Alarm Lock AL-DTM-III Kurzanleitung

AL-DTM-III

SETUP & CONFIGURATION INSTRUCTIONS

345 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs, (800) 645-9445

For Technical Service, (800) 645-9440 © ALARM LOCK 2005 Publicly traded on NASDAQ Symbol: NSSC WI1443A 10/05

ALARM LOCK

AL-DTM-III SETUP

Configure the internal DTM software for DTM-III op-

eration:

1. From the Power On or PC Comm. mode, press and

HOLD both the left and green buttons on the DTM.

After several messages appear, release the buttons

when the display reads:

2. When the display reads "CONFIG. LANGUAGE", the

DTM has entered its configuration and self-test

mode.

3. Press and release the green button once and the dis-

play will read "CONFIG FOR DTM-III MODE".

4. Press and HOLD the green button until the DTM

beeps--release the button and the display reads:

The top line of the display indicates that DTM-III

mode is currently off; the bottom line corresponds to

the three buttons on the DTM.

Therefore, to activate DTM-III operation, press the

left button. The top line of the display will now read:

(Note: If using DL-Windows versions earlier than

3.5.3, you must press the center button to keep

DTM-III operation off--thus retaining DTM-II opera-

tion).

5. Press the green button to exit this sequence. "TASK

ENDING!" will appear briefly. The DTM will proceed

directly to "Door Selection Mode" as described in the

next section.

ENABLE DOOR SELECTION MODE

Door Selection Mode is only needed if performing

initial lock programming using DL-Windows 3.5.3.

See the DL-Windows User's Guide OI237 for more

information about Door Selection Mode.

1. When configuring to allow Door Select Mode, the dis-

play will switch between the following:

2. Press and HOLD the green button until the DTM

beeps--release the button and the DTM will display:

The top line of the display indicates that Door Select

mode is currently off; the bottom line corresponds to

the three buttons on the DTM.

Therefore, if using DL-Windows Version 3.5.3 or later

and you wish to use the AL-DTM-III to provide initial

programming to existing locks, press the left button

(selecting "ON") to enable DOOR SELECT Mode.

The top line of the display will

now read:

(Note: You may press the

center button to keep Door Select mode off, provided

all system locks are already enrolled in the DL-

Windows 3.5.3 program. See the DL-Windows User

Guide for details regarding Door Select mode).

3. Press and release the green button (again and

again) until the DTM Displays:

4. Press and hold the green button until the DTM

Beeps. The DTM will perform a brief power control

test (TEST RUNNING!) and then shut down within 5

seconds.

Release the

buttons when

displayed

Data Transfer Modules allow the transfer of lock programs and other data between DL-Windows software and Alarm Lock locking de-

vices. The improved DTM-III allows for more locks to be stored per account, both within DL-Windows and within the DTM-III itself. These

instructions will allow you to configure for the improved DTM-III operation.

DTM's that start up with the message "Alarm Lock DTM-II-III, V1.XX" will operate in both the DTM-II and DTM-III modes. Units

configured to operate in DTM-III mode will display "DTM-III" when prompting users to enter Lock Mode. The DTM-III mode is required for

DL-Windows 3.5.3 operation, and likewise DL-Windows 3.5.3 is required for use with DTM-III mode. Note: If you are unsure about your

version of DL-Windows, version numbers can be found in the DL-Windows Help, About screen. Products shipped as DTM-III have been

factory configured for DTM-III mode ON and Door Select Mode OFF.

(over →)

ENTERING

CONFIG/TEST MODE

DTM-III MODE=OFF

ON OFF EXIT

DTM-III MODE=ON

ON OFF EXIT

CONFIG. DOOR

SELECT MODE

Hold Button=Run,

Press=Next Test

DOOR SELECT= OFF

ON OFF EXIT

Sleep Then

Power Down.

DOOR SELECT= ON

ON OFF EXIT

DOOR SELECTION OVERVIEW

Door Numbers and Lock ID's

Prior to DL-Windows v3.5.3, Door Numbers were

used to ensure that each physical lock was correctly

matched to its corresponding data when programmed.

Door Numbers were programmable via the lock key-

pad via Function 59 (for locks without keypads, such

as the PL3000, Door Numbers were selected either

by a DL-Windows equipped PC or by the Door Select

function of an AL-DTM-II. See WI1280 for more infor-

mation).

With DL-Windows v3.5.3 or later, the concept of a

Door Number has been discontinued in favor of a new

system of LockID's. With LockID's, changing the Door

Number at the keypad via Function 59 is ignored by

DL-Windows, and the ONLY way to ensure the cor-

rect physical locks are properly matched to their cor-

responding data is to either:

•use DL Windows v3.5.3 to program the locks, thus

updating the locks with the new "LockID" system,

--or--

•use an AL-DTM-III and its Door Select Mode to

provide the full lock program (which includes the

LockID).

Note: The DTM displays the word "Door" and not

"LockID" when referring to door numbers. In the

DTM, both words are equivalent.

USING DOOR SELECT MODE

To use an AL-DTM-III to program locks for the first

time using Door Select Mode, proceed as follows:

1. Power up the AL-DTM. Upon pressing the green

power-up button, the DTM displays several mes-

sages, including the DTM ID and version number,

a memory test, and its total memory status.

Then a prompt for the Operation Mode will ap-

pear:

Press the left black button (below Select) to en-

able Door Select Mode in addition to the two

other modes of operation (PC Comm Mode and

Lock Mode). The following screen appears, indi-

cating the DTM is now in PC Communication

Mode:

2. Download the lock data from the PC to the DTM

(the PC must be running DL-Windows 3.5.3 or

later). This lock data will be the data intended to

be sent to the locks. Refer to the DL-Windows

manual OI237 for the full procedure.

3. Press the green button until the display reads as

follows:

Press the left button (below YES) to use the Door

Select Mode. A "Test Running" message may

briefly appear (and re-appear) in the display.

4. The first of the available door numbers will appear

(as shown in the sample screen below). In the be-

low example, the current door number (also

named LockID in DL-Windows) is "8".

Note: If there are no available doors loaded in the

DTM, the display will read "CLR", as shown in the

following screen:

5. Scroll through the available door numbers

(previously downloaded in step 2) by pressing the

BACK and NEXT buttons.

6. When the desired door number is in the display, (6

in the example screen below) press the button be-

low SET to select. The following will display.

7. Connect the DTM to the lock via the double-ended

mini banana plug. Press the left button (GO) and

the following screen will display, prompting you to

enter the Function 299 download code (or for PL

"keypadless" locks, to present the Function 2

card):

Enter the lock's Function 299 code (or for PL

locks, present the Function 2 card) to initiate the

data transfer. The DTM will perform a quick test

of the lock as the following screens appear

DOOR SELECT MODE

YES NO

Current Door=008

<BACK NEXT> SET

Ready, Door =006

GO EXIT

OPERATION MODE?

SELECT STD.

PC COMM MODE

. . . .

Current Door=CLR

<BACK NEXT> SET

DTM-III: Plug in

then enter code

No lock detected

10/10/06 03:45PM

Re-enter the Function 299 code a second time, (or

re-present Function Card 2 for PL series locks)

and the following screen appears during

download:

(Packet numbers will increase until all packets

have been transferred to the lock). The Lock will

continue to beep while in communication with the

AL-DTM.

8. At the end of the transfer process, the lock will

sound a series of beeps. You can now disconnect

the mini banana plug. The following will display:

9. The DTM will then provide a memory status and

proceed to the following Lock Mode screen:

To start again, press the right button (below NO)

to exit Lock Mode and then press the left button

(below YES) to use Door Select Mode.

Continue again at step 3, above.

Note: The AL-DTM will only allow the selection of a

"door number" for which it has valid data currently

programmed (step 2, above, must be performed).

Warning: The "door number" (LockID) selected will

override the number (if any) programmed in the

lock. Care must be taken to ensure that the cor-

rect data is being transferred to the correct lock.

Door 08, Sending

PGM Packet 005

Com. Complete

10/10/06 03:47PM

LOCK MODE

YES NO

DOOR SELECT MODE

YES NO

Door ****

Detected

Re-enter 299 code

to continue

ALARM LOCK SECURITY SYSTEMS, INC. (ALARM

LOCK) warrants its products to be free from

manufacturing defects in materials and workmanship for

24 months following the date of manufacture. ALARM

LOCK will, within said period, at its option, repair or

replace any product failing to operate correctly without

charge to the original purchaser or user.

This warranty shall not apply to any equipment, or

any part thereof, which has been repaired by others,

improperly installed, improperly used, abused, altered,

damaged, subjected to acts of God, or on which any

serial numbers have been altered, defaced or removed.

Seller will not be responsible for any dismantling or

reinstallation charges.

THERE ARE NO WARRANTIES, EXPRESS OR

IMPLIED, WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE HEREOF. THERE IS

NO EXPRESS OR IMPLIED WARRANTY OF

MERCHANTABILITY OR A WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE. ADDITIONALLY,

THIS WARRANTY IS IN LIEU OF ALL OTHER

OBLIGATIONS OR LIABILITIES ON THE PART OF

ALARM LOCK.

Any action for breach of warranty, including but not

limited to any implied warranty of merchantability, must

be brought within the six months following the end of the

warranty period.

IN NO CASE SHALL ALARM LOCK BE LIABLE TO

ANYONE FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES FOR BREACH OF THIS OR

ANY OTHER WARRANTY, EXPRESS OR IMPLIED,

EVEN IF THE LOSS OR DAMAGE IS CAUSED BY

THE SELLER'S OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional

who installed and maintains your security system. In

order to exercise the warranty, the product must be

returned by the security professional, shipping costs

prepaid and insured to ALARM LOCK. After repair or

replacement, ALARM LOCK assumes the cost of

returning products under warranty. ALARM LOCK shall

have no obligation under this warranty, or otherwise, if

the product has been repaired by others, improperly

installed, improperly used, abused, altered, damaged,

subjected to accident, nuisance, flood, fire or acts of

God, or on which any serial numbers have been altered,

defaced or removed. ALARM LOCK will not be

responsible for any dismantling, reassembly or

reinstallation charges.

This warranty contains the entire warranty. It is the

sole warranty and any prior agreements or

representations, whether oral or written, are either

merged herein or are expressly canceled. ALARM

LOCK neither assumes, nor authorizes any other person

purporting to act on its behalf to modify, to change, or to

assume for it, any other warranty or liability concerning

its products.

In no event shall ALARM LOCK be liable for an

amount in excess of ALARM LOCK's original selling

price of the product, for any loss or damage, whether

direct, indirect, incidental, consequential, or otherwise

arising out of any failure of the product. Seller's warranty,

as hereinabove set forth, shall not be enlarged,

diminished or affected by and no obligation or liability

shall arise or grow out of Seller's rendering of technical

advice or service in connection with Buyer's order of the

goods furnished hereunder.

ALARM LOCK RECOMMENDS THAT THE ENTIRE

SYSTEM BE COMPLETELY TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but not

limited to, any or all of the following; criminal tampering,

electrical or communications disruption, it is possible for

the system to fail to perform as expected. ALARM LOCK

does not represent that the product/system may not be

compromised or circumvented; or that the product or

system will prevent any personal injury or property loss

by burglary, robbery, fire or otherwise; nor that the

product or system will in all cases provide adequate

warning or protection. A properly installed and

maintained alarm may only reduce risk of burglary,

robbery, fire or otherwise but it is not insurance or a

guarantee that these events will not occur.

CONSEQUENTLY, SELLER SHALL HAVE NO

LIABILITY FOR ANY PERSONAL INJURY,

PROPERTY DAMAGE, OR OTHER LOSS BASED ON

A CLAIM THE PRODUCT FAILED TO GIVE

WARNING. Therefore, the installer should in turn advise

the consumer to take any and all precautions for his or

her safety including, but not limited to, fleeing the

premises and calling police or fire department, in order to

mitigate the possibilities of harm and/or damage.

ALARM LOCK is not an insurer of either the property

or safety of the user's family or employees, and limits its

liability for any loss or damage including incidental or

consequential damages to ALARM LOCK's original

selling price of the product regardless of the cause of

such loss or damage.

Some states do not allow limitations on how long an

implied warranty lasts or do not allow the exclusion or

limitation of incidental or consequential damages, or

differentiate in their treatment of limitations of liability for

ordinary or gross negligence, so the above limitations or

exclusions may not apply to you. This Warranty gives

you specific legal rights and you may also have other

rights which vary from state to state.

ALARM LOCK LIMITED WARRANTY

Inhaltsverzeichnis

Andere Alarm Lock Computerhardware Handbücher

Alarm Lock

Alarm Lock SE-DTM Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung