Akerstroms JUPITER 8B Bedienungsanleitung
948682-000 EN/SV B0
OPERATING MANUAL/
ANVÄNDARMANUAL
JUPITER 800/900
8B, 9B RS, 10B,
9BD RS & 10BD
FSK12
Revision History
Version Date Reason
A0 2013-07-04 1st released version
A1 2013-11-20 Changes in B10
B0 2014-03-25 Tandem and multi-operator operation added
MANUAL LANGUAGES 3 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
SV
MANUAL LANGUAGES
Operating Manual JUPITER 8B, 9BRS & 10B 4
Tandem and multi-operator operation 14
Användarmanual JUPITER 8B, 9BRS & 10B 16
Tandem- och erförardrift 26
Figures JUPITER 8B/9BRS/10B NORDIC symbols 28
Figures JUPITER 8B/10B DIN symbols 29
Figures JUPITER 8B/9BRS/10B CS symbols 30
Symbol explanation / Symbolförklaring 31
Operating Manual JUPITER 8B, 9BRS & 10B 4 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
OPERATING MANUAL JUPITER 8B, 9BRS & 10B
!The equipment has to be controlled by a qualied operator
MAINTENANCE
To maintain availability and operational safety, a regular maintenance is
necessary on the system.
Daily maintenance
Before each use of the transmitter, check the following items for faults or
damages:
• Visual inspection of the transmitter enclosure (cracks, dents)
• Visual inspection of rubber cover for buttons (cracks)
• Broken/faulty buttons
• Visual inspection of carrying device
• Visual inspection of battery (cracks, dents)
• Test that the battery lock is functioning normally
• Test of safety stop button (it shall be intact and easy to move)
If there is any damage or fault contact an authorized service technician.
Weekly maintenance
• Clean the battery contacts and the contacts on the transmitter and
charger
• Clean the transmitters control panel and check that the print is still
readable
!For cleaning use a dry cleaning cloth, if necessary use a wet cleaning
cloth and a soap solution. Never use a alcohol-based product for cleaning,
it can seriously damaged the plastic.
Operating Manual JUPITER 8B, 9BRS & 10B 5 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
START THE TRANSMITTER AND ACTIVATE THE MAIN CONTACTOR
The following procedure has to be followed when starting the transmitter:
1. Make sure no buttons are pressed.
2. Release the STOP button.
3. The status indicator should show slow blinking green.
4. Activate the main contactor in the receiver by pushing down the
button B9 (1st step).
The unit is now in operating mode.
PIN LOCKED
If the transmitter is PIN locked at startup the two top buttons LED would lit
and status indicator shows red continuous light. Display will show “Enter
PIN”. Enter the 4-digit PIN with the buttons:
8B: B3-B8 where B3=1, B4=2, B5=3, B6=4, B7=5 and B8=6
9 BRS & 10B:
B1-B8 where B1=1, B2=2, B3=3, B4=4, B5=5, B6=6, B7=7 and B8=8
At successful login the two top buttons LED goes out and the status indicator
shows green ashing. Display shows “PIN OK!”. The unit is now in operating
mode. See installation manual for conguration of the PIN lock.
NORMAL OPERATION
The transmitter is designed with two push buttons for HOIST Up/Down,
TROLLEY Left/Right and BRIDGE Forward/Reverse. Each button is divided
into 2 steps (a perceptible resistance) which facilitates the running at a certain
speed. The rst speed is obtained when the push button is half compressed
and the second speed is obtained when the push button is totally compressed.
All the motions can be run simultaneously and the motions will be stopped
when the push button is released, if not make an forced STOP using the safety
STOP button.
Operating Manual JUPITER 8B, 9BRS & 10B 6 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
SIGNAL
A signal can be emitted at any time during the run and sounds as long as the
push button
is depressed (1st step).
Risk of high noise sound, hearing protection required.
EXTRA FUNCTION
Press button B9 to the 2nd step for extra function .
SLOW SPEED (MICRO) OPERATION and EXTRA FUNCTION
(only 8B & 10B)
Button B10 1st step: Micro
Push in the button for Slow speed (micro) and the LED for Slow speed will be
lit. The objects motion will now only operate at a factory pre-set slow speed
regardless of the compression of the push buttons. The buttons are interlocked
during this time so that only one movement can be operated at a time. The
other functions work normally.
Button B10 2nd step: Extra function
Push in the button for extra function.
ROTARY SWITCH (only 9BRS)
Set the rotary switch in desired position for function.
Operating Manual JUPITER 8B, 9BRS & 10B 7 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
SELECTION 1, 2 or 1+2 (9BRS & 10B only)
Press button (B7) for selection 1 and/or button (B8) for selec-
tion 2, respective button LED indicates the selection that is active.
These functions can be used for optional choices such as trolley or crane
selection. These buttons are congured as remaining.
DUPLEX
In a duplex system the transmitter gets information from the receiver and
shows it on the display, for example weight.
See “Display indications (only 9BD RS & 10BD)” on page 9.
STOP
Depress the safety STOP button for stop.
TRANSMITTER & MAIN CONTACTOR OFF
Depress the STOP button which switches off the transmitter. At the same time
the main contactor in the receiver is deactivated (the main contactor of the
crane cuts out). The status indicator light goes out.
AUTOMATIC SWITCH-OFF FUNCTION
The transmitter is equipped with automatic switch-off function, switching
off the transmitter after 2, 5, or 15 minutes after the latest use. It is also
possible to set the transmitter for continuous operation. The status indicator
goes out and the main contactor is deactivated upon automatic switch-off.
See the Installation manual for instructions how to set the automatic switch-
off time.
Operating Manual JUPITER 8B, 9BRS & 10B 8 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
INDICATIONS
If the transmitter during start up (if not PIN locked) or while in operation
detects a fault in any of the transmitters self-tests it will indicate a continuous
red light. After that the transmitter powers down. If one of the push buttons
has a fault during start-up it indicates a continuous red light for 3 seconds after
that the transmitter powers down.
INDICATIONS EXPLANATIONS
Greenashing Operating
Yellowquickashing Battery voltage low <3,5 V
Yellow continuous, during operating Battery empty
Transmitter will shut-off within 30s
Yellow continuous, at start-up Congurationmode
Red continuous at start-up
+ two top button LED
PIN locked
Red continuous, during operating Hardware fault
Operating Manual JUPITER 8B, 9BRS & 10B 9 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
Display indications (only 9BD RS & 10BD)
These symbols appear on the display by default.
7
12
6
3
5
4
1. Radio signal / MC
2. Texteld(craneidetc.)
3. Battery level
4. Weight, up to 5 digits
5. Weight unit (kg,t or lb)
6. Weight load graph (full-scale=max load)
7. Overload warning
Radio signal quality
This function is only available on duplex systems.
Depending on the application this symbol can be enabled or disabled.
No radio link
established Weak signal Good signal Strong signal Very
strong signal
MC on is indicated by a line beneath the radio signal symbol, example .
Text eld (crane id etc.)
This text is congured in the receiver (8 characters). For knowing which
crane the transmitter is controlling.
Battery level
Depending on the application this symbol can be enabled or disabled.
Battery empty 25% 50% 75% 100% (fully charged)
Weight / Graph / Overload
The weight is shown with the unit symbol kg,ton or lb depending on the
receiver conguration.
The bar graph displays the weight load. Full scale= maximum load. The
graph is only shown if a maximum weight limit is congured in the receiver.
This symbol appears if the load on the crane reaches the weight limit
(overload)
Operating Manual JUPITER 8B, 9BRS & 10B 10 (32)
Jupiter 800/900 8B, 9B RS & 10B Document-ID: 948682-000 EN/SV
Version: B0 Author: SH
EN
BATTERY
The transmitter is equipped with a status indicator showing battery status.
The indicator blinks slowly green when the battery voltage is normal, but
starts to blink rapidly yellow, when it gets low. When the indicator has started
blinking rapidly yellow, the transmitter can be operated for approximately
5-10 minutes before the voltage is so low that the transmitter switches off
automatically.
Disposal of a Li-Ion battery poses a smaller threat to the environ-
ment when compared to other battery types. All used Li-Ion bat-
teries should be immediately sent to a qualied battery collection
centre for recycling.
• Remove the battery from the charger when the power supply is turned off.
• A well maintained battery is necessary for faultless operation.
!The battery must not be charged if the temperature is lower than
+10ºC or higher than +45ºC.
!Only use chargers approved by the supplier.
!
Warning! If an incorrect battery type is used in the unit, the battery
may explode.
CHARGER INSTRUCTIONS
Please read the documentation supplied with the charger for charging instructions.
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Sprachen:
Andere Akerstroms Fernbedienung Handbücher
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms Remotus Jupiter Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 L15 Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms JUPITER 100J Bedienungsanleitung
Akerstroms
Akerstroms Jupiter Era 4B Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 MOBILE TAIL LIFT Bedienungsanleitung
Akerstroms
Akerstroms Remotus Jupiter Era 4 Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Akerstroms
Akerstroms T-Rx 1000 Bedienungsanleitung
Akerstroms
Akerstroms Jupiter Era 10BD Bedienungsanleitung
Akerstroms
Akerstroms Jupiter Era 4B Bedienungsanleitung
Akerstroms
Akerstroms SESAM 800 CONFIGURABLE Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
