AlcoSense Precision + Bedienungsanleitung

User ManUal

INTRODUCTION

Thank you for purchasing the AlcoSense® Precision+

breathalyser.

The AlcoSense® Precision+ is certied to Australian Standard

AS3547 Type 2 Quantitative Device and is one of the world’s

most advanced hand-held alcohol detectors. It uses

electrochemical fuel cell sensor technology to ensure reliable

and accurate information as well as a convenient mode of

operation.

CONTENTS

DEVICE FEATURES

OPERATING INSTRUCTIONS

CONDITIONS FOR TESTING

WARRANTY DETAILS

TROUBLESHOOTING

DISCLAIMERS

SPECIFICATIONS

CALIBRATION AND SERVICE

PRODUCT REGISTRATION

.............................................3

..............................4

...............................5

...........................................6

..........................................7

......................................................8

...................................................8

..............................9

.................................9

DIAGRAM EXPLANATION

Mouthpiece holder

LCD Screen

On/Off button

Function button

USB Port (Not used)

Battery compartment cover

DEVICE FEATURES

NUMBER OF TESTS

When the unit rst starts up, it will display

the number of tests taken and the number

of tests remaining before calibration is

required.

PREPARATION

Gently pull down the battery compartment cover to remove it.

Insert fresh alkaline batteries (4 x AAA), checking that the + and

- on each battery are aligned according to the polarity diagram

inside. Carefully replace the battery compartment cover.

SWITCHING THE UNIT ON AND OFF

Press and hold the ON/OFF button for 2-3 seconds to switch

the unit on or off.

The unit will automatically switch off after 2 minutes of non-use.

OPERATING INSTRUCTIONS

NORMAL OPERATION

1. Insert a disposable mouthpiece through the unit.

2. Switch on the unit. When the screen reads BLOW, take a

deep breath and blow steadily into the mouthpiece for at

least 4 seconds.

3. Continue blowing until the beep stops. You will hear a

click.

4. Once complete, the unit displays the reading on the

screen.

• The next test can be performed by pressing the ON/OFF

button once, then repeating the previous steps. If the

reading from the previous test was higher than zero, please

wait 3 minutes before performing the next test to ensure

accurate results.

TEST RESULTS

0.000%

PASSIVE TEST

1. No mouthpieces are required for this operation.

2. When the screen reads BLOW, take a deep breath and

blow gently into the hole for 3 seconds. While blowing

press the ON/OFF button to record a breath sample.

Once complete, you will hear a click.

3. Once complete, the unit displays the reading on the screen

as No Alcohol or Alcohol Detected.

4. To conduct another test straight away, press the ON/OFF

button once and repeat previous steps.

5. If a more specic reading is required, use a mouthpiece

and test under normal operation.

PASSIVE TEST RESULT

CONDITIONS FOR TESTING

• Use a clean mouthpiece for each test.

• Do not allow samples containing smoke, tobacco or other

chemical products to enter the unit, as damage to the fuel

cell can occur.

• There must be an interval of at least 15 minutes after alcohol

consumption as alcohol residue in the mouth may give a false

reading.

• Such residue may also be left by aromatic drinks,

mouthwash, medicines and drops, as well as by belching

and vomiting. Rinsing your mouth with water or non-alcoholic

drinks does not substitute for an interval.

• A person’s blood alcohol concentration (BAC) can continue

to rise for up to 2 hours after drinking alcohol. If a caution

results or a result is close to the designated BAC, it is

recommended to wait and retest after 20 minutes. It can take

10 hours or more for a person’s BAC to return to zero after a

high BAC has been reached.

• A further test should be carried out later in the day or the

following morning.

• Working temperature range: 5°C to 40°C.

Storage temperature: -15°C to 65°C.

LIABILITY FOR PROPER FUNCTION OR DAMAGE

The liability for proper functioning of the instrument is

irrevocably transferred to the owner or operator in the

event the instrument is serviced or repaired by personnel

not employed or authorised by Andatech. In such an

event, the warranty will be void.

WARRANTY DETAILS

It is our aim to provide you with quality products that you

can trust. Our products come with guarantees that cannot

be excluded under the Australian Consumer Law. You are

entitled to a replacement or a refund for a major failure and

for compensation for any other reasonably foreseeable loss

or damage.

You are also entitled to have the goods repaired or

replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure.

The Guarantee

The product is guaranteed to be free from defects in

workmanship and parts for a period of 1 year from the date

of purchase. Defects that occur within this warranty period,

under normal use and care, will be repaired, replaced or

refunded at our discretion, solely at our option with no

charge for parts and labour. The beneﬁts conferred by

this warranty are in addition to all rights and remedies in

respect of the product that the consumer has under the

Trade Practices Act and similar state laws.

Proof of Purchase

This warranty is valid for the original purchase and is not

transferable. Please keep your purchase docket or receipt as

proof of purchase and as proof of date on which the purchase

was made. The purchase docket (or a copy) or receipt must be

presented with the warranty when making a claim under this

warranty.

Service during the Warranty Period

To claim for warranty, contact us on 1300 800 200 or info@

andatech.com.au to get an RA# (Return Authorisation Number).

Ensure that the RA# is clearly stated on the outside of the

packaging and that the product is properly packaged so that

no damage occurs to the product during transit. Shipping

of the product back to us for warranty will be at your cost. A

product return without the RA# or proof of purchase will not be

accepted.

Extent of Warranty

This warranty is limited to defects in workmanship or parts. All

defective products or parts will be repaired or replaced. This

warranty does not cover manuals and packaging.

TROUBLESHOOTING

ERROR "PLEASE BLOW HARDER"

Breath sample was not long, hard, or steady enough, or you

did not wait for the beep to end before you stopped blowing.

Blow a long, slow and steady breath. Don't stop blowing until

the beep ends.

'CALIBRATION NEEDED' WARNING

The unit has passed its calibration due date or has exceeded

the number of allowed tests. You can press any button to

continue using the unit, however we strongly recommend that

you send it back to us for calibration.

BATTERY LIFE TOO SHORT

Use only alkaline batteries, or if using rechargeable batteries,

use either NiMH or rechargheable alkaline batteries.

Normal Wear and Tear

This warranty does not cover normal wear and tear to

the product or parts.

Exclusions

This warranty does not cover:

• Calibration costs.

• Any defect caused by an accident, misuse, abuse,

improper operation, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

the distributor.

• Any product that has been damaged by a lightning

strike either directly or indirectly or a main power

surge or liquid ingress.

• The product if it is located outside of

Australia.

• Any damage caused by improper

power input or improper

cable connection.

DISCLAIMERS

This product must be used strictly in accordance with

the instructions in this manual. This product is intended

to provide the user with an indication of alcohol on the

breath. However, neither the manufacturer nor the supplier

gives any warranty (express or implied) that the product

can give any indication of blood alcohol level. A person's

BAC (Blood Alcohol Concentration) can only be accurately

measured by the administration of a blood test.

This product only measures breath alcohol content which,

in turn, only gives an approximate indication of blood

alcohol concentration. In these circumstances the user of

this product should not rely on the information provided

thereby as an accurate indication of their blood alcohol

concentration or of their level of intoxication or of their

tness to drive and in particular should not take any action

in reliance on such information as the product can provide

no more than an indication of alcohol on the breath.

If the user of this product makes any decision or takes

any action based on the use of the product such decision

or such action shall be at the sole risk of the user and

neither the manufacturer nor the supplier assumes any

responsibility for such decision or action. In particular,

neither the manufacturer nor the supplier shall be in

any way liable if the user of the product asserts that the

product led them to believe that they were t to operate a

motor vehicle and are subsequently found not to be so t.

SPECIFICATIONS

Indication of %BAC 0.000 - 0.500%BAC

Accuracy ±0.005%BAC at 0.100%BAC

Warm Up Time Within 3 seconds

Response Time Within 3 seconds

Recycle Time 5 seconds

Power Supply 4 x AAA Alkaline Batteries

Working Temperature -5 – 40°C

Calibration Frequency Manufacturer recommended:

Every 1000 tests or 6 months,

whichever comes rst.

Product Weight 150g including batteries

Product Dimensions 140mm (h) x 55mm (w) x 30mm (d)

PRODUCT REGISTRATION

Visit my.andatech.com.au to register your warranty online and

receive calibration reminders. Alternatively, complete this form

and forward to the address below with a copy of your proof of

purchase.

Andatech Corporation Pty Ltd

PO BOX 3038, Nunawading VIC 3131 Australia.

Product AlcoSense® Precision+

Date of purchase

Place of purchase

Surname

Given name

Address

Suburb

Postcode State

Contact no.

CALIBRATION AND SERVICE

Andatech recommends the AlcoSense® Precision+ to

be calibrated every 6 months or after 1000 uses.

PRODUCT REGISTRATION

my.andatech.com.au is a central location where you

can register your warranty, sign up to recieve calibration

reminders and book in calibrations. Once you have

registered, you can add as many AlcoSense products as

needed to that account.

Andatech Corporation Pty Ltd

PO Box 3038

Nunawading VIC 3131

1300 800 200

www.andatech.com.au

Version 2.0. Updated 04.06.2014

CALIBRATION CENTRE

Inhaltsverzeichnis

Andere AlcoSense Prüfgeräte Handbücher

AlcoSense

AlcoSense PRODIGY Bedienungsanleitung

AlcoSense

AlcoSense Lite Bedienungsanleitung

AlcoSense

AlcoSense ZENITH+ Bedienungsanleitung

AlcoSense

AlcoSense Excel Bedienungsanleitung

AlcoSense

AlcoSense Checkmate Bedienungsanleitung

AlcoSense

AlcoSense Elite2 Bedienungsanleitung

AlcoSense

AlcoSense Zero Bedienungsanleitung

AlcoSense

AlcoSense STEALTH Bedienungsanleitung

AlcoSense

AlcoSense Ultra Bedienungsanleitung

AlcoSense

AlcoSense Lite 2 Bedienungsanleitung

AlcoSense

AlcoSense ELITE Bedienungsanleitung

AlcoSense

AlcoSense Verity Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung