided screws (parts H and I) to attach your favorite fan.

A B C

D E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Akasa Computerhardware Handbücher

Akasa

Akasa Venom A10 Bedienungsanleitung

Akasa

Akasa SOHO H4 Bedienungsanleitung

Akasa

Akasa A-NUC40-M1B Bedienungsanleitung

Akasa

Akasa Venom A10 Bedienungsanleitung

Akasa

Akasa InterConnect AC-ICR-08 Bedienungsanleitung

Akasa

Akasa EVO 120 Bedienungsanleitung

Akasa

Akasa AK-961 Bedienungsanleitung

Akasa

Akasa Venom Voodoo Bedienungsanleitung

Akasa

Akasa A-NUC70-A1B Bedienungsanleitung

Akasa

Akasa FREEDOM POWER AK-PSS075FGM Bedienungsanleitung

Akasa

Akasa 975058 Bedienungsanleitung

Akasa

Akasa SOHO H4 PLUS Bedienungsanleitung

Akasa

Akasa ALUCIA H4 PLUS Bedienungsanleitung

Akasa

Akasa LGA775 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung