Allen-Bradley SLC 5/03 Bedienungsanleitung

Publication 1747-IN009C-MU-P - December 2002

Installation Instructions

SLC 5/03™, SLC 5/04™, and SLC 5/05™

Modular Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553

1747-L542P, 1747-L543P, 1747-L553P)

To Use Publication

Install your chassis

Installation du châssis

Installation des Chassis

Installazione dello chassis

Instalar el chasis

Instalar o chassi

1746-IN016A-MU-P

Install your power supply

Installation de l’alimentation

Installation des Netzteils

Installazione dell’alimentatore

Instalar la fuente de alimentación eléctrica

Instalar a fonte de energia

1746-IN004B-MU-P

Install your processor

Installation de processeur

Installation des Prozessors

Installazione del processore

Instalar el procesador

Instalar o processador

1747-IN009B-MU-P

English Section.................................... 3

Section en français ........................... 15

Deutscher Abschnitt.......................... 27

Sezione in Italiano............................. 39

Sección en español........................... 51

Seção em português ......................... 63

Allen-Bradley Parts

Publication 1747-IN009C-MU-P - December 2002

Installation Instructions

English Section

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular

Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553,

1747-L542P, 1747-L543P, 1747-L553P)

Inside…........................................................................................ page

Important User Information ................................................................. 4

For More Information........................................................................... 5

Required Tools and Equipment............................................................ 6

Safety Considerations.......................................................................... 6

Installation Procedure.......................................................................... 7

Troubleshooting ................................................................................. 11

Specifications .................................................................................... 11

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA)...... 13

Allen-Bradley Parts

4SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Important User Information

Because of the variety of uses for the products described in this publication, those responsible

for the application and use of this control equipment must satisfy themselves that all

necessary steps have been taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this guide are

intended solely for purposes of example. Since there are many variables and requirements

associated with any particular installation, Allen-Bradley does not assume responsibility or

liability (to include intellectual property liability) for actual use based upon the examples

shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation, and

Maintenance of Solid-State Control (available from your local Allen-Bradley office), describes

some important differences between solid-state equipment and electromechanical devices

that should be taken into consideration when applying products such as those described in

this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part, without

written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout these installation instructions we use notes to make you aware of safety

considerations:

Attention statements help you to:

•identify a hazard

•avoid the hazard

•recognize the consequences

ATTENTION

Identifies information about practices or circumstances that can lead

to personal injury or death, property damage or economic loss.

IMPORTANT Identifies information that is critical for successful application and

understanding of the product.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 5

Publication 1747-IN009C-MU-P - December 2002

For More Information

If you would like a manual, you can:

•download a free electronic version from the internet:

www.theautomationbookstore.com

•purchase a printed manual by:

–contacting your local distributor or Rockwell Automation representative

–visiting www.theautomationbookstore.com and placing your order

–calling 1.800.963.9548 (USA/Canada)

or 001.330.725.1574 (Outside USA/Canada)

For Refer to this Document Pub. No.

A more detailed description on how to

install and use your modular SLC 500

system.

SLC 500 Modular Hardware

Style User Manual 1747-UM011C

A reference manual that contains status

file data, instruction set, and

troubleshooting information.

SLC 500 Instruction Set

Reference Manual 1747-RM001C

Allen-Bradley Parts

6SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Required Tools and Equipment

•medium blade screwdriver

•programming equipment

•1747-CP3 cable or appropriate network interface

Safety Considerations

For general recommendations concerning installation safety requirements and safety related

work practices, refer to the requirements specific to your region.

•Europe: Reference the standards found in EN 60204 and your national regulations.

•United States: refer to NFPA 70E, Electrical Safety Requirements for Employee Workplaces.

Network Interface SLC 5/03 SLC 5/04 SLC 5/05

1747-PIC X

1747-CP3 X X X

1747-KTX, -PKTX X(1)

(1) requires 1784-CP14 cable

X(3)

(3) requires 1784-CP13 cable

1747-PCMK X(2)

(2) requires 1784-PCM4 cable

X(4)

(4) requires 1784-PCM6 cable

10Base-T EtherNet X

ATTENTION

Never install, remove, or wire any module while power is applied.

Also, do not expose processor modules to surfaces or other areas that

may typically hold an electrostatic charge. Electrostatic charges can

alter or destroy memory.

IMPORTANT See page 13 for information on proper battery handling, storage, and

transporting.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 7

Publication 1747-IN009C-MU-P - December 2002

Installation Procedure

Install the Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746 chassis.

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LEDs. The power LED on the power

supply should be on and the fault LED on the processor should be flashing. See the

figure on page 8 for location of the power supply and processor LEDs.

IMPORTANT The SLC 500 modular processors must be inserted into the left slot

(slot 0), as shown below. In addition, remove the protective wrap after

installing the processor.

Power Supply

Protective Wrap

Card Guide

Processor Release

Allen-Bradley Parts

8SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Load Your Software

Refer to your programming software documentation.

Establish Communication to the Processor

1. Refer to the following table to establish communication between the processor and

your personal computer.

Processor: Procedure:

SLC 5/03 Connect 1747-PIC from the processor to your personal computer serial port or use a

1784-KTX, -PKTX, or -PCMK interface, or a 1747-CP3 cable from channel 0 of the

processor to the personal computer serial port.

SLC 5/04 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port or use a 1784-KTX, -PKTX, or -PCMK interface.

SLC 5/05 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port. For Ethernet connection, connect channel 1 of the processor and the PC

Ethernet Card to an Ethernet hub using 10Base-T compatible cable.(1)

(1) Ethernet IP address must first be set via BOOTP or an RS-232 connection.

POWER RUN

FLT

BATT

FORCE

DH485

RS232

POWER RUN

FLT

BATT

FORCE

DH+

RS232

POWER RUN

FLT

BATT

FORCE

ENET

RS232

Power Supply and LED Indicators

Indicates the LED is OFF

Indicates the LED is ON

Indicates the LED is FLASHING

Status of LED does not matter

SLC 5/05

SLC 5/04

SLC 5/03

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 9

Publication 1747-IN009C-MU-P - December 2002

2. Set the communication parameters of the software to match the default parameters of

the processor:

Replacing the Battery

Your SLC processor provides back-up power for RAM through a replaceable lithium battery.

This battery provides back-up for approximately 2 years. The BATT LED on the front of the

processor alerts you when the battery voltage has fallen below a threshold level.

To replace the lithium battery follow these steps:

1. Remove power from the SLC 500 power supply.

2. Remove the processor from the chassis by pressing the retainer clips at both the top

and bottom of the module and slide it out.

Channel 0 Configuration Channel 1 Configuration

SLC 5/03, 5/04, 5/05 SLC 5/03 SLC 5/04 SLC 5/05

DF1 Full-Duplex:

•no handshaking

•19.2K baud

•CRC Error Check

•duplicate detect on

•no parity

DH-485:

•19.2K baud

•node address = 1

DH+™:

•57.6K baud

•node address = 1

Ethernet

•BOOTP

enabled

ATTENTION

Do not remove the processor from the SLC 500 chassis until all

power is removed from the SLC 500 power supply

ATTENTION

Do not expose the processor to surfaces or other areas that may

typically hold an electrostatic charge. Electrostatic charges can alter or

destroy memory.

Allen-Bradley Parts

10 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

3. Unplug the battery connector. Refer to the figure on page 10 for battery connector

location.

4. Remove the battery from the retaining clips.

5. Insert a new battery into the battery retaining clips.

6. Plug the battery connector into the socket as shown above.

7. Re-insert the module into the SLC 500 chassis.

8. Restore power to the SLC 500 power supply.

9. Close the processor door.

IMPORTANT The SLC 5/03, 5/04, and 5/05 processors have a capacitor that

provides at least 30 minutes of battery back-up while the battery is

disconnected. Data in RAM is not lost if the battery is replaced within

30 minutes

IMPORTANT See page 13 for information on proper battery handling, storage, and

transporting.

White

Red

Battery Connector

Left Side View

Battery

Andere Handbücher für SLC 5/03

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Allen-Bradley Computerhardware Handbücher

Allen-Bradley

Allen-Bradley 2707-MVH232 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Mini-PLC Mini-PLC-2/16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2707 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2094-AL15S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-SF1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 5/03 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 5/04 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 5/01 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 5/01 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-DCM Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 MAP/OSI Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung