Allen-Bradley PanelView Plus 2711P Bedienungsanleitung

2711PPanelViewPlus

Operator Terminals

700, 1000, 1250, 1500

User Manual

AB PLCs

Important User Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of these

products must satisfy themselves that all necessary steps have been

taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations,

codes and standards. In no event will Rockwell Automation be

responsible or liable for indirect or consequential damage resulting

from the use or application of these products.

Any illustrations, charts, sample programs, and layout examples

shown in this publication are intended solely for purposes of

example. Since there are many variables and requirements associated

with any particular installation, Rockwell Automation does not assume

responsibility or liability (to include intellectual property liability) for

actual use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation and Maintenance of Solid-State Control

(available from your local Rockwell Automation office), describes

some important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole

or part, without written permission of Rockwell Automation, is

prohibited.

Throughout this publication, notes may be used to make you aware of

safety considerations. The following annotations and their

accompanying statements help you to identify a potential hazard,

avoid a potential hazard, and recognize the consequences of a

potential hazard:

PanelView, PanelView Plus, RSView and VersaView are trademarks of Rockwell Automation.

Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.

WARNING

Identifies information about practices or

circumstances that can cause an explosion in a

hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION

Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

iPublication2711P-UM001A-EN-P

Table of Contents

Preface

Objectives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-i

Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-i

Manual Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-ii

Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-ii

Related Publications . . . . . . . . . . . . . . . . . . . . . . . . Preface-iii

European Communities (EC) Directive Compliance . Preface-iii

Rockwell Automation Support . . . . . . . . . . . . . . . . . Preface-iv

Chapter 1

Overview

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Software Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Modular Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Base Configured Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Communication Modules. . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Remote AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Display Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Catalog Number Configuration. . . . . . . . . . . . . . . . . . . . . . 1-7

Product Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Chapter 2

Installation

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . 2-2

Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Panel Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Chapter 3

Applying Power

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Wiring and Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . 3-1

Applying DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Applying AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Resetting the Terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Startup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Chapter 4

Using Configuration Mode

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Starting Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . 4-1

Loading an ME Application . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Running an Application. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Application Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

AB PLCs

Publication 2711P-UM001A-EN-P

Table of Contents ii

Terminal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Networks and Communications . . . . . . . . . . . . . . . . . . . . . 4-6

Diagnostic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

File Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Input Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Print Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Startup Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

System Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

Time/Date/Regional Settings . . . . . . . . . . . . . . . . . . . . . . . 4-34

Chapter 5

Installing and Replacing

Components

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Installing RAM and Internal Compact Flash . . . . . . . . . . . . 5-2

Installing and Replacing the Logic Module . . . . . . . . . . . . . 5-3

Installing/Replacing a Communication Module . . . . . . . . . . 5-5

Replacing the Display Module . . . . . . . . . . . . . . . . . . . . . . 5-7

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

Replacing Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

Replacing Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

Installing the Remote AC Power Supply . . . . . . . . . . . . . . . 5-16

Removing the Product Label . . . . . . . . . . . . . . . . . . . . . . . 5-16

Installing Keypad Legend Inserts . . . . . . . . . . . . . . . . . . . . 5-17

Using an External Compact Flash Card. . . . . . . . . . . . . . . . 5-18

Chapter 6

Terminal Connections

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Wiring and Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . 6-1

Logic Controller Cable Charts . . . . . . . . . . . . . . . . . . . . . . 6-2

USB Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Serial Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Ethernet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

DH-485/DH+/Remote I/O Module . . . . . . . . . . . . . . . . . . . 6-10

Chapter 7

Transferring files

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Using a Compact Flash Card . . . . . . . . . . . . . . . . . . . . . . . 7-1

Publication2711P-UM001A-EN-P

Table of Contents iii

Chapter 8

Troubleshooting and Maintenance

Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Troubleshooting Components . . . . . . . . . . . . . . . . . . . . . . 8-3

Ethernet Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Advanced Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 8-8

System Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

System Identification Errors . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Restarting in Configuration Mode. . . . . . . . . . . . . . . . . . . . 8-11

Startup Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Restarting in Safe Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

Cleaning the Display Window . . . . . . . . . . . . . . . . . . . . . . 8-14

Appendix A - Specifications

Index

AB PLCs

Publication 2711P-UM001A-EN-P

Table of Contents iv

iPublication2711P-UM001A-EN-P

Preface

Objectives

This preface provides information on the contents of this manual

including:

•contents of manual

•intended audience

•European Union Directive Compliance

•Rockwell Automation Support

Packing List

The following items are shipped with an assembled PanelView Plus

terminal:

•DC power terminal block

•RSView Machine Edition Runtime

•Mounting clips (up to 8)

•Microsoft Windows CE License Agreement

•Installation guide

AB PLCs

Publication 2711P-UM001A-EN-P

Preface ii

Manual Contents

Intended Audience

No special knowledge is required to understand this manual or

operate the PanelView Plus terminal. However, it is important that you

understand the functions and operations of Machine Edition

applications that will run on the terminal. Consult the application

designer for this information.

Chapter Title Description

1 Overview Provides overview of the PanelView

Plus terminals including features and

product components.

2 Installation Gives Instructions on how to install

the PanelView Plus terminal in a

panel or enclosure.

3 Applying Power Describes how to apply power and

reset the PanelView Plus terminal.

4 Using Configuration Mode Shows how to use the PanelView

Plus configuration screens to

load/run applications and configure

terminal settings for the PanelView

Plus terminal.

5 Installing and Replacing

Components Shows how to install and replace

components of the VersaView CE

terminal including:

•Logic Module

•RAM/Internal Compact Flash

•Communication Module

•Display Module

•Battery

•Display Module Bezel

•Backlight

•AC Power Supply

•Product Label

•Keypad Legend Inserts

•External Compact Flash Card

6 Terminal Connections Describes connections on the base

unit of the PanelView Plus terminal

and the communication modules.

7 Transferring Files Provides information on transferring

files using an External Compact Flash

Card.

8 Troubleshooting Provides assistance on isolating

operating problems.

Publication2711P-UM001A-EN-P

Preface iii

Equipment installers must be familiar with standard panel installation

techniques.

Related Publications

You may want to refer to the following for additional information:

•online help for RSView Studio or RSLinx

•documentation for your logic controller or processor

European Communities (EC)

Directive Compliance

If this product has the CE mark it is approved for installation within

the European Union and EEA regions. It has been designed and tested

to meet the following directives.

EMC Directive

This product is tested to meet the Council Directive 89/336/EC

Electromagnetic Compatibility (EMC) by applying the following

standards, in whole or in part, documented in a technical construction

file:

•EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial

Environment

•EN 61000-6-2 EMC - Generic Immunity Standard, Part 2 -

Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage, by applying the safety requirements of EN 61131-2

Programmable Controllers, Part 2 - Equipment Requirements and

Tests. For specific information required by EN 61131-2, see the

appropriate sections in this publication, as well as the Allen-Bradley

publication Industrial Automation Wiring and Grounding Guidelines

For Noise Immunity, publication 1770-4.1.

Open style devices must be provided with environmental and safety

protection by proper mounting in enclosures designed for specific

application conditions. See NEMA Standards publication 250 and IEC

publication 529, as applicable, for explanations of the degrees of

protection provided by different types of enclosure.

AB PLCs

Publication 2711P-UM001A-EN-P

Preface iv

Rockwell Automation

Support

Before you contact Rockwell Automation for technical assistance, we

suggest you please review the troubleshooting information contained

in this publication first.

If the problem persists, call your local Rockwell Automation

representative or contact Rockwell Automation in one of the following

ways:

Software and Firmware Upgrades

To receive software updates (software serial number required) and

firmware upgrades for your terminal:

•call your local Rockwell Automation sales office or distributor

•call Rockwell Software at 1-440-646-7800 or fax 1-440-646-7801

•access www.software.rockwell.com

Phone United

States/Canada 1.440.646.5800

Outside United

States/Canada You can access the phone number for your

country via the Internet:

1. Go to http://www.ab.com

2. Click on Product Support

(http://support.automation.rockwell.com)

3. Under Support Centers, click on Contact

Information

Internet

⇒

1. Go to http://www.ab.com

2. Click on Product Support

(http://support.automation.rockwell.com)

Andere Handbücher für PanelView Plus 2711P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Touch-Terminal Handbücher

Allen-Bradley

Allen-Bradley 2711-K5A series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView C200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-PT1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 2711P-RW1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 1200 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 800 2711R-T4T Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P Gebrauchsanweisung

Allen-Bradley

Allen-Bradley MobileView 2711T-B10R1K1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1790-T16BV0X Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MobileView 2711T-T10R1N1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 2711P Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O SCANport 1203-FB Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 2711C-F2M Bedienungsanleitung

Allen-Bradley

Allen-Bradley DeviceNet 1790D-T16BV0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PV300 Micro Bedienungsanleitung

Allen-Bradley

Allen-Bradley 8510SA-TP Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView Plus 6 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PanelView 600 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung