AKCP SecurityProbe 5ES-X20 Bedienungsanleitung

www.AKCP.com

SecurityProbe

5ES-X20/X60

User Manual

Help Version updated till firmware 403H

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 2 -

1) Introduction

1. What is securityProbe 5E Standard?

2. How to use this manual

3. Package Contents

4. Front and Rear Panels

2) Installation

1. Setting the IP address

2. Testing the IP address

3. Firmware upgrade

4. Multi User Groups and Management

5. Services and Security

6. Setting up a sensor

i) Notification thresholds

ii) Advanced sensor settings

7. Expansion Ports

3) Notifications

1. Adding a notification

2. SNMP trap

3. E Mail

4. SMS notification

4) Mapping

1. Adding a map

2. Monitoring via map interface

5) Filters

1. Sensor filters

2. Syslog filters

6) Making my unit visible to the internet

7) FAQ

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 3 -

1) Introduction

What is securityProbe 5E “Standard”?

The securityProbe-5ES Standard integrates over 10 years of environmental monitoring

experience with the latest technology to push the boundaries of disaster protection. Now

you can sense and see problems before they lead to business disruptions. It is a high

speed, accurate, intelligent monitoring device, featuring a completely embedded host and

Linux Operating System. The design is based on our successful securityProbe 5E, but

without the camera inputs. This gives you everything you need and nothing you don't!

AKCP has prided itself on bringing a low cost, easy to use monitoring solution to market with

the securityProbe-5ES.

What’s the difference between the securityProbe 5ES and

the securityProbe 5ES-X20?

The securityProbe 5E-X20 has the 8 RJ-45 intelligent sensor ports AND has 20 extra dry

contact inputs, where the securityProbe 5E only has the 8 RJ-45 sensor ports. More on

these extra dry contacts in the sections below.

How to use this manual

This manual is meant to provide the user with a step by step guide on how to configure

and set up their unit. It utilizes screen shots in an effort to make things simpler for the

user to follow. It is split up into sections that form “mini tutorials”. These cover the basic

set up and common configurations of the unit, and give an introduction to its most useful

features.

At the end of the manual there is a FAQ section that provides some further in-depth

information regarding specific set ups and answers some commonly asked questions. If

you need any further information or help with using your unit then please contact us on

support@akcp.com and one of our technical support staff will be only to pleased to help

you with any information you require.

Package Contents

Your Securityprobe-5ES package contains the following items:-

1x Product CD

1x 5ft Crossover cable

1x THS00 with 5 ft straight cable

1x 7.0 –9 V, 2.5 A power supply

2x Brackets for rack mounting

1x Blue quick-start guide.

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 4 -

Front and rear panels

securityProbe 5ES

Fig 1. Front panel

The front panel has several LEDs which display the units status and notify you as to its

activity.

1. Power LED

When the unit is powered up the power LED will be lit continuously. If the power LED

is flashing then it indicates a problem with the CPU. If you notice this then please

2. Ethernet LED

The Activity and Link LEDs indicate network connectivity and activity. The Link LED

will light up when there is a network connection present. The activity LED will flash

when there is network traffic being sent or received by the unit.

3. Status / Online LEDs

These are numbered 1 –8. They are used to indicate the connectivity status of the

sensors connected to each port. These LEDs also can be used to indicate system

status when undertaking various operations.

1. The LEDs will indicate the progress of an upgrade. The red LEDs will move

from left to right to indicate activity, and the green LEDs will indicate overall

progress of the upgrade. When all the red lights are off and all green are on

the upgrade / recovery process is complete.

2. These lights will indicate if the unit is operating in safe mode. This is when

the unit loads the Operating System (OS) with a minimal set of drivers. If

your device enters safe mode after rebooting then please contact us on

support@akcp.com

3. The unit may enter recovery mode if a firmware upgrade has been

incomplete. This will be indicated by the unit displaying a continuously lit row

of red LEDs. If this happens please contact us on support@akcp.com

4. Mic

The mic is a small hole for access to the internal microphone. This can be used as a

sound sensor (or an external mic can be used)

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 5 -

5. Expansion Ports

There are four expansion ports numbered from E1 –E4. These are expansion Ports

for connecting either the 8port expansion or 16 dry contact expansion modules.

6. Removable SD slot

This slot so where you can place your SD card which can store data such as pictures

taken from the CCTV camera, sounds recorded from the internal microphone, and

also the current firmware of the unit.

Fig 2. Rear panel.

The rear panel of the unit is home to various ports and connections. The functions of

these are as follows :-

1. Reset button

The black tact switch button is used to perform the following functions

1. A single press will announce the IP address of the unit. This is audible

through the internal speaker. It also broadcasts the IP address to the IPset

program.

2. Turns off password checking when accessing the web based interface (hold

down for 7 seconds)

3. To reboot the unit into the firmware upgrade mode (hold down for 12

seconds)

2. Sensor ports

There are 8 RJ45 ports numbered from 1 –8. These are for connecting AKCP

intelligent sensors to the unit.

3. USB port

The unit is equipped with one USB 1.1 port. This can be used, for example, to

connect a USB GPRS/GSM compatible modem, a USB WiFi dongle or USB

Bluetooth dongle.

4. Mic Out

This is used to connect an external microphone for voice modem applications.

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 6 -

5. Audio in / out

The in is used to connect an external microphone, the output for external speakers.

6. RS485 Port

Used for Modbus connectivity. We support Modbus master or slave.

7. Power Connector

This is a 7.5V DC plug. We recommend you using a 7.0 –9 V, 2.5 A power supply.

8. Ethernet Port

This RJ45 port is used to connect your unit to the network.

9. External ground

The EXT. GND can be used to external ground the unit.

securityProbe 5ES-X20

securityProbe 5ES-X20 20 Extra Dry Contact Inputs

The 20 extra dry contact inputs on for example, the securityProbe 5ES-X20, (or

securityProbe 5ES-X60) can be configured as inputs only up to 5 Volts in normal

operation. In opto-isolation mode they can input up to 30 Volts DC. This will protect these

inputs and the unit from high voltages and spikes.

Opto-isolators provide complete electrical separation between the securityProbe 5ES-

X20 and the dry contact. The base units are therefore protected against possible large

voltage spikes caused by lightning for example.

The figure below shows the JUMPERS (on the dry contact board) set up to provide opto-

isolators support. Opto-isolators provide complete electrical separation between the

securityProbe 5ES-X20 and the dry contact.

Please refer to the rear panel of the securityProbe 5ES above for the other connections

on the rear panel as they are exactly the same in functionality.

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 7 -

The OID for the extra dry contact inputs is:- .1.3.6.1.4.1.3854.1.2.2.1.18.1.3.<port>

Extra dry contact input practical applications:

The extra dry contact inputs can be used to monitor many types of equipment, for example, you

can run the connection from warning lights on alarm panels to the dry contact inputs, so that

when the warning light on the alarm panel is activated, the dry contact is triggered in the units

web interface, thus allowing you to send notifications via emails or SNMP traps.

securityProbe 5ES-X20 extra dry contact web interface setup

First login to the securityProbe 5ES-X20 web interface, then navigate to the Sensors Page, then

click on the Dry Contact Ports link in the left hand column. You can now click on the dry contact

port to setup that port as shown in the screen shot above.

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 8 -

In the Normal tab settings we can see that the sensor is currently Offline, so to enable the dry

contact port we would click on the Offline button.

Now we can see the dry contact input is now Critical and we can set how we require the Normal

State to be in as shown above. Either in the Closed GND or Open +5VDC. We can also rename

our normal and critical state of the input.

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 9 -

Now we can see that the dry contact input now is in the normal state as shown in the screen shot

above.

If we click on the Advanced Tab, we can set the graphing to on, the sensor URL, set the Filter

Status and enable the Calendar. (More on the Sensor URL and Filter Status in sections #)

securityProbe 5ES securityProbe 5ES-X20 Manual

Updated until firmware 403H - 10 -

2) Installation

1. Setting up the IP address

Every unit is shipped with the default IP address of 192.168.0.100 First we will go through

the process of changing this IP address to fit your own network configuration.

Ensure the following items are available to you before starting:-

1. RJ45 CAT5 crossover cable with RJ45 male connection

2. A PC with Ethernet card or LAN socket.

3. Power socket for the unit to connect to

a) Connect the unit via the Ethernet port of the unit to your computers LAN or Ethernet

port with a CAT5 crossover cable.

b) Open a web browser and type the default IP address, hit enter.

In some cases your computer might not be able to connect to this default IP address. In

this situation you need to set up your computers routing table to allow access to this. See

the appendix on how to setup this.

c) You will now be presented with the following screen. The default password for Admin

is “public”. To make your unit secure and change the password.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AKCP Sicherheitssystem Handbücher

AKCP

AKCP 5ESV-X20 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung