Alcatel-Lucent OmniSwitch 6850-48 Bedienungsanleitung

OmniSwitch 6850 Series

Getting Started Guide

060208-10, Rev. C

June 2007

Warning. Only personnel knowledgeable in basic electrical and mechanical procedures should install or maintain this

equipment.

Lithium Batteries Caution. There is a danger of explosion if the Lithium battery in your chassis is incorrectly replaced.

Replace the battery only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used

batteries according to the manufacturer’s instructions. The manufacturer’s instructions are as follows:

The features and specifications described in this guide are subject to change without notice.

the express written permission of Alcatel-Lucent.

Alcatel-Lucent®and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. Xylan®, OmniSwitch®,

OmniStack®, and Alcatel-Lucent OmniVista®are registered trademarks of Alcatel-Lucent.

OmniAccess™, Omni Switch/Router™, PolicyView™, RouterView™, SwitchManager™, VoiceView™, WebView™,

X-Cell™, X-Vision™, and the Xylan logo are trademarks of Alcatel-Lucent.

This OmniSwitch product contains components which may be covered by one or more of the following U.S. Patents:

• U.S. Patent No. 6,339,830

• U.S. Patent No. 6,070,243

• U.S. Patent No. 6,061,368

• U.S. Patent No. 5,394,402

• U.S. Patent No. 6,047,024

• U.S. Patent No. 6,314,106

• U.S. Patent No. 6,542,507

• U.S. Patent No. 6,874,090

Return the module with the Lithium battery to Alcatel-Lucent. The Lithium

battery will be replaced at Alcatel-Lucent’s factory.

Alcatel-Lucent

26801 West Agoura Road

Calabasas, CA 91301

(818) 880-3500 FAX (818) 880-3505

US Customer Support: (800) 995-2696

International Customer Support: (818) 878-4507

Internet: service.esd.alcatel-lucent.com

June 2007 iii

OmniSwitch 6850 Series. . . . . . . . . . . . . . . 1

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing the Hardware . . . . . . . . . . . . . . . 3

Items Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Environmental Requirements . . . . . . . . . . . . . . . 3

Electrical Requirements . . . . . . . . . . . . . . . . . . . 3

NEBS GR-1089 Compliance Requirements . . . . 3

Weight Considerations . . . . . . . . . . . . . . . . . . . . 4

Items Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking and Initial Setup . . . . . . . . . . . . . . . . . . . 5

Unpacking the Chassis . . . . . . . . . . . . . . . . . . . . 5

Recommendations . . . . . . . . . . . . . . . . . . . . 5

Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setting Up the Switch . . . . . . . . . . . . . . . . . . . . . . . . 6

Airflow Considerations . . . . . . . . . . . . . . . . . . . . 6

Installation Options . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the Switch on a Tabletop or Bench . . . 7

Tabletop Mounting Steps . . . . . . . . . . . . . . . 7

Rack-Mounting the Switch . . . . . . . . . . . . . . . . . 8

Rack Mounting Steps . . . . . . . . . . . . . . . . . . 8

Installing Combo Port SFPs . . . . . . . . . . . . . . . . . . 10

Installing Backup Power Supply Components . . . . 10

Connections and Cabling . . . . . . . . . . . . . 11

Connecting the Serial Cable . . . . . . . . . . . . . . . . . . 11

Serial Connection Default Settings . . . . . . . . . . . . . 11

Booting OmniSwitch 6850 Series

Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Booting a Standalone Switch . . . . . . . . . . . . . . . . . 12

Your First Login Session . . . . . . . . . . . . . . . 14

Logging in to the Switch . . . . . . . . . . . . . . . . . . . . . 14

Assigning an IP Address to the Switch . . . . . . . . . 15

Unlocking Session Types . . . . . . . . . . . . . . . . . . . . 16

Changing the Login Password . . . . . . . . . . . . . . . . 17

Setting the System Time Zone . . . . . . . . . . . . . . . . 18

Setting the Date and Time . . . . . . . . . . . . . . . . . . . . 18

Setting Optional System Information . . . . . . . . . . . 18

Specifying an Administrative Contact . . . . . . .18

Specifying a System Name . . . . . . . . . . . . . . . .19

Specifying the Switch’s Location . . . . . . . . . . .19

Viewing and Saving Changes . . . . . . . . . . . . . . . . . 19

Table of Contents

iv June 2007

Files and Directories. . . . . . . . . . . . . . . . . . . . 20

Boot and Image Files . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

boot.params File . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

boot.cfg File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Image Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Working and Certified Directories . . . . . . . . . . . . . . . . 22

Working Directory . . . . . . . . . . . . . . . . . . . . . . 22

Certified Directory . . . . . . . . . . . . . . . . . . . . . . 23

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . 26

Browser Compatibility . . . . . . . . . . . . . . . . . . . . . . 26

Logging In to WebView . . . . . . . . . . . . . . . . . . . . . 26

Navigating WebView . . . . . . . . . . . . . . . . . . . . . . . 27

Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Additional Information . . . . . . . . . . . . . . . . . . . . . . 29

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

June 2007 OmniSwitch 6850 Series 1

OmniSwitch 6850 Series

The OmniSwitch 6850 Series is an advanced fixed

configuration family of Ethernet switches. These switches

provide wire rate Layer 2 forwarding and Layer 3 routing with

advanced services.

They are fixed configuration, triple-speed (10/100/1000)

switches that provide increased network performance,

improved application response times, secure the LAN, and

enhance user productivity by maximizing mobility, network

capacity, and services over existing category 5/5E/6 cabling.

Refer to the User Manual CD for additional hardware and

software OmniSwitch documentation.

Console

OmniSwitch6850-24

OK PRI PWR BPS

USB

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-P24L

OK PRI PWR BPS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-24L

OK PRI PWR BPS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-48L

OK PRI PWR BPS

CLASS1LASERPRODUCT

1234

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

USB

Console

OmniSwitch6850-P48L

OK PRI PWR BPS

CLASS1LASERPRODUCT

1234

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3536 37 38 39 40 41 42 43 44 45 46 47 48

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

23 24

1 3 5 79 11 13 15 17 19 21 25

10 12 14 16 18 20 22 24

2 4 6 8

USB

Console

OmniSwitch6850-U24X

25 26

OK PRI PWR BPS

CLASS1LASERPRODUCT

Console

OmniSwitch6850-48

OK PRI PWR BPS

CLASS1LASERPRODUCT

1234

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3132 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

1 2 3 4 5 6 7 8 9 1011 12 13 14 1516 17 18 19 20 21 22 23 24

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-24X

25 26

OK PRI PWR BPS

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-48X

OK PRI PWR BPS

CLASS1LASERPRODUCT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 4142 43 44 45 46 47 48

Console

OmniSwitch6850-P24

OK PRI PWR BPS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-P48

OK PRI PWRBPS

CLASS1LASERPRODUCT

1234

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

USB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CLASS1LASERPRODUCT

USB

Console

OmniSwitch6850-P24X

25 26

OK PRI PWR BPS

CLASS1LASERPRODUCT

Console

OmniSwitch6850-P48X

OK PRI PWR BPS

CLASS1LASERPRODUCT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

USB

OmniSwitch 6850-24L

OmniSwitch 6850-24

OmniSwitch 6850-48

OmniSwitch 6850-24X

OmniSwitch 6850-48X

OmniSwitch 6850-P24X

OmniSwitch 6850-P48X

OmniSwitch 6850-P48

OmniSwitch 6850-P24

OmniSwitch 6850-48L

OmniSwitch 6850-P24L

OmniSwitch 6850-P48L

OmniSwitch 6850-U24X

2 OmniSwitch 6850 Series June 2007

Related Documentation

The following are the titles and descriptions of all the

OmniSwitch 6850 Series user documentation included in the

User Manual CD:

•OmniSwitch 6850 Series Getting Started Guide

Describes the hardware and software procedures for

getting an OmniSwitch 6850 Series switch up and

running. Also provides information on fundamental

aspects of OmniSwitch hardware components and

software architecture.

•OmniSwitch 6850 Series Hardware Users Guide

Complete technical specifications and procedures for

all OmniSwitch 6850 Series hardware, including

chassis, power supplies, fans, combo ports, stacking

procedures, optional backup power supplies, etc.

•OmniSwitch CLI Reference Guide

Complete reference to all CLI commands supported on

the OmniSwitch 6850 Series. Includes syntax

definitions, default values, examples, usage

guidelines, and CLI-to-MIB variable mappings.

•OmniSwitch 6800/6850/9000 Switch Management

Guide

Includes procedures for readying a switch for

integration into a network. Topics include the software

directory architecture, image rollback protections,

authenticated switch access, managing switch files,

system configuration, using SNMP, and using web

management software (WebView).

•OmniSwitch 6800/6850/9000 Network Configuration

Guide

Includes network configuration procedures and

descriptive information on all the major software

features and protocols included in the base software

package. Chapters cover Layer 2 information (Ether-

net and VLAN configuration), Layer 3 information

(static routes), security options (authenticated

VLANs), Quality of Service (QoS), and link

aggregation.

•OmniSwitch 6800/6850/9000 Advanced Routing

Configuration Guide

Includes network configuration procedures and

descriptive information on all the software features and

protocols included in the advanced routing software

package. Chapters cover multicast routing (DVMRP

and PIM-SM) and OSPF.

•OmniSwitch Transceivers Guide

Includes information on Small Form Factor Pluggable

(SFPs) and 10 Gbps Small Form Factor Pluggables

(XFPs) transceivers.

June 2007 Installing the Hardware 3

Items Required

In addition to the materials and components provided in the

OmniSwitch 6850 Series shipment, you must provide the

following items in order to complete this installation:

•Grounding wrist strap

•Phillips screwdriver

•Serial cable

•Rack mount screws, if applicable

Site Preparation

Environmental Requirements

OmniSwitch 6850 Series switches have the following environ-

mental and airflow requirements:

•The installation site must maintain a temperature

between 0° and 45° Celsius (32° and 113° Fahrenheit)

and not exceed 95 percent maximum humidity (non-

condensing) at any time.

•Be sure to allow adequate room for proper air

ventilation and access at the front, back, and sides of

the switch. No clearance is necessary at the top or

bottom of the chassis. Refer to page 6 for minimum

clearance requirements.

Electrical Requirements

OmniSwitch 6850 Series switches have the following general

electrical requirements:

•Each switch requires one grounded AC power source.

•Grounded AC power source must be 110V for North

American installations (220V international).

•Each supplied AC power cord is approximately 2

meters (6.5 feet) long. Do not use extension cords.

NEBS GR-1089 Compliance Requirements

The following notes and warnings apply to all NEBS

compliant platforms.

Grounding requirements: To ground the equipment prop-

erly, connect a Panduit Corporation UL listed Lug, P/N:

LCD8-10AL to the two threaded holes located on the rear of

each chassis and power supply module. All connections should

be made using 8AWG copper conductors.

Use Panduit Corporation, P/N: CT-940CH for crimping. (Each

Module must have its own grounding conductor.)

(GR-1089 requires treatment of ground connections and

painted surfaces as needed during installation.)

Installing the Hardware

4 Installing the Hardware June 2007

All surfaces that are used for intentionally grounding the EUT

shall be brought to a bright finish and an anti oxidant solution

must be applied to the surfaces being joined.

Non-conductive coatings (such as lacquer and enamel) must be

removed from threads and other contact surfaces to assure

electrical conductivity.

(Thread forming screws with paint piercing washers may be

used for this purpose during installation)

Warning. The intra-building interfaces of this platform,

including Gigabit Ethernet, are suitable for connection to

intra-building or unexposed wiring or cabling only with

shielded and grounded cables at both ends. The intra-building

ports of the equipment must not be metallically connected to

interfaces that connect to the OSP or its wiring.

Note. All bare conductors must be coated with an appro-

priate antioxidant compound before crimp connections are

made. All unplated connectors, braided strap, and bus bars

are to be brought to a bright finish and then coated with an

antioxidant before connecting them.

Weight Considerations

A single OS6850 weighs approximately 14 lbs

(6.24 Kgs). A stack of eight OS6850 switches weighs

approximately 112 lbs (50 Kgs).

June 2007 Installing the Hardware 5

Items Included

Your OmniSwitch 6850 Series switch order includes the

following items:

•OmniSwitch 6850 Series chassis

•Rack mount flanges with attachment screws (rack

mount flanges may be pre-installed on some orders)

•Power cord (country-specific)

•Documentation CD containing a complete set of user

guides for the switch and switch software. Refer to

“Related Documentation” on page 2 for a complete list of

included documentation.

Depending on the items ordered for your specific network

requirements, the following optional items may also be

included:

•Stacking cables (per order)

•SFPs (per order)

•10-Gigabit XFPs (per order)

•Backup power supply components and cables

(per order)

Unpacking and Initial Setup

Unpacking the Chassis

To protect your OmniSwitch chassis and hardware compo-

nents from electrostatic discharge (ESD) and physical damage,

read all unpacking recommendations and instructions care-

fully before beginning.

Recommendations

•Unpack your OmniSwitch chassis as close as possible

to the location where it will be installed.

•Depending on your order, Small Form-Factor Plugga-

bles (SFPs), stacking cables and backup power supply

components may be packaged separately. In order to

greatly reduce exposure to electrostatic discharge

(ESD) and physical damage, do not unpack these items

until they are ready to be installed.

Instructions

1Carefully cut the tape along the seam at the top of the

box containing the chassis.

2Lift the box’s top flaps. Remove any smaller boxes or

pouches that are enclosed and set them aside.

3Lift the chassis out of the packaging.

6 Installing the Hardware June 2007

4Carefully remove any foam pads and protective plastic

from the switch chassis.

Note. Alcatel-Lucent provides factory-installed blank

cover plates for empty backup power supply or 10-Giga-

bit expansion module bays. Do not remove these cover

plates unless a backup power supply or expansion module

is to be installed immediately at the corresponding bay.

5If you are installing multiple switches in a stacked

configuration, repeat steps 1 through 4 for the remaining

switches that will make up the stack.

6Once all OmniSwitch 6850 Series switches have been

removed from their packaging, continue to “Setting Up

the Switch.”

Setting Up the Switch

Note. Due to their airflow and access requirements,

OmniSwitch 6850 Series switches cannot be wall-

mounted.

Airflow Considerations

Be sure that your switch is placed in a well-ventilated, static-

free environment. Always allow adequate clearance at the

front, rear, and sides of the switch.

The following diagram shows recommended minimum clear-

ances for adequate chassis airflow and access to components at

the rear of the chassis:

OmniSwitch6850-48

USB

CLASS1LASER PRODUCT

1234

PRI PWR BPS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Rear. 5 inches minimum

at rear of chassis.

Front. 6 inches minimum

at front of chassis for

cable access and LED

visibility.

Sides. 2 inches minimum

at left and right sides for

chassis airflow.

Chassis Top View

Andere Handbücher für OmniSwitch 6850-48

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alcatel-Lucent Schalten Handbücher

Alcatel-Lucent

Alcatel-Lucent OmniStack LS 6224P Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7210 SAS E OS Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 1850 TSS-320 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 2220 Montageanleitung

Alcatel-Lucent

Alcatel-Lucent 1677 SONET Link Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 1850 TSS-320 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent LambdaUnite 1675 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent LambdaUnite 1675 Benutzerhandbuch

Alcatel-Lucent

Alcatel-Lucent 7210 SAS E OS Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 9900 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7210 SAS E OS Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent SFP Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 6850-48 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 6900 Installationshandbuch

Alcatel-Lucent

Alcatel-Lucent 7210 SAS D Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 9000 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 6250 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 1850 TSS-100 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7210 SAS E OS Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 1850 TSS-3 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 6250 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 1830 Benutzerhandbuch

Alcatel-Lucent

Alcatel-Lucent OmniSwitch 6450-P10S Installationshandbuch

Alcatel-Lucent

Alcatel-Lucent OmniStack 6200 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung