Allen-Bradley 1771-P4S Bedienungsanleitung

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the Rockwell / Allen-Bradley 1771-P4S at our website: Click HERE

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1, -P6S1)

Installation Data

AllenBradley

Power Supply Modules

(cat. no. 1771-P4S, -P6S, -P4S1, -P6S1)

This document provides you with the following information:

what this package contains

tasks on installing your power supply module

interpreting the power supply indicators

troubleshooting your power supply

When you receive your power supply, you should see the following

components in the box:

one 1771-P4S, -P6S, -P4S1, or -P6S1 power supply module

one 5-position terminal block (attached to module)

To install your power supply, you need to know how to perform the

following tasks:

set the jumpers

place the power supply in a chassis

connect a paralleling cable (if using a second supply)

connect input power

Set the Jumpers

Each power supply module has two jumpers located at the back edge of the

module near the gold-plated edge connectors. The jumper selection

provides the proper voltage regulation for the different power supply

configurations. The power supply can be configured to support local or

remote sensing by setting the jumpers.

the Installer

What This Power Supply

Package Contains

Installing the Power Supply

Module

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1)

Installation Data

To configure the supply:

1. Position the power supply module so that the jumpers and pins are

facing upward as shown in figure 1.

Figure 1

Power Supply Jumpers

2. Set the jumpers as shown in table A. Use needle nose pliers to set the

jumpers.

Table A

Jumper Settings

For This Configuration Set Jumpers to:

A single power supply in a powersupply chassis

connected to an I/O chassis through a power cable.

right position

All other configurations. (Power supplies are

shipped with jumpers in this position.)

left position

Place the Power Supply in a Chassis

WARNING: Turn off all power-supply modules before

removing modules from or inserting modules into a chassis.

Failure to observe this warning could alter processor memory,

damage module circuitry, and cause unintended operation which

could possibly cause injury to personnel.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1, -P6S1)

Installation Data

You can place these power-supply modules into any I/O module slot in any

current chassis (1771-A1B, -A2B, -A3B, -A4B, -A3B1, -PSC).

However, to place these power-supply modules into a superseded I/O

chassis (1771-A1, -A2, -A4), you must follow the restrictions in table B.

Table B

Placement Restrictions in Superseded I/O Chassis (1771A1, A2, A4)

Adapter or

Inchassis

processor

I/O

Chassis

1st

Power Supply12nd

Power Supply1

Without A4 I/Oslot 0 I/Oslot 10

an integral

power supply

A2 I/Oslot 0 I/Oslot 4

power supply A1 I/Oslot 0 not applicable

With an integral A4 not applicable I/Oslot 8

power supply A2 not applicable I/Oslot 3

1I/O

module slots are numbered 0 through 15, left to right.

Connect a Paralleling Cable

You can use two power supplies in the same I/O chassis to produce more

power by connecting them with a Power-Supply Paralleling Cable

(1771-CT). This connection is for communication between the two

supplies. If one supply has to shut down, it tells the second to turn off its

indicator. Although the adapter or in-chassis processor will be disabled, the

second supply will continue trying to operate until its DC output limits are

exceeded. Because the adapter or in-chassis processor is disabled,

paralleling two supplies does not provide redundancy.

To connect the paralleling cable:

1. Connect the paralleling cable between the P/S PARALLEL

connectors on the two supplies (figure 2).

2. Loop the paralleling cable over the top of the I/O chassis to avoid

picking up signals induced from I/O wiring.

3. Turn on the supplies simultaneously. If you don’t, the first supply you

turn on may shut down due to an overcurrent condition.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1)

Installation Data

Figure 2

Paralleling Cable and AC Power Connections

Connect Input Power

Figure 2 shows the overall configuration of the ac power connections.

To make ac power connections:

1. Connect the high side of the power source to the L1 terminal of the

power supply.

2. Connect the low side of the power source to the L2 or N (neutral)

terminal of the power supply.

3. Connect the GND (ground) terminal of the power supply to the

central ground bus in the enclosure.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1, -P6S1)

Installation Data

Figure 3 shows details of how to connect a wire to a terminal on the

terminal block. You can connect these wires while the terminal block is

plugged into the supply, or you can remove the block to lay it on a flat

surface to connect these wires. To remove the block, pull it straight out out

from the receptacle on the module.

The 2 undesignated terminals do not connect to any electrical circuit on the

module and are not used. Each of the three functional terminals accepts a

single 14-AWG wire max.

To connect a wire to a terminal:

1. Strip 0.35 inches of insulation off the wire.

2. Spring the clip open to insert the wire, using a wedge-tipped tool such

as a small screwdriver. If you leave the terminal block plugged into

the supply, insert the tool parallel to the wire (push straight in). If you

remove the terminal block and lay it on a flat surface, insert the tool

perpendicular to the wire (push straight down).

3. After making the wiring connections, re-insert the terminal block into

the front plate. Be sure that the plug is completely inserted and that

the locking prongs are engaged.

Figure 3

Connecting a W

ire to a Terminal

Your power supply has an indicator located in the upper half of the module

front panel labeled P/S ACTIVE. Table C shows how to interpret the P/S

ACTIVE indicator.

Interpreting the Power Supply

Indicators

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1)

Installation Data

Table C

Interpreting the P/S ACTIVE Indicator

If the indicator

Is:

Then:

On The power supply (and any supply connected through a paralleling cable) is

operating normally. However, it could still have a poor connection to the

backplane.

Off The supply has detected one of the following conditions:

Gdc overvoltage (the supply shuts down)

Gdc undervoltage (the supply shuts down)

Gdc overcurrent (the supply shuts down)

Gpower switch turned off (the supply is turned off)

Gac undervoltage

Gthe paralleled supply is shut down

With ac undervoltage or a paralleled supply shut down, the supply will still

attempt to generate the output. When dc limits are exceeded, the supply shuts

down until you turn power off (for 5 seconds minimum) and then back on.

If you have a single power supply installed in an I/O chassis and its P/S

ACTIVE indicator is off, verify the ground connection to the supply; then

follow this troubleshooting flow chart.

Troubleshooting a Single

Power Supply

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1, -P6S1)

Installation Data

If you have a pair of power supplies installed in parallel in an I/O chassis

and the P/S ACTIVE indicators are off, verify the ground connection to

each supply; then follow this troubleshooting flow chart.

Troubleshooting

Parallel

Power Supplies

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Power Supply Modules

(Cat. No. 1771-P4S, -P6S, -P6S1)

Installation Data

Specifications

1771P4S 1771P6S 1771P4S1 1771P6S1

Input Voltage 120V ac 220V ac 100V ac 200V ac

Input Range 97 132V ac rms 194 - 264V ac rms 85 - 120V ac rms 170 - 240V ac rms

Frequency 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz 47 - 63 Hz

Fuse 1.5A 250V Slowblow

Output Voltage (Backplane) 5V dc

Output Current (max) 8A

Wire Size 14 AWG max (single wire only)

Environmental Conditions Operational Temperature: 0 to 60°C (32 to 140 °F)

Storage Temperature: 40 to 85°C (40 to 185 °F)

Relative Humidity: 5 to 95% (without condensation)

Physical Width 1 I/O chassis slot

Weight 1.85 lbs (0.84 kg)

5position Terminal Block AB P/N 94127405, Wago 1 P/N 231205/000008 (1 included with each power supply)

1Wago

Corporation 9085 N. Deerbrook T

rail, Brown Deer WI 53223

With offices in major cities worldwide

WORLD

HEADQUARTERS

Allen-Bradley

1201 South Second Street

Milwaukee, WI 53204 USA

Tel: (1) 414 382-2000

Telex: 43 11 016

FAX: (1) 414 382-4444

EUROPE/MIDDLE

EAST/AFRICA

HEADQUARTERS

Allen-Bradley Europe B.V.

Amsterdamseweg 15

1422 AC Uithoorn

The Netherlands

Tel: (31) 2975/43500

Telex: (844) 18042

FAX: (31) 2975/60222

ASIA/PACIFIC

HEADQUARTERS

Allen-Bradley (Hong Kong)

Limited

Room 1006, Block B, Sea

View Estate

28 Watson Road

Hong Kong

Tel: (852) 887-4788

Telex: (780) 64347

FAX: (852) 510-9436

CANADA

HEADQUARTERS

Allen-Bradley Canada

Limited

135 Dundas Street

Cambridge, Ontario N1R

5X1

Canada

Tel: (1) 519 623-1810

FAX: (1) 519 623-8930

LATIN AMERICA

HEADQUARTERS

Allen-Bradley

1201 South Second Street

Milwaukee, WI 53204 USA

Tel: (1) 414 382-2000

Telex: 43 11 016

FAX: (1) 414 382-2400

As a subsidiary of Rockwell International, one of the world’s largest technology

companies — Allen-Bradley meets today’s challenges of industrial automation with over

85 years of practical plant-floor experience. More than 11,000 employees throughout the

world design, manufacture and apply a wide range of control and automation products

and supporting services to help our customers continuously improve quality, productivity

and time to market. These products and services not only control individual machines but

integrate the manufacturing process, while providing access to vital plant floor data that

can be used to support decision-making throughout the enterprise.

Publication 1771–2.135–February 1990

Supersedes Publication 1771–2.135–Febuary 1989 PN 955106–86

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Artisan

Technology

Group

an independent supplier

quality pre-owned equipment

Gold-standard

solutions

Extend the life

your

critical industrial,

commercial, and military systems

with

our

superior service and support.

buy

equipment

Planning to

upgrade

your current

equipment? Have surplus equipment taking

up shelf space? We'll give it a

new

home.

Learn

more!

Visit us at artisantg.com for more info

on price quotes, drivers, technical

specifications, manuals, and documentation.

Artisan Scientific

Corporation

dba

Artisan

Technology

Group

not

an affiliate,

representative,

authorized

distributor

for

any

manufacturer

listed herein.

We're here to make your life easier.

How

can

help you today?

(217)

352-9330

Isales@artisantg.com Iartisantg.com

Dieses Handbuch passt für folgende Modelle

Andere Allen-Bradley Stromversorgung Handbücher

Allen-Bradley

Allen-Bradley 1609-HDK1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-PA75/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLERED20Y Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-N Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-N Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-EP24DC Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-PA2K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLB36EH Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-PA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS960F-3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-PA75R/A Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS240E Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLB Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLB480E Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLE480EP-D SER B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-EP24DC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLE240ERL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLE480FP-D Bedienungsanleitung

Allen-Bradley

Allen-Bradley Bulletin 1606 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-P2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700 AFE Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLB60E Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung