Allegro Network Multimeter 1300 Bedienungsanleitung

Installation Guide

Allegro Network Multimeter

1300, 3300 and 5300

Default Settings

LAN: DHCP client

Wi-Fi SSID: allegro-mm-(see top label)

Wi-Fi URL:https://allegro/ or

https://192.168.4.1

Wi-Fi WPA2 key: Allegro-MM

Web interface username: admin

Web interface password: allegro

Overview

The guide contains the following sections:

1. Package Contents

2. Hardware Deployment

3. Device Start

4. Management Interface Configuration

5. Configuration Reset

6. Firmware Update Notification

7. IP KVM Interface

8. Factory Reset

9. Manual

1. Package Contents

The Allegro Network Multimeter package contains the following items:

1 x Allegro Network Multimeter 1300, 3300 or

5300 incl. redundant power supply

2 x Power cable

1 x Rack rails

1 x Wi-Fi USB adapter (already pre-installed)

1 x Screw set for HDDs or U.2 SSDs

10 x 2.5” HDD Mounting frame

2 x 2.5“ U.2 NVMe Mounting frame

1 x Installation guide

2. Hardware Deployment

2.1. Management Access (Control Plane)

Step 1: Connect power supply

éé

power supply

Step 2: Connect management LAN

Alternative: Insert Wi-Fi adapter to

any of the USB ports éé

IP KVM MGMT

By default, for LAN, the device will query an IP address via DHCP dynamically from your network.

By default, for Wi-Fi, the device starts an Access Point (AP) so that smartphones, tablets or laptops can

connect to the AP and access the web interface.

In case Wi-Fi access is not possible and no DHCP server exists, a temporary IP address can be assigned

by using a USB keyboard and pressing ‘Shift+S’. The LAN IP interface is temporarily set to 192.168.0.1.

If this is already taken, another address in the range from 192.168.0.1 to 192.168.0.10 will be used. You

can check the assigned IP address on a connected monitor.

2.2. Network Measurement Installation (Data Plane)

The Allegro x300 analyzes all traffic transmitted through one of the network interfaces of the built-in

measurement cards. The Allegro Network Multimeter can be ordered with up to 3 network cards with

2 or 4 ports each. The appliance can be used in the following configurations:

2.2.1. Bridge Mode

Each 2 adjacent ports of a network card form a Layer 2 bridge, which forwards all incoming data traffic

to the corresponding interface.

WARNING: Bridge mode is a software-only TAP and will not work in case of a device error or power

down.

2.2.2. Sink Mode

Received packets will be processed, but not forwarded. Connect the Allegro Network Multimeter to a

hardware TAP by connecting both TAP interfaces to the device. Alternatively, a switch or router mirror

port can be connected to any of the device network interfaces.

Default configuration is bridge mode, thus running as an inline device. The link mode can be configured

via a web interface (menu ‘Settings →Global settings’):

2.3 Install your own HDDs or U.2 NVMe SSDs

The Allegro x300 can be used with up to 10 2.5" SATA HDDs. These must be mounted in the built-in

frame.

The 2 drive bays on the right side support

2 U.2 NVMe SSDs.

3. Device Start

1. Press the power button at the front of the device. The device will boot within two minutes.

2. LAN access: The device gets its IP address from the DHCP server in your network. Check the

console output on an attached monitor or ask the server administrator for the IP address of the

device, then enter the IP address into the URL bar of your web browser.

3. Wi-Fi access:

• SSID: allegro-mm-xxxx (individual per device)

• WPA2 password: Allegro-MM

• Enter https://allegro/ or https://192.168.4.1/ into the URL bar of your web browser.

4. Web interface authentication:

• Username: admin

• Password: allegro

4. Management Interface Configuration

You can configure the management interfaces by accessing the web interface at ‘Settings →Manage-

ment interface settings’. The available options are described in the online manual which can be accessed

via the web interface.

5. Configuration Reset

The Configuration Reset restores the configuration to the default settings.

1. Web interface: Go to menu ‘Settings -> Administration’ and click on ‘Reset system configura-

tion’. All settings including the network configuration will be reset to factory default.

2. Boot menu: Follow the instruction in the section 8. Factory Reset.

The mounting frames for the U.2 NVMe are

identified by the lettering "NVMe" on the front

panel.

6. Firmware Update Notification

Update information via email

With each release, Allegro Packets will send you an email with release notes and a link to download the

update. If you want to be added to this mailing list, please send an email with the device serial number

(‘Info -> System Info -> System ID’) to [email protected] and the subject ‘Release’.

Using the Allegro web interface

Start your Allegro Network Multimeter and click ‘Settings’ in the menu and then ‘Firmware updates’.

Click on ‘Check for new firmware’ and the Allegro Network Multimeter will tell you if a new version is

available for download. If so, you can choose to download it directly to the device. In addition, this page

provides an overview of all versions available to you. To install the new version, click on ‘Activate’.

7. IP KVM Interface

The device supports a dedicated IPMI-based device management which can be accessed by connecting

the ‘IP KVM’ port to your network. The vendor of the interface is SuperMicro, so please refer to the IPMI

manual available here: http://www.supermicro.com/manuals/other/SMT_IPMI_Manual.pdf.

8. Factory Reset

The factory reset will clear the entire system installation and restore the firmware to the version that

was originally shipped with the Allegro Network Multimeter.

1. Power off the Allegro x300.

2. Remove all network cables from the device.

3. Connect a display to the VGA ports.

4. Connect a USB keyboard to any USB port.

5. Power on the device by pressing the power button.

6. After initialization a boot menu appears for 3 seconds. Select ‘Factory reset’ and press Enter. Or

select ‘Configuration reset’ to reset the configuration settings only while keeping the current

firmware installation.

7. The device will boot, reset everything to factory settings, and reboot again.

8. The device is now reset to factory settings.

9. Disconnect the display and keyboard.

9. Manual

The device manual can be accessed from the web interface. Each web section contains a button to

access context-specific documentation. The complete manual can be opened by clicking on the ‘Manual’

link in the menu.

Getting help:

Please send an email to support@allegro-packets.com

or call +49 341 59 16 43 54

Dieses Handbuch passt für folgende Modelle

Andere Allegro Multimeter Handbücher

Allegro

Allegro 1000 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung