AKM AKD4633-A Bedienungsanleitung

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 1 -

GENERAL DESCRIPTION

AKD4633-A is an evaluation board for the AK4633VN, 16bit mono CODEC with MIC/SPK amplifier. The

AKD4633-A can evaluate A/D converter and D/A converter separately in addition to loopback mode (A/D

D/A). AKD4633-A also has the digital audio interface and can achieve the interface with digital audio

systems via opt-connector.

Ordering guide

AKD4633-A ---Evaluation board for AK4633VN

(Cable for connecting with an USB port and control software is packed with this.)

FUNCTION

DIT/DIR with optical input/output

BNC connector for an external clock input

10pin Header for serial control mode

10pin Header

Control Data

10pin Header

GND

BEEP/MIN/MOUT

AK4114 Opt In

Opt Out

Clock

Gen

AK4633VN

SVDDAVDD

DSP

DVDD

MIC-Jack

SPK-Jack

AOUT

MIC

5V Regulator

3.3V

Figure 1. AKD4633-A Block Diagram

* Circuit diagram and PCB layout are attached at the end of this manual.

AK4633 Evaluation board Rev.3

AKD4633

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 2 -

Evaluation Board Manual

Operation sequence

1) Set up the power supply lines.

1-1) When AVDD,DVDD, SVDD, and VCCare supplied from the regulator. (AVDD, DVDD, SVDD, and VCC

jack should be open.). See “Other jumper pins set up (page 10)”. <default>

[REG] (red ) = 5V

[AVDD] (orange) = open : 3.3V is supplied to AVDD of AK4633VN from regulator.

[DVDD] (orange) = open : 3.3V is supplied to DVDD of AK4633VN from regulator.

[SVDD](blue) = open : 3.3V is supplied to SVDD of AK4633VN from regulator.

[VCC] (orenge) = open : 3.3V is supplied to logic block from regulator.

[AVSS] (black) = 0V : for analog ground

[AGND] (black) = 0V : for analog ground

[DGND] (black) = 0V : for logic ground

1-2) When AVDD, DVDD, SVDD, and VCC are not supplied from the regulator. (AVDD, DVDD, SVDD, and

VCC jack should be junction.) See “Other jumper pins set up (page 10)”.

[REG] (red) = “REG” jack should be open.

[AVDD] (orange) = 2.6 3.6V : for AVDD of AK4633VN (typ. 3.3V)

[DVDD] (orange) = 2.6 3.6V : for DVDD of AK4633VN (typ. 3.3V)

[SVDD] (blue) = 2.6 5.25V: for SVDD of AK4633VN (typ. 3.3V, 5.0V)

[VCC] (orenge) = 2.6 3.6V : for logic (typ. 3.3V)

[AVSS] (black) = 0V : for analog ground

[AGND] (black) = 0V : for analog ground

[DGND] (black) = 0V : for logic ground

Each supply line should be distributed from the power supply unit.

AVDD and DVDD must be same voltage level.

2) Set up the evaluation mode, jumper pins and DIP switches. (See the followings.)

3) Power on.

The AK4633VN and AK4114 should be reset once bringing SW1, 2 “L” upon power-up.

Evaluation mode

In case of AK4633VN evaluation using AK4114, it is necessary to correspond to audio interface format for

AK4633VN and AK4114. About AK4633VN’s audio interface format, refer to datasheet of AK4633VN.

About AK4114’s audio interface format, refer to Table 2 in this manual.

Applicable Evaluation Mode

(1) Evaluation of loop-back mode (A/D D/A) : PLL, Master Mode

(2) Evaluation of loop-back mode (A/D D/A) : PLL, Slave Mode (PLL Reference CLOCK: MCKI

pin)

(3) Evaluation of loop-back mode (A/D D/A) : PLL, Slave Mode (PLL Reference CLOCK: BICK or

FCK pin)

(4) Evaluation of using DIR of AK4114 (opt-connector) : EXT, Slave Mode

(5) Evaluation of using DIT of AK4114 (opt-connector) : EXT, Slave Mode

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 3 -

(1) Evaluation of loop-back mode (A/D D/A) : PLL, Master Mode

a) Set up jumper pins of MCKI clock

X’tal of 11.2896MHz, 12MHz, 12.288MHz, 13MHz, 24MHz or 27MHz can be set in X2. X’tal of 12.288MHz

(Default) is set on the AKD4633VN. Set “No.8 of SW3” to “H”.

When an external clock (11.2896MHz, 12MHz, 12.288MHz, 13MHz, 24MHz or 27MHz) through a RCA

connector (J8: EXT/BICK) is supplied, select EXT on JP21 (MCLK_SEL) and short JP17 (XTE). JP23 (EXT1)

and R26 should be properly selected in order to much the output impedance of the clock generator.

b) Set up jumper pins of BICK clock

Output frequency (16fs/32fs/64fs) of BICK should be set by “BCKO1-0 bit” in the AK4633VN.

There is no necessity for set up JP19.

c) Set up jumper pins of FCK clock

d) Set up jumper pins of DATA

When the AK4633VN is evaluated by loop-back mode (A/D D/A), the jumper pins should be set to the

following.

JP17

XTE MCLK_SEL

JP21 JP18

MKFS

256fs 512fs1024fs

XTL DIR EXT MCKO

JP6

MCKI

JP22

FCK_SEL

2fs EXT

JP28

FCK

ADCDIR

1fs

JP26

4631_SDTI

ADC

DAC/LOOP

JP30

SDTI

DIR ADC

JP29

JP20

BICK JP27 BICK_INV

THRINV DIR ADC

BICK

THRINV

BICK_SEL

JP19

EXT

16fs

32fs

64fs

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 4 -

(2) Evaluation of loop-back mode (A/D D/A) : PLL, Slave Mode (PLL Reference CLOCK: MCKI pin)

a) Set up jumper pins of MCKI clock

X’tal of 12.288MHz (Default) is set on the AKD4633-A. In this case, the AK4633VN corresponds to PLL

reference clock of 12.288MHz. In this evaluation mode, the output clock from MCKO-pin of the AK4633VN is

supplied to a divider (U3: 74VHC4040), BICK and FCK clocks are generated by the divider. Then “MCKO bit”

in the AK4633VN should be set to “1”. When an external clock through a RCA connector (J8: EXT/BICK) is

supplied, select EXT on JP21 (MCLK_SEL) and short JP17 (XTE). JP23 (EXT1) and R26 should be properly

selected in order to match the output impedance of the clock generator.

b) Set up jumper pins of BICK clock

c) Set up jumper pins of FCK clock

d) Set up jumper pins of DATA

When the AK4633VN is evaluated by loop-back mode (A/D D/A), the jumper pins should be set to the

following.

JP17

XTE MCLK_SEL

JP21 JP18

MKFS

256fs 512fs1024fs

XTL DIR EXT MCKO

JP6

MCKI

JP28

FCK

ADCDIR

JP22

FCK_SEL

2fs EXT1fs

JP26

4631_SDTI

ADC

DAC/LOOP

JP30

SDTI

DIR ADC

JP29

JP20

BICK JP27 BICK_INV

THRINV DIR ADC

BICK

THRINV

BICK_SEL

JP19

EXT

16fs

32fs

64fs

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 5 -

(3) Evaluation of loop-back mode (A/D D/A) : PLL, Slave Mode (PLL Reference CLOCK: BICK or FCK

pin)

a) Set up jumper pins of BICK clock

When an external clock through a RCA connector J8 (EXT/BICK) is supplied, select EXT on JP19

(MCLK_SEL) and short JP17 (XTE). JP23 (EXT1) and R26 should be properly selected in order to match the

output impedance of the clock generator.

In this evaluation mode, the selected clock from JP21 (MCLK_SEL) is supplied to a divider (U3: 74VHC4040),

BICK and FCK clocks are generated by the divider. Input frequency of master clock is set up in turn “256fs”,

“512fs”, “1024fs” from left.

And input frequency of BICK is set up in turn “16fs”, “32fs”, “64fs” from left.

JP17

XTE MCLK_SEL

JP21

XTL DIR EXT

JP29

JP20

BICK JP27 BICK_INV

THRINV DIR ADC

BICK

THRINV

JP18

MKFS

256fs 512fs1024fsMCKO

JP18

MKFS

256fs 512fs1024fsMCKO

JP18

MKFS

256fs 512fs1024fsMCKO

BICK_SEL

JP19

EXT16fs32fs64fs

BICK_SEL

JP19

EXT16fs32fs64fs

BICK_SEL

JP19

EXT16fs32fs64fs

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 6 -

b) Set up jumper pins of FCK clock

When an external clock through a RCA connector J9 (FCK) is supplied, select EXT on JP22 (FCK_SEL). JP24

(EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.

c) Set up jumper pins of DATA

When the AK4633VN is evaluated by loop-back mode (A/D D/A), the jumper pins should be set to the

following.

JP28

FCK

ADCDIR

JP22

FCK_SEL

2fs EXT1fs

JP26

4633_SDTI

ADC

DAC/LOOP

JP30

SDTI

DIR ADC

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 7 -

(4) Evaluation of using DIR of AK4114 (opt-connector) : EXT, Slave Mode

a) Set up jumper pins of MCKI clock

b) Set up jumper pins of BICK clock

c) Set up jumper pins of FCK clock

JP24 (EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.

d) Set up jumper pins of DATA

When D/A converter of the AK4633VN is evaluated by using DIR of AK4114, the jumper pins should be set to

the following.

JP17

XTE MCLK_SEL

JP21

XTL DIR EXT

JP6

MCKI JP18

MKFS

256fs 512fs1024fs

JP29

JP20

BICK JP27 BICK_INV

THRINV DIR ADC

BICK

THRINV

BICK_SEL

JP19

EXT

16fs32fs

64fs

JP28

FCK

ADCDIR

JP22

FCK_SEL

2fs EXT1fs

JP26

4633_SDTI

ADC

DAC/LOOP

JP30

SDTI

DIR ADC

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 8 -

(5) Evaluation of using DIT of AK4114 (opt-connector) : EXT, Slave Mode

a) Set up jumper pins of MCKI clock

b) Set up jumper pins of BICK clock

c) Set up jumper pins of FCK clock

JP24 (EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.

d) Set up jumper pins of DATA

When A/D converter of the AK4633VN is evaluated by using DIR of AK4114, the jumper pins should be set to

the following.

JP17

XTE MCLK_SEL

JP21

XTL DIR EXT

JP6

MCKI JP18

MKFS

256fs 512fs1024fs

JP28

FCK

ADCDIR

JP22

FCK_SEL

2fs EXT1fs

JP26

4633_SDTI

ADC

DAC/LOOP

JP30

SDTI

DIR ADC

JP29

JP20

BICK JP27 BICK_INV

THRINV DIR ADC

BICK

THRINV

BICK_SEL

JP19

EXT

16fs32fs

64fs

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 9 -

DIP Switch set up

[SW3] (MODE) : Mode Setting of AK4633-VN and AK4114

ON is “H”, OFF is “L”.

No. Name ON (“H”) OFF (“L”)

1 DIF0 AK4114 Audio Format Setting

See Table 2

2 DIF1

3 DIF2

4 CM0 Clock Operation Mode select

See Table 3

5 CM1

6 OCKS0 Master Clock Frequency Select

See Table 4

7 OCKS1

8 M/S Master mode Slave mode

Note. When the AK4633VN is evaluated Master mode, “No.8 of SW3” is set to “H”.

Table 1. Mode Setting for AK4633VN and AK4114

Resistor setting

for AK4633VN Audio

Interface Format Setting for AK4114 Audio Interface Format

DIF1 bit DIF0 bit DIF0 DIF1 DIF2 DAUX SDTO

0 1 L L L 24bit, Left justified 16bit, Right justified

1 0 L L H 24bit, Left justified 24bit, Left justified Default

1 1 H L H 24bit, I2S 24bit, I2S

Note. When the AK4633VN is evaluated by using DIR/DIT of AK4114, “No.8 of SW3” is set to “L”.

Table 2. Setting for AK4114 Audio Interface Format

Mode CM1 CM0 UNLOCK PLL X'tal Clock source SDTO

0 0 0 - ON ON(Note) PLL RX

1 0 1 - OFF ON X'tal DAUX

2 1 0 0 ON ON PLL RX Default

1 ON ON X'tal DAUX

3 1 1 - ON ON X'tal DAUX

ON: Oscillation (Power-up), OFF: STOP (Power-down)

Note : When the X’tal is not used as clock comparison for fs detection (i.e. XTL1,0= “1,1”), the X’tal is off.

Default setting is recommended.

Table 3. Clock Operation Mode select

No. OCKS1 MCKO1 MCKO2 X’tal Default

0 0 256fs 256fs 256fs

2 1 512fs 256fs 512fs

Table 4. Master Clock Frequency Select (Stereo mode)

ASAHI KASEI [AKD4633-A]

<KM079407> 2016/10

- 10 -

Other jumper pins set up

1. JP1 (GND) : Analog ground and Digital ground

OPEN : Separated.

SHORT : Common. (The connector “DGND” can be open.) <Default>

2. JP2 (MICP) : Connection between MICP pin and BEEP pin of the AK4633VN.

MICP : MIC Differential input.

BEEP : BEEP input. <Default>

3. JP3 (AVDD_SEL) : AVDD of the AK4633VN

REG : AVDD is supplied from the regulator (“AVDD” jack should be open). < Default >

AVDD : AVDD is supplied from “AVDD ” jack.

4. JP9 (DVDD_SEL) : DVDD of the AK4633VN

AVDD : DVDD is supplied from “AVDD”. < Default >

DVDD : DVDD is supplied from “DVDD ” jack.

5. JP10 (LVC_SEL) : Logic block of LVC is selected supply line.

DVDD : Logic block of LVC is supplied from “DVDD”. < Default >

VCC : Logic block of LVC is supplied from “VCC ” jack.

6. JP11 (VCC_SEL) : Logic block is selected supply line.

LVC : Logic is supplied from supply line of LVC. < Default >

VCC : Logic block of LVC is supplied from “VCC ” jack.

7. JP4 (SVDD_SEL) : SVDD of the AK4633VN

REG : SVDD is supplied from the regulator (“SVDD” jack should be open). < Default >

SVDD : SVDD is supplied from “SVDD ” jack.

8. JP8 (MCKO_SEL) : Master Clock Frequency is selected clock from MCKO1 or MCKO2 of the AK4114.

MCKO1 : The check from MCKO1 of AK4114 is provided to MCKI of the AK4633VN. < Default >

MCKO2 : The check from MCKO2 of AK4114 is provided to MCKI of the AK4633VN.

Andere AKM Hauptplatine Handbücher

AKM

AKM AK4621 Bedienungsanleitung

AKM

AKM AKD4128A-A Bedienungsanleitung

AKM

AKM AKD4133-A Bedienungsanleitung

AKM

AKM AKD4589-B Bedienungsanleitung

AKM

AKM AKD4558-A Bedienungsanleitung

AKM

AKM AK5394A Bedienungsanleitung

AKM

AKM AKD4497-SA Bedienungsanleitung

AKM

AKM AKD4951AEN-B Bedienungsanleitung

AKM

AKM AKD4953-A Bedienungsanleitung

AKM

AKM AKD4558-A Bedienungsanleitung

AKM

AKM AKD4556-B Bedienungsanleitung

AKM

AKM AKD4344-A Bedienungsanleitung

AKM

AKM AKD4385-SC Bedienungsanleitung

AKM

AKM AKD4637-B Bedienungsanleitung

AKM

AKM AsahiKASEl AK7600VF Bedienungsanleitung

AKM

AKM AK4584 Bedienungsanleitung

AKM

AKM AKD4103A-B Bedienungsanleitung

AKM

AKM AKD5356 Bedienungsanleitung

AKM

AKM AKD4114-B Bedienungsanleitung

AKM

AKM AKD4629-A Bedienungsanleitung

AKM

AKM AKD4688-A Bedienungsanleitung

AKM

AKM AK4115 Bedienungsanleitung

AKM

AKM AKD4432-SA Bedienungsanleitung

AKM

AKM AKD4753-A Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung