Alinco DR-135 Bedienungsanleitung

Andere Handbücher für DR-135

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alinco Autoempfänger Handbücher

Alinco

Alinco DR-M03SX Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

DR-135 / DR-235 / DR-435

Service Manual

CONTENTS

SPECIFICATIONS

GENERAL ........................................................................................ 2

TRANSMITTER ................................................................................ 2

RECEIVER ....................................................................................... 2

CIRCUIT DESCRIPTION DR-135

1) Receiver System (DR-135) ........................................................... 3, 4

2) Transmitter System (DR-135) ....................................................... 4, 5

3) PLL Synthesizer Circuit (DR-135) ................................................. 5, 6

4) Receiver System (DR-235) ........................................................... 6, 7

5) Transmitter System (DR-235) ....................................................... 7, 8

6) PLL Synthesizer Circuit (DR-235) ................................................. 8, 9

7) Receiver System (DR-435) ......................................................... 9, 10

8) Transmitter System (DR-435) ......................................................... 10

9) PLL Synthesizer Circuit (DR-435) ................................................... 11

10) CPU and Peripheral Circuits(DR-135 DR-235 DR-435) ............. 11,12

11) Power Supply Circuit ....................................................................... 13

12) M3826M8269GP (XA0818) ....................................................... 14~16

SEMICONDUCTOR DATA

1) M5218FP (XA0068) ........................................................................ 17

2) NJM7808FA (XA0102) .................................................................... 17

3) TC4S66F (XA0115) ........................................................................ 17

4) TK10930VTL (XA0223) .................................................................. 18

5) BU4052BF (XA0236) ...................................................................... 19

6) TC4W53FU (XA0348) .................................................................... 19

7) M64076GP (XA0352) ..................................................................... 20

8) LA4425A (XA0410) ......................................................................... 21

9) M67746 (XA0412) .......................................................................... 21

10) M68729 (XA0591) .......................................................................... 22

11) M57788 (XA0077A) ........................................................................ 23

12) mPC2710T (XA0449) ..................................................................... 24

13) NJM2902 (XA0596) ........................................................................ 24

14) 24LC32A (XA0604) ........................................................................ 25

15) S-80845ALMP-EA9-T2 (XA0620) ................................................... 25

16) L88MS05TLL (XA0675) .................................................................. 25

17) AN8010M (XA0119) ....................................................................... 26

18) TK10489M (XA0314) ...................................................................... 26

19) Transistor, Diode, and LED Ontline Drawings .................................. 27

20) LCD Connection (TTR3626UPFDHN) ........................................... 28

EXPLODED VIEW

1) Top and Front View ......................................................................... 29

2) Bottom View .................................................................................... 30

3) LCD Assembly ................................................................................ 31

PARTS LIST

CPU .......................................................................................... 32, 33

Main Unit(DR-135) .................................................................... 33~36

Main Unit(DR-235) .................................................................... 36~39

VCO Unit(DR-235) ......................................................................... 39

Main Unit(DR-435) .......................................................................... 42

VCO Unit(DR-435) ......................................................................... 42

Mechanical Parts ............................................................................ 43

Packing Parts ................................................................................. 43

ACCESSORIES .............................................................................. 43

ACCESSORIES(SCREW SET) ...................................................... 43

TNC(EJ41U) .................................................................................. 44

TNC (EJ41U) Packing Parts ........................................................... 45

DR-135 ADJUSTMENT

1) Adjustment Spot ............................................................................ 46

2) VCO and RX Adjustment Specification ........................................... 47

3) Tx Adjustment Specification ............................................................ 47

4) Rx Test Specification ....................................................................... 48

5) Tx Test Specification ....................................................................... 49

DR-235 ADJUSTMENT

1) Adjustment Spot ............................................................................ 50

2) VCO and RX Adjustment Specification ........................................... 51

3) Tx Adjustment Specification ............................................................ 51

4) Rx Test Specification ....................................................................... 52

5) Tx Test Specification ....................................................................... 53

DR-435 ADJUSTMENT

1) Adjustment Spot ............................................................................ 54

2) VCO and RX Adjustment Specification ........................................... 55

3) Tx Adjustment Specification ............................................................ 55

4) Rx Test Specification ....................................................................... 56

5) Tx Test Specification ....................................................................... 57

PC BOARD VIEW

1) CPU Unit Side A ............................................................................. 58

2) CPU Unit Side B ............................................................................. 58

3) Main Unit Side A DR-135 (UP 0400B) ............................................. 59

4) Main Unit Side B DR-135 (UP 0400B) ............................................. 59

5) Main Unit Side A DR-235 (UP 0414) ............................................... 60

6) Main Unit Side B DR-235 (UP 0414) ............................................... 60

7) Main Unit Side A DR-435 (UP 0415) ............................................... 61

8) Main Unit Side B DR-435 (UP 0415) ............................................... 61

9) Tnc Unit Side A (UP 0402) (DR-135TP only) .................................. 62

10) Tnc Unit Side B (UP 0402) (DR-135TP only) .................................. 62

SCHEMATIC DIAGRAM

1) CPU Unit DR-135 / DR-235 / DR-435 ............................................. 63

2) Main Unit DR-135 ........................................................................... 64

3) Main Unit DR-235 ........................................................................... 65

4) Main Unit DR-435 ........................................................................... 66

5) TNC Unit (DR-135TP only) ............................................................. 67

BLOCK DIAGRAM

1) DR-135 ........................................................................................... 68

2) DR-235 ........................................................................................... 69

3) DR-435 ........................................................................................... 70

ALINCO,INC.

All manuals and user guides at all-guides.com

all-guides.com

SPECIFICATIONS

General

Frequency coverage DR-135 DR-235 DR-435

118.000 ~ 135.995MHz (AM RX) 216.000 ~ 279.995MHz (RX) 350.000 ~ 511.995MHz (RX)

136.000 ~ 173.995MHz (RX) 222.000 ~ 224.995MHz (TX) 430.000 ~ 449.995MHz (TX)

144.000 ~ 147.995MHz (TX)

144.000 ~ 145.995MHz (RX.TX) 430.000 ~ 439.995MHz (RX.TX)

TA,TAG 118.000 ~ 135.995MHz (AM RX)

(Commercial) 136.000 ~ 173.995MHz (RX.TX)

Operating mode

Frequency resolution

Number of memory

channels

Antenna impedance

Power requirement

Ground method

Current drain Receive 0.6A(Max.) 0.4A(Squelched)

Transmit 11.0A max. 8.0A max. 10.0A max.

Operating temperature

Frequency stability

Dimensions

Weight

Transmitter

Output power High:50W (144-148MHz) High:25W High:35W

More than 33W (136-174MHz)

Mid:10W Mid:10W Mid:10W

Low:Approx.5W Low:Approx.5W Low:Approx.5W

Modulation system

Maximum frequency

deviation

Spurious emission

Adjacent

channel power

Noise and hum ratio

Receiver

Sensitivity

Receiver circuitry

Intermediate

frequency

Squelch sensitivity

Adjacent channel

selectivity

Intermoduration

rejection ratio

Spurious and

image rejection ratio

Audio output power

! Note: All specifications are subject to change without notice or obligation.

2.0W (8 ,10%THD)

70dB

60dB

-65dB(Wide mode) -55dB(Narrow mode)

-18dBu

Double conversion superheterodyne

-16dBu for 12dB SINAD

-40dB (Wide mode) -34dB (Narrow mode)

-60dB

±5kHz (Wide mode) ±2.5kHz (Narrow mode)

Variable reactance frequency modulation

142(w)×40(h)×174(d) mm

( 142×40×188mm for projection included)

Approx. 1.0kg

E,EG

(European amateur)

T,TG

(U.S amateur)

- 10 to 60

±5ppm

FM 16K0F3E (Wide mode) 8K50F3E (Narrow mode)

5,8.33,10,12.5,15,20,25,30,50 KHz

100

50 unbalanced

13.8V DC ±15% (11.7 to 15.8V)

Negative ground

˚C ˚C

Microphone impedance

1st 21.7MHz 2nd 450kHz 1st 30.85MHz 2nd 455kHz 1st 30.85MHz 2nd 455kHz

All manuals and user guides at all-guides.com

CIRCUIT DESCRIPTION DR-135/DR-235/DR-435

1) Receiver System (DR-135)

The receiver system is a double superheterodyne system with a 21.7 MHz first IF and a 450 kHz second IF.

1. Front End

The received signal at any frequency in the 136.000MHz to 173.995MHz range

is passed through the low-pass filter (L116, L115, L114, L113, C204, C203,

C202, C216 and C215) and tuning circuit (L105, L104 and D105, D104), and

amplified by the RF amplifier (Q107). The signal from Q107 is then passed

through the tuning circuit (L103, L102, and varicaps D103 and D102) and

converted into 21.7 MHz by the mixer (Q106). The tuning circuit, which

consists of L105, L104, varicaps D105 and D104, L103, L102, varicaps

D103 and D102, is controlled by the tracking voltage form the VCO.The local signal

from the VCO is passed through the buffer (IC112), and supplied to the source of

the mixer (Q106).The radio uses the lower side of the superheterodyne system.

2. IF Circuit

The mixer mixes the received signal with the local signal to obtain the sum of

and difference between them. The crystal filter (XF102, XF101) selects 21.7

MHz frequency from the results and eliminates the signals of the unwanted

frequencies.The first IF amplifier (Q105) then amplifies the signal of the selected

frequency.

3. Demodulator Circuit

After the signal is amplified by the first IF amplifier (Q105), it is input to pin 24 of

the demodulator IC (IC108). The second local signal of 21.25 MHz (shared

with PLL IC reference oscillation), which is oscillated by the internal oscillation

circuit in IC116 and crystal (X103), is input through pin 1 of IC108.Then, these

two signals are mixed by the internal mixer in IC108 and the result is converted

into the second IF signal with a frequency of 450 kHz.The second IF signal is

output from pin 3 of IC108 to the ceramic filter (FL101 or FL102), where the

unwanted frequency band of that signal is eliminated, and the resulting signal

is sent back to the IC108 through pins 5.

The second IF signal input via pin 5 is demodulated by the internal limiter

amplifier and quadrature detection circuit in IC108, and output as an audio

signal through pin 12.

4. Audio Circuit

The audio signal from pin 12 of IC108 is amplified by the audio amplifier

(IC104:A),and switched by the signal switch IC (IC111) and then input it to the

de-emphasis circuit.

and is compensated to the audio frequency characteristics in the de-emphasis

circuit (R203, R207, R213, R209, C191, C218, C217) and amplified by the AF

amplifier (IC104:D).The signal is then input to volume (VR1) .The adjusted signal is

sent to the audio power amplifier (IC117) through pin 1 to drive the speaker.

All manuals and user guides at all-guides.com

5. Squelch Circuit

The detected output which is outputted from the pin 12 of IC108 is inputted to

pin 19 of IC108 after it was been amplified by IC104:A and it is outputted from

pin 20 after the noise component was been eliminated from the composed

band pass filter in the built in amplifier of the IC, then the signal is rectified by

D106 to convert into DC component. The adjusted voltage level at VR101 is

delivered to the comparator of the CPU.

The voltage is led to pin 2 of CPU and compared with the setting voltage. The

squelch will open if the input voltage is lower than the setting voltage.

During open squelch, pin 30 (SQC) of the CPU becomes "L" level, AF control

signal is being controlled and sounds is outputted from the speaker.)

6. AIR Band Reception(T only)

When the frequency is within 118~135.995MHz, Q110 automatically turns ON,

pin 14 of IC108 becomes "L" level and the condition becomes in AM detection

mode.

The receiver signal passed through the duplexer is let to the antenna switch

(D107,D101).After passing through the band-pass filter, the signal is amplified

by RF amplifier Q112. Secondly the signal is mixed with the signal from the first

local oscillator in the first-mixer Q106,then converted into the first IF. Its unwanted

signal is let to IC106, pin24.Then converted into the second IF.and is demodulated

by AM decoder of IC106, and is output from pin13 as the AF signal.

7. WIDE/NARROW switching circuit

The 2nd IF 450 kHz signal which passes through filter FL101 (wide) and FL102

(narrow) during narrow, changes its width using the width control switching

IC103 and IC102.

2) Transmitter System (DR-135)

1. Modulator Circuit

The audio signal is converted to an electrical signal by the microphone, and

input it to the microphone amplifier (Q6). Amplified signal which passes through

mic-mute control IC109 is adjusted to an appropriate mic-volume by means of

mic-gain adjust VR106.

IC114:A and B consists of two operational amplifiers; one amplifier (pins 1, 2,

and 3) is composed of pre-emphasis and IDC circuits and the other (pins 5, 6,

and 7) is composed of a splatter filter. The maximum frequency deviation is

obtained by VR107. and input to the signal switch (IC113) (9600 bps packet

signal input switch) and input to the cathode of the varicap of the VCO, to

change the electric capacity in the oscillation circuit.This produces the frequency

modulation.

All manuals and user guides at all-guides.com

2. Power Amplifier Circuit

The transmitted signal is oscillated by the VCO, amplified by the drive amplifier

(IC112) and younger amplifier (Q115), and input to the final power module

(IC110).The signal is then amplified by the final power module (IC110) and led

to the antenna switch (D110) and low-pass filter (L113, L114, L115, L116,

C215, C216, C202, C203 and C204), where unwanted high harmonic waves

are reduced as needed, and the resulting signal is supplied to the antenna.

3. APC Circuit

Part of the transmission power from the low-pass filter is detected by D111 and

D112, converted to DC.The detection voltage is passed through the APC circuit

(Q118, Q117, Q116), then it controls the APC voltage supplied to the younger

amplifier Q115 and the final power module IC110 to fix the transmission power.

3) PLL Synthesizer Circuit (DR-135)

1. PLL

The dividing ratio is obtained by sending data from the CPU (IC1) to pin 2 and

sending clock pulses to pin 3 of the PLL IC (IC116).The oscillated signal from

the VCO is amplified by the buffer (Q134 and Q135) and input to pin 15 of

IC116. Each programmable divider in IC116 divides the frequency of the input

signal by N according to the frequency data, to generate a comparison frequency of

5 or 6.25 kHz.

2. Reference Frequency Circuit

The reference frequency appropriate for the channel steps is obtained by dividing

the 21.25 MHz reference oscillation (X103) by 4250 or 3400, according to the data

from the CPU (IC1).When the resulting frequency is 5 kHz, channel steps of 5,

10, 15, 20, 25, 30, and 50 kHz are used. When it is 6.25 kHz, the 12.5 kHz

channel step is used.

3. Phase Comparator Circuit

The PLL (IC116) uses the reference frequency, 5 or 6.25kHz. The phase

comparator in the IC116 compares the phase of the frequency from the VCO

with that of the comparison frequency, 5 or 6.25kHz, which is obtained by the

internal divider in IC116.

4. PLL Loop Filter Circuit

If a phase difference is found in the phase comparison between the reference

frequency andVCO output frequency, the charge pump output (pin 13) of IC116

generates a pulse signal, which is converted to DC voltage by the PLL loop

filter and input to the varicap of the VCO unit for oscillation frequency control.

All manuals and user guides at all-guides.com

5. VCO Circuit

A Colpitts oscillation circuit driven by Q131 directly oscillates the desired frequency.

The frequency control voltage determined in the CPU (IC1) and PLL circuit is

input to the varicaps (D122 and D123). This change the oscillation frequency,

which is amplified by the VCO buffer (Q134) and output from the VCO area.

6. VCO Shift Circuit

During transmission or the AIR band Reception (118~136 MHz), the VCO shift

circuit turns ON Q138, change control the capacitance of L123 and safely

oscillates the VCO by means of H signal from pin 16 of IC116.)

4) Receiver System (DR-235)

The receiver system is a double superheterodyne system with a 30.85 MHz first IF and a 455 kHz second IF.

1. Front End

The received signal at any frequency in the 216.000MHz to 279.995MHz range

is passed through the low-pass filter (L116, L115, L114, L113, C204, C203,

C202, C216 and C215) and tuning circuit (L105, L104 and D105, D104), and

amplified by the RF amplifier (Q107). The signal from Q107 is then passed

through the tuning circuit (L103, L107, L102, and varicaps D103, D107 and

D102) and converted into 30.85 MHz by the mixer (Q106). The tuning circuit,

which consists of L105, L104, varicaps D105 and D104, L103, L107, L102,

varicaps D103, D107 and D102, is controlled by the tracking voltage form the

VCO.The local signal from the VCO is passed through the buffer (Q112), and

supplied to the source of the mixer (Q106).The radio uses the lower side of the

superheterodyne system.

2. IF Circuit

The mixer mixes the received signal with the local signal to obtain the sum of

and difference between them.The crystal filter (XF102, XF101) selects 30.85

MHz frequency from the results and eliminates the signals of the unwanted

frequencies.The first IF amplifier (Q105) then amplifies the signal of the selected

frequency.

3. Demodulator Circuit

After the signal is amplified by the first IF amplifier (Q105), it is input to pin 24 of

the demodulator IC (IC108). The second local signal of 30.395 MHz, which is

oscillated by the internal oscillation circuit in IC108 and crystal (X104), is input

through pin 1 of IC108.Then, these two signals are mixed by the internal mixer

in IC108 and the result is converted into the second IF signal with a frequency

of 455 kHz.The second IF signal is output from pin 3 of IC108 to the ceramic

filter (FL101 or FL102), where the unwanted frequency band of that signal is

eliminated, and the resulting signal is sent back to the IC108 through pins 5.

The second IF signal input via pin 5 is demodulated by the internal limiter

amplifier and quadrature detection circuit in IC108, and output as an audio

signal through pin 12.

All manuals and user guides at all-guides.com

all-guides.com

4. Audio Circuit

The audio signal from pin 12 of IC108 is amplified by the audio amplifier

(IC104:A), and switched by the signal switch IC (IC111) and then input it to the

de-emphasis circuit.

and is compensated to the audio frequency characteristics in the de-emphasis

circuit (R203, R207, R213, R209, C191, C218, C217) and amplified by the AF

amplifier (IC104:D). The signal is then input to volume (VR1) . The adjusted

signal is sent to the audio power amplifier (IC117) through pin 1 to drive the

speaker.

5. Squelch Circuit

The detected output which is outputted from the pin 12 of IC108 is inputted to

pin 19 of IC108 after it was been amplified by IC104:A and it is outputted from

pin 20 after the noise component was been eliminated from the composed

band pass filter in the built in amplifier of the IC, then the signal is rectified by

D106 to convert into DC component. The adjusted voltage level at VR101 is

delivered to the comparator of the CPU.

The voltage is led to pin 2 of CPU and compared with the setting voltage. The

squelch will open if the input voltage is lower than the setting voltage.

During open squelch, pin 30 (SQC) of the CPU becomes "L" level, AF control

signal is being controlled and sounds is outputted from the speaker.)

6. AIR Band Reception(T only)

If it is made air band receiving mode, IF signal is demodulated by AM decoder

of IC106, and is output from pin13 as the AF signal.

7. WIDE/NARROW switching circuit

The 2nd IF 455 kHz signal which passes through filter FL101 (wide) and FL102

(narrow) during narrow, changes its width using the width control switching

IC103 and IC102.

5) Transmitter System (DR-235)

1. Modulator Circuit

The audio signal is converted to an electrical signal by the microphone, and

input it to the microphone amplifier (Q6). Amplified signal which passes through

mic-mute control IC109 is adjusted to an appropriate mic-volume by means of

mic-gain adjust VR106.

IC114:A and B consists of two operational amplifiers; one amplifier (pins 1, 2,

and 3) is composed of pre-emphasis and IDC circuits and the other (pins 5, 6,

and 7) is composed of a splatter filter. The maximum frequency deviation is

obtained by VR107. and input to the signal switch (IC113) (9600 bps packet

signal input switch) and input to the cathode of the varicap of the VCO, to

change the electric capacity in the oscillation circuit.This produces the frequency

modulation.

All manuals and user guides at all-guides.com

2. Power Amplifier Circuit

The transmitted signal is oscillated by the VCO, amplified by the drive amplifier

(IC112) and younger amplifier (Q115), and input to the final power module

(IC110).The signal is then amplified by the final power module (IC110) and led

to the antenna switch (D110) and low-pass filter (L113, L114, L115, L116,

C215, C216, C202, C203 and C204), where unwanted high harmonic waves

are reduced as needed, and the resulting signal is supplied to the antenna.

3. APC Circuit

Part of the transmission power from the low-pass filter is detected by D111

and D112, converted to DC. The detection voltage is passed through the

APC circuit (Q118, Q117, Q116), then it controls the APC voltage supplied to

the younger amplifier Q115 and the final power module IC110 to fix the

transmission power.

6) PLL Synthesizer Circuit (DR-235)

1. PLL

The dividing ratio is obtained by sending data from the CPU (IC1) to pin 2 and

sending clock pulses to pin 3 of the PLL IC (IC501).The oscillated signal from

the VCO is amplified by the buffer (Q504 and Q501) and input to pin 15 of

IC501. Each programmable divider in IC501 divides the frequency of the input

signal by Naccording to the frequency data, to generate a comparison frequency of

5 or 6.25 kHz.

2. Reference Frequency Circuit

The reference frequency appropriate for the channel steps is obtained by

dividing the 12.8 MHz reference oscillation (X103) by 2560 or 2048, according

to the data from the CPU (IC1).When the resulting frequency is 5 kHz, channel

steps of 5, 10, 15, 20, 25, 30, and 50 kHz are used. When it is 6.25 kHz, the

12.5 kHz channel step is used.

3. Phase Comparator Circuit

The PLL (IC501) uses the reference frequency, 5 or 6.25kHz. The phase

comparator in the IC501 compares the phase of the frequency from the VCO

with that of the comparison frequency, 5 or 6.25kHz, which is obtained by the

internal divider in IC501.

4. PLL Loop Filter Circuit

If a phase difference is found in the phase comparison between the reference

frequency andVCO output frequency, the charge pump output (pin 13) of IC501

generates a pulse signal, which is converted to DC voltage by the PLL loop

filter and input to the varicap of the VCO unit for oscillation frequency control.

All manuals and user guides at all-guides.com

5. VCO Circuit

A Colpitts oscillation circuit driven by Q503 directly oscillates the desired frequency.

The frequency control voltage determined in the CPU (IC1) and PLL circuit is

input to the varicaps (D503 and D504). This change the oscillation frequency,

which is amplified by the VCO buffer (Q504) and output from the VCO area.

7) Receiver System (DR-435)

The receiver system is a double superheterodyne system with a 30.85 MHz first IF and a 455 kHz second IF.

1. Front End

The received signal at any frequency in the 430.00MHz to 439.995MHz range

is passed through the low-pass filter (L115, L114, L116, C204, C203, C202,

C216 and C215) and amplified by the RF amplifier (Q107). The signal from

Q107 is then passed through the BPF circuit (L103, L102) and converted into

30.85 MHz by the mixer (Q106). The local signal from the VCO is passed

through the buffer (Q503,Q504), and supplied to the source of the mixer (Q106).

The radio uses the lower side of the superheterodyne system.

2. IF Circuit

The mixer mixes the received signal with the local signal to obtain the sum of

and difference between them.The crystal filter (XF101) selects 30.85MHz frequency

from the results and eliminates the signals of the unwanted frequencies. The first IF

amplifier (Q105) then amplifies the signal of the selected frequency.

3. Demodulator Circuit

After the signal is amplified by the first IF amplifier (Q105), it is input to pin 20 of

the demodulator IC (IC108). The second local signal of 30.85MHz (Crystal

oscillator) is input pin 1 of IC108. Then, these two signals are mixed by the

internal mixer in IC108 and the result is converted into the second IF signal

with a frequency of 455 kHz.The second IF signal is output from pin 4 of IC108

to the ceramic filter (FL101 or FL102), where the unwanted frequency band of

that signal is eliminated, and the resulting signal is sent back to the IC108

through pins 6.

The second IF signal input via pin 6 is demodulated by the internal limiter

amplifier and quadrature detection circuit in IC108, and output as an audio

signal through pin 11.

4. Audio Circuit

The audio signal from pin 11 of IC108 is amplified by the audio amplifier

(IC104:A), and switched by the signal switch IC (IC111) and then input it to the

de-emphasis circuit.

and is compensated to the audio frequency characteristics in the de-emphasis

circuit (R203, R207, R213, R209, C191, C218, C217) and amplified by the AF

amplifier (IC104:D). The signal is then input to volume (VR1) . The adjusted

signal is sent to the audio power amplifier (IC117) through pin 1 to drive the

speaker.

All manuals and user guides at all-guides.com

5. Squelch Circuit

The detected output which is outputted from the pin 11 of IC108 is inputted to

pin 13 of IC108 after it was been amplified by IC104:A and it is outputted from

pin 14 after the noise component was been eliminated from the composed

band pass filter in the built in amplifier of the IC, then the signal is rectified by

D106 to convert into DC component. The adjusted voltage level at VR101 is

delivered to the comparator of the CPU.

The voltage is led to pin 2 of CPU and compared with the setting voltage. The

squelch will open if the input voltage is lower than the setting voltage.

During open squelch, pin 30 (SQC) of the CPU becomes "L" level, AF control

signal is being controlled and sounds is outputted from the speaker.

6. WIDE/NARROW switching circuit

The 2nd IF 455 KHz signal which passes through filter FL101 (wide) and FL102

(narrow) during narrow, changes its width using the width control switching

IC103 and IC102.

8) Transmitter System (DR-435)

1. Modulator Circuit

The audio signal is converted to an electrical signal by the microphone, and

input it to the microphone amplifier (Q6). Amplified signal which passes through

mic.mute control IC109 is adjusted to an appropriate mic. volume by means of

mic. gain adjust VR106.

IC114:A and B consists of two operational amplifiers; one amplifier (pins 1, 2,

and 3) is composed of pre-emphasis and IDC circuits and the other (pins 5, 6,

and 7) is composed of a splatter filter. The maximum frequency deviation is

obtained by VR107. and input to the signal switch (IC113) (9600 bps packet

signal input switch) and input to the cathode of the varicap of the VCO, to

change the electric capacity in the oscillation circuit.This produces the frequency

modulation.

2. Power Amplifier Circuit

The transmitted signal is oscillated by the VCO, amplified by the drive amplifier

(Q131, Q125) and younger amplifier (Q115), and input to the final power module

(IC110).The signal is then amplified by the final power module (IC110) and led

to the antenna switch (D110) and low-pass filter (L116, L114, L115, C215,

C216, C202, C203 and C204), where unwanted high harmonic waves are

reduced as needed, and the resulting signal is supplied to the antenna.

3. APC Circuit

Part of the transmission power from the low-pass filter is detected by D111 and

D112, converted to DC. The detection voltage is passed through the APC

circuit(Q118, Q117, Q116), then it controls the APC voltage supplied to the

younger amplifier Q115 and the final power module IC110 to fix the transmission

power.

All manuals and user guides at all-guides.com