Alderon Industries Versa'larm 4X Bedienungsanleitung

Alarm Systems Control Panels Float Switches Leak Detection Systems Page 1 of 2

PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com

Operation, Maintenance and Installation Manual

Versa’larm 4X

Outdoor Alarm System

P/N: 10045 Rev. B

Before proceeding with the installation or operation of the Versa’larm™ 4X, read all

instructions thoroughly, as well as complying with all Federal, State and Local Codes,

Regulations and Practices. The Versa’larm 4X must be installed by qualified personnel

familiar with all applicable local electrical and mechanical codes. Refer to the National

Electrical Code (NFPA 70). Failure to properly install and test this product can result in

personal injury or equipment malfunction.

The Versa’larm 4X is a multipurpose alarm that can be used in a wide variety of applica-

tions such as: septic tanks, sumps, holding tanks, pump chambers and water tanks.

Introduction

Safety Guidelines

1. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE,

ETC. DO NOT USE IN EXPLOSIVE ATMOSPHERES.

2. DICONNECT ALL POWER WHEN INSTALLING, WORKING ON THE UNIT OR REPLACING THE FUSE.

3. FAILURE TO TURN OFF ALL POWER WHEN SERVICING THE VERSA’LARM 4X COULD RESULT IN

SERIOUS INJURY OR DEATH.

Description of Operation

The Versa’larm 4X is powered by 120 VAC, “hard wired”. When power is applied, the green “Power” indicator

light (located externally) will illuminate. When a float switch “closes” the buzzer and beacon will turn “on”.

Pressing the “Silence” button deactivates the buzzer and the optional auxiliary contacts. When the alarm is

remedied, the system automatically resests itself. The system can be tested be pressing the “Test” switch, when

pressing the switch, the buzzer should annunciate and the beacon should illuminate. The auxiliary contacts are

activated when an alarm condition occurs. The single pole double throw contacts can switch a maximum of 5

amps at 120 VAC.

Electrical Information

Primary Power: 120 VAC, 50/60 Hz

Watts: 10 Watts

Fuse: 1 Amp Fast Acting Type AGC

Auxiliary Contacts: Single Pole, Double Throw

5 Amps at 120 VAC

Buzzer: 85db at 10 Feet

Switch: UL Listed, 120 VAC, 1 Amp Minimum

(signaling device) Single Pole, Single Throw

Alarm Systems Control Panels Float Switches Leak Detection Systems Page 2 of 2

PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com

Operation, Maintenance and Installation Manual

Versa’larm 4X

Outdoor Alarm System

P/N: 10045 Rev. B

Installation of the Versa’larm 4X

1. Determine mounting location for the Versa’larm 4X. Mount the unit using four #8 x 1.25” self tapping screws (not included)

(Fig. 1). The cover must be removed, then install the screws through the hole openings provided in the enclosure. Note: The

cover seals around the hole openings maintain a waterproof enclosure.

2. Drill holes for conduit connections, see Figure 1 for recommended hole locations on the enclosure. Attach conduit per

National Electrical Code.

3. Bring power wires through the conduit into the unit and connect to the terminal block (Fig. 2). Connect L1 to TB1, N to TB2

and G to TB3. Make sure the power is on a separate circuit breaker from any other device to maintain power integrity.

4. Bring “signaling device” wires (such as a float or pressure switch, etc.) through the conduit and connect to the terminal

block (Fig. 2). Connect to TB4 and TB5. Caution! - When installing the “signaling device”, refer to its installation instructions

for proper installation. Connect only with UL or CSA listed switches rated 1 amp at 120 VAC minimum.

5. Caution! - When installing wires, route all wires away from sharp objects and internal components. After all wires are

installed, seal all conduits, per National Electrical Code, that come from sources containing corrosive gases. Failure to do so

will cause premature failure and void warranty.

6. If using the auxiliary contacts, make connection via wire nuts (Fig. 3). The auxiliary contacts can switch a maximum of 5

amps, 120 VAC.

7. Reinstall the enclosure cover and carefully tighten the four screws.

Testing the Versa’larm 4X

1. Turn on power, the “Power” indicator light should illuminate. Then, press the “Test” button located on the left side of the unit

(Fig. 1). Once the “Test” button is pressed, the buzzer should annunciate and beacon should illuminate. While pressing the

“Test” button, press the “Silence” button and the buzzer should silence. Let go of the “Test” button and repeat the sequence

several times to ensure the system is working properly.

2. Test the system similar to Step 1, but by activating the “signaling device”. The buzzer should annunicate and the beacon

should illuminate.

3. Test product weekly to ensure system integrity.

(Fig. 3)

(white)

(red)

(black)

CR2 CR2

COMMON NORMALLY

CLOSED

NORMALLY

OPEN

Auxiliary Contacts

5 Amps, 120 VAC Maximum

(Fig. 1)

Mounting Holes (2)

Test

Button

Silence

Button

Power

Indicator Light

Buzzer

Beacon

Recommended

Conduit Hole

Locations

(Fig. 2)

Do not exceed 8 in. lbs. torque when

tightening screw terminals.

Wire Range: 12-24 AWG

L1 NG

Signaling

Device

(Float Switch)

(120 VAC 50/60 Hz)

Terminal Block (TB) 1 2 3 4 5

CAUTION! - Failure to connect

power in and float as shown

(Fig. 2) will cause catastrophic

circuit board damage.

Inhaltsverzeichnis

Andere Alderon Industries Sicherheitssystem Handbücher

Alderon Industries

Alderon Industries Power Post VA-02 Bedienungsanleitung

Alderon Industries

Alderon Industries Vizzyalarm VZW-02 Bedienungsanleitung

Alderon Industries

Alderon Industries 7001 Versa’larm Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-00005 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-0001 Bedienungsanleitung

Alderon Industries

Alderon Industries Versa'larm VA01D Bedienungsanleitung

Alderon Industries

Alderon Industries Versa'larm VA02A Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O Bedienungsanleitung

Alderon Industries

Alderon Industries Vizzyalarm VZW-01 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm 4X Bedienungsanleitung

Alderon Industries

Alderon Industries Wireless Versa'larm VA01B Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-0001 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm VLIO-0004 Bedienungsanleitung

Alderon Industries

Alderon Industries Oil Alert VA03 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-0002 Bedienungsanleitung

Alderon Industries

Alderon Industries Versa'larm VA01A Bedienungsanleitung

Alderon Industries

Alderon Industries Versa'larm VA01A Bedienungsanleitung

Alderon Industries

Alderon Industries Sump Advisor 2000514 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-00005 Bedienungsanleitung

Alderon Industries

Alderon Industries Sump Advisor 2000514 Bedienungsanleitung

Alderon Industries

Alderon Industries Versa'larm VA02B Bedienungsanleitung

Alderon Industries

Alderon Industries Oil Alert VA02 Bedienungsanleitung

Alderon Industries

Alderon Industries VersAlarm 4X Bedienungsanleitung

Alderon Industries

Alderon Industries 8059 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung