AKO AKO-55326 Bedienungsanleitung
Warnings
The alarm and pushbuttons must be installed in a place protected from vibrations, water and corrosive
gases, where the ambient temperature does not exceed the value indicated in the technical data.
The station must be installed in a place where the regular presence of people who can alert to the presence of alarms
is guaranteed.
Neither the alarm nor the pushbutton are suitable for areas classified as potentially explosive.
The pushbutton must be installed inside the cold room, in a visible place and no higher than 125 cm from the
ground.
Wiring
15V
In
Gnd
Input x
ALARM STATION
OUT
15V
Indicator lights
Alarm Pushbutton
5532H602 Ed.01
GB
AKO-55326
AKO ELECTROMECÁNICA , S.A.L.
Avda. Roquetes, 30-38
08812 • Sant Pere de Ribes.
Barcelona • Spain.
Tel.: +34 902 333 145
Fax: +34 938 934 054
www.ako.com
We reserve the right to supply materials that might vary slightly to those described in
our Technical Sheets. Updated information is available on our website
355532602 Rev 00 2017
Trapped person alarm push-button.
Quick guide
Always disconnect the power supply to do the
wiring.
The wiring between the pushbutton and the station
must NEVER be installed in a conduit together with
power, control or power supply cables.
Configuration
Use in: AKO-55424 / AKO-555241 / AKO-555242 / AKO-558241 / AKO-558242
Step 1:
Once the pushbutton has been connected, connect the power supply of the station. Before 2 minutes have passed,
press the “AUTOCONFIG” pushbutton 5 consecutive times.
Step 2:
Press the “AUTOCONFIG” pushbutton for 5 seconds; the alarm will emit 5 short tones. Configuration is completed.
For a correct detection of inputs, all devices must be correctly connected and in NO ALARM mode, including
the devices connected in digital inputs.
Once configured, the display shows the indicator corresponding to the device detected at each input in green:
Luminous pushbutton
Use in: AKO-55323 / AKO-55123 / AKO-55120
The unit is supplied as ready-to-use; no configuration is required
Operation
Activating the alarm Deactivating the alarm
Press the alarm pushbutton Slightly rotate the alarm pushbutton in the clockwise
direction.
x5
ON
OFF
1
2
5"
Maintenance
Clean the surface of the unit with a soft cloth, water and
soap.
Do not use abrasive detergents, petrol, alcohol or
solvents, as this might damage the sensor.
Technical specifications
Power supply......................................15 Vdc ± 3 Vdc
Working ambient temperature............-50 ºC to 50 ºC
Storage ambient temperature .............-50 ºC to 70 ºC
Protection degree ..............................................IP 65
Installation category..............................II s/ EN 61010-1
Pollution degree....................................II s/ EN 61010-1
Maximum pushbutton wiring distance ..................300 m
Dimensions ......202 mm (W) x 82 mm (H) x 84.4 mm (D)
Inhaltsverzeichnis
Andere AKO Sicherheitssystem Handbücher
AKO
AKO AKO-55326 Bedienungsanleitung
AKO
AKO 52067 Bedienungsanleitung
AKO
AKO AKO-55424 Bedienungsanleitung
AKO
AKO 5206 Bedienungsanleitung
AKO
AKO AKO-55424 Bedienungsanleitung
AKO
AKO AKO-52062 Bedienungsanleitung
AKO
AKO 55424 Bedienungsanleitung
AKO
AKO 52041 Bedienungsanleitung
AKO
AKO 55624 Bedienungsanleitung
AKO
AKO 522044 Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung