Allen-Bradley 802T Bedienungsanleitung
Installation Instructions
Original Instructions
Four-Circuit Direct Opening Action Limit Switch
Catalog Numbers
802T
Overview
Bulletin 802T Direct Opening Action limit switches have been
designed for use in applications requiring control reliability
performance per ANSI B11.19 and in safety applications
Limit switches are used in electrical control systems to sense position.
They are actuated by the predetermined motion of a cam, machine
component or piece part. These limit switches are suitable for use in
control systems requiring control reliability performance or safety
related performance per ISO 13849–1.
Typical Example of a Dual Channel Safety Application
Before installation in a safety application, a risk assessment should be
performed to determine whether the specifications of this device are
suitable for foreseeable operational and environmental characteristics
of the machine which is to be controlled. Only the normally closed set
of contacts are considered safety contacts. When applying these limit
switches in a safety system application, all applicable standards for
application should be followed. Operating specifications must be
followed and actuator must be displaced beyond the point where
Direct Opening Action occurs. These devices are not to be used to
directly control a motor.
General Data
• Safety Contacts: 2 Normally Closed
• Auxiliary Contacts: 2 Normally Open
• Enclosure Rating:
• NEMA 4, 6P, 12, and 13
•IP67
•
Operating rate and speed
1
• Lever Type: 150/minute @ 9 m (30 ft)/minute
2
• Top Push Roller: 150/minute @ 9 m (30 ft)/minute
3
• Side Push Roller: 150/minute @ 9 m (30 ft)/minute
3
•
Operating temperature (standard models) 18…110°C
(0…230°F)
• Short Circuit Protection: 10 amp slow or 15 amp fast acting.
Overload protection should be sized to load requirements.
Mounting
Limit switches should be securely mounted using the mounting holes
provided. During installation, ensure that the actuator will be displaced
beyond the point where Direct Opening Action takes place. Adjustable
levers or rod actuators should not be used in safety systems
applications.
1Based on operation temperatures of 20…30°C (68…86°F).
2Using 802T-W1A operating lever.
3Using 30° non-overtravel dog.
Wiring
The pressure type connector terminals in the base will accept No.
12AWG and smaller solid or stranded wire. For proper tightening, it is
suggested that nothing smaller than No. 18 AWG be used. Before
inserting wire under the pressure plates, strip the insulation
approximately 3/8 inch. Tighten all pressure plate terminals whether
used or not, to avoid interference with the switch cover.
AT TEN T ION: To avoid electrical shock and
unintended operation of equipment, disconnect
all power to the limit switch and the controlled
equipment before proceeding with any repair or
adjustment of the limit switch.
ATTENTION : Adjustable length lever actuators should not be used
in a safety systems application.
1
2
5
6
3
4
7
8
Description Tightening Torque
Terminal Screws 2.03 N•m (18 lb•in)
Front to Rear Base 1.81…2.26 N•m (16…20 lb•in)
Head Screws 1.35…2.03 N•m (12…18 lb•in)
Lever Arm 2.82…4.07 N•m (25…36 lb•in)
IMPORTANT The contacts in each switching element must have the same
polarity. The circuit diagram is shown on the nameplate.
Allen-Bradley, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 802T-IN004A-EN-P - September 2002 PN–462117
Copyright © 2002 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
After wiring has been completed, check that all wires are in the wiring
cavity of the terminal block so they will not interfere with the switch
when it is plugged into the terminal block.
Recheck all wiring terminal screws for tightness.
Note: For switches that have been factory wired, check wire color and
their position in the terminal block for proper circuit hookup.
• Grounding of switch should be achieved per National Electric
Code (NFPA 70) requirements. Grounding terminal is located in
the terminal block housing.
• Arrange control wiring according to terminal markings.
• Tighten terminal screws according to specifications.
• Only use insulated connectors.
Actuator Head Positioning
The actuator head may be placed in any of four positions on the switch
body. Loosen the four captive screws. Place the head in the desired
position and securely re-tighten the four screws (see figure below).
Lever Positioning
The lever on rotary actuated devices is adjustable to any position
through 360° around the shaft. Loosen the nut, move
the lever to the
desired position and securely re-tighten the nut (see figure below).
Changing Direction of Actuation
The switch action of lever operated limit switches may be adjusted to
operate in either a clockwise, a counterclockwise, or both directions
movement of the shaft.
To change the actuation direction, follow the steps below:
Step 1: Loosen the four head mounting screws and remove the
operating head from the switch body.
Step 2: Locate the plunger on the underside of the operating head.
Step 3: Pull the plunger outward and rotate it in steps of 90 ° to
provide the operating mode desired. The respective settings are shown
in the figure below.
Step 4: Make sure the plunger is pushed back inward and the “O” ring
is properly seated before the operating head is reattached to the switch
body.
Step 5: Securely re-tighten the operating head mounting screws.
Step 6: Check for the desired actuation mode.
Methods of Actuation Examples
IMPORTANT Pay close attention to the terminal numbering on the
terminal block when wiring this switch. Terminals 1 and 2 or
5 and 6 are normally open contacts.
Terminals 3 and 4 or 7 and 8 are normally closed contacts.
IMPORTANT This procedure must be performed in a clean environment to
avoid the introduction of foreign material into the operating
mechanism.
802T–APD
802T–W1A 1.5 in. long
90 Non-overtravel Dog
802T–DPD
Top Push Roller
30 Non-overtravel Dog
802T–KPD
Side Push Roller
30 Non-overtravel Dog
Vmax = 30 ft/min @ actuator
F max = 150 cycles/min
Inhaltsverzeichnis
Andere Allen-Bradley Schalten Handbücher
Allen-Bradley
Allen-Bradley 194L Bedienungsanleitung
Allen-Bradley
Allen-Bradley SensaGuard 440N-Z21S16A Bedienungsanleitung
Allen-Bradley
Allen-Bradley 194R-LFC03 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Guardmaster Lifeline 4 Bedienungsanleitung
Allen-Bradley
Allen-Bradley GuardLogix 5570 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Guard master Sprite Bedienungsanleitung
Allen-Bradley
Allen-Bradley 140G-R Series Bedienungsanleitung
Allen-Bradley
Allen-Bradley 198-MR7 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 440P Bedienungsanleitung
Allen-Bradley
Allen-Bradley Stratix 5700 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 105-C09 Series Bedienungsanleitung
Allen-Bradley
Allen-Bradley Stratix 8000 Bedienungsanleitung
Allen-Bradley
Allen-Bradley ferrogard gd2 Bedienungsanleitung
Allen-Bradley
Allen-Bradley TLS-GD2 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Guardmaster 440G-LZS21SJLJ Bedienungsanleitung
Allen-Bradley
Allen-Bradley Rockwell Automation ArmorBlock... Bedienungsanleitung
Allen-Bradley
Allen-Bradley Stratix 5400 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 440G-A07269 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Stratix 5200 1783-CMS6B Bedienungsanleitung
Allen-Bradley
Allen-Bradley 105-PW23 Bedienungsanleitung
