Allen-Bradley 1609-P8000E Bedienungsanleitung

41063-261-01(1) 990-2672 09/2005

Allen-Bradley

User Manual for 8000/10000 VA UPS

1609-P8000E 8000 VA 200-240 VAC

1609-P10000E 10000 VA 200240 VAC

Tower/Rack-Mount 6U

Uninterruptible Power Supply

INSTALLATION

Read the safety information sheet before installation.

Unpacking

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents:

qUPS

qTwo front bezels

qLiterature kit containing:

qPowerChute®Business Edition CD

qBulletin 1609-P Series User Manual CD

q1609-NMC (Network Management Card installed in slot located in rear of unit)

qNetwork Management Card CD

qSerial cable

qQuick Start Guide

Removing the Batteries

The unit is heavy. To lighten the unit, remove the batteries. Refer to the unpacking instructions on

the carton in which the unit is shipped.

Environmental Specifications

TEMPERATURE

OPERATING

STORAGE

32°to104°F (0°to40°C)

5°to 113°F (-15to45 °C) charge UPS battery every six months

MAXIMUM

ELEVATION

OPERATING

STORAGE

10,000 ft (3,000 m)

50,000 ft (15,000 m)

HUMIDITY 0% to 95% relative humidity, non-condensing

This unit is intended for

indoor use only. Select a

location sturdy enough to

handle the weight.

Do not operate the UPS where

there is excessive dust or the

temperature and humidity are

outside the specified limits.

Ensure the air vents on the

front and rear of the UPS

are not blocked.

Hardwiring

Wiring must be performed by a qualified electrician.

1. Install a utility circuit breaker in accordance with local electrical codes (see tables below) for

input wiring only.

2. Switch the UPS input circuit breaker and utility circuit breakers OFF.

3. Remove the access panel.

4. Remove circular knockouts.

5. Run wires through access panel to terminal blocks. Wire to ground block first. Adhere to all

national and local electrical codes.

6. Use appropriate glands to achieve strain-relief on the hardwired input and output power cables.

InputConnection OutputConnection(optional)

Wire to L1, L2, Wire to L1A, L2A,

System Wiring Voltage Current

Full Load

(Nominal)

External Input

CircuitBreaker

(typical)

WireSize

(typical)

1609-P8000E Input & Output 208/230 V40 A

XLTW-38 A50 A/ 2-pole for

Input Wiring Only

Allen-Bradley

Catalog Number

1492-MCAA2H50

#8AWG/

10mm2

1609-P10000E Input & Output 208/230 V54 A

XLTW-50 A70 A/ 2-pole for

InputWiringonly

Allen-Bradley

Catalog Number

1492-MCBA2H70

#6AWG/

16mm2

7. Switch the circuit breakers ON.

8. Check line voltages.

9. Replace the access panel.

Installing and Connecting the Batteries and Attaching the Front Bezel

Œ•

Ž•

•‘

Connecting Power and Equipment to the UPS

1. Hardwire the UPS (see Hardwiring).

2. Connect equipment to the UPS.

3. Turn on all connected equipment. To use the UPS as a master on/off switch, be sure that all

connected equipment is switched ON.

4. Press the button on the front panel to power up the UPS.

•The battery charges to 90% capacity during the first three hours of normal operation. Do not

expect full battery run capability during this initial charge period.

OPTIONS

qExternal Battery Pack (1609-PXBP)

qRail Installation Kit (1609-PRK1)

qIsolation Transformer(1609-5000CCT)

CIRCUIT BREAKERS

Input Circuit Breaker

8000/10000 VA

The UPS is protected from extreme overloads when in ON position.

The breaker must be on for the UPS to operate.

Output Circuit Breaker

8000/10000 VA

BASIC CONNECTORS

serial port

Power management software and interface cable can be used with the

UPS.

Use onlya supplied or approved interface cable.

Any other serial interface cable will be incompatible with the UPS

connector.

EPO Terminal

The optional Emergency Power Off (EPO) feature allows connected

loads to be immediately de-energized from a remote location, without

switching to battery operation (see EPO Option).

TVSS Screw

The UPS features a transient voltage surge-suppression (TVSS) screw

for connecting the ground lead on surge suppression devices such as

telephone and network line protectors.

When connecting grounding cable, disconnect the unit from the utility

power outlet.

external battery pack

connectors

Optional external battery packs provide extended runtime during

power outages. These units support up to 10 external battery packs.

OPERATION

FRONT DISPLAY PANEL

Indicator Description

Online

The UPS is drawing utility power and performing double conversion to supply

power to connected equipment (see Troubleshooting).

On Battery

The UPS is supplying battery power to the connected equipment.

Bypass

The UPS is in bypass mode, sending utility power directly to connected equipment.

Bypass mode operation is the result of an internal UPS fault, an overload condition

or a user initiated command either through an accessory or the manual bypass

switch. Battery operation is not available while the UPS is in bypass mode (see

Troubleshooting).

Fault

The UPS detects an internal fault (see Troubleshooting).

Overload

The connected loads are drawing more power than the UPS power rating (see

Troubleshooting).

Replace

Battery

The battery is disconnected or must be replaced (see Troubleshooting).

Feature Function

Power On

Press this button to turn on the UPS. (Read on for additional capabilities.)

Power Off

Press this button to turn off the UPS.

Feature Function

Normal /Bypass

Manually switch connected equipment to bypass mode, so that utility power is

sent directly to connected equipment. Battery operation is not available while

the UPS is in bypass mode. (See Troubleshooting.)

Cold Start

This is not a normal condition.

Supply immediate battery power to the UPS and connected equipment

(see Troubleshooting). Press and hold the button to power up the UPS and

connected equipment. The UPS will emit two beeps. During the second beep,

release the button.

Self-Test Automatic: The UPS performs a self-test automatically when turned on, and

every two weeks thereafter (by default). During the self-test, the UPS briefly

operates the connected equipment on battery.

Manual: Press and hold the button for a few seconds to initiate the self-

test.

DiagnosticUtility

Voltage

The UPS has a diagnostic feature that displays the utility voltage. Plug the UPS

into the normal utility power.

The UPS starts a self-test as part of this procedure. The self-test does not

affect the voltage display.

Press and hold the button to view the utility voltage bar graph display.

After a few seconds the five-LED, Battery Charge display on the right of

the front panel shows the utility input voltage.

Refer to the figure at left for the voltage reading (values are not listed on the

UPS).

The display indicates the voltage is between the displayed value on the list and

the next higher value.

On Battery Operation

The UPS switches to battery operation automatically if the utility power fails. While running on

battery, an alarm beeps four times every 30 seconds.

Press the button to silence this alarm. Ifthe utility power does not return, the UPS continues to

supply power to the connected equipment until the battery is fully discharged.

When two minutes of runtime remain the UPS emits a continuous beep. If PowerChute or the

Web/SNMP card is not being used, files must be manually saved and the computer must be properly

shut down before the UPS fully discharges the battery.

USER CONFIGURABLE ITEMS

NOTE:SETTINGS ARE MADE THROUGH SUPPLIED POWERCHUTE SOFTWARE,

OPTIONAL NETWORK MANAGEMENT CARDS,OR TERMINAL MODE.

FUNCTION FACTORY

DEFAULT USER SELECTABLE

CHOICES DESCRIPTION

Automatic Self-Test Every 14 days

(336 hours) Every 7 days

(168 hours),

Every 14 days

(336 hours),

On Startup Only,

No Self-Test

Set the interval at which the

UPS will execute a self-test.

UPS ID UPS_IDEN Up to eight characters to

define the UPS Uniquely identify the UPS, (i.e.

server name or location) for

network management purposes.

Date of Last Battery

Replacement Manufacture Date mm/dd/yy Reset this date when you replace

the battery modules.

Minimum Capacity

Before Return from

Shutdown

0 percent 0, 15, 25, 35, 50, 60, 75,

90 percent Specify the percentage to which

batteries will be charged

following a low-battery

shutdown before powering

connected equipment.

Alarm Delay After

Line Failure 5 second delay 5 second delay,

30 second delay,

At Low Battery,

Never

Mute ongoing alarms or disable

all alarms permanently.

Shutdown Delay 20 seconds 0, 20, 60, 120, 240, 480,

720, 960 seconds Set the interval between the time

when the UPS receives a

shutdown command and the

actual shutdown.

Duration of

Low Battery Warning.

2 minutes

PowerChute

software provides

automatic,

unattended

shutdown when

approximately two

minutes of battery

runtime remains.

2, 5, 7, 10, 12, 15, 18,

20 minutes. The low battery warning beeps

become continuous when two

minutes of runtime remains.

Change the warning interval to a

higher setting if the operating

system requires a longer interval

for shutdown.

Synchronized Turn-on

Delay 0 seconds 0, 20, 60, 120, 240, 480,

720, 960 seconds Specify the time the UPS will

wait after the return of utility

power before turn-on (to avoid

branch circuit overloads).

High Bypass Point

+10% of

output voltage

setting

+5%, +10%, +15%,

+20% Maximum voltage that the UPS

will pass to connected

equipment during internal

bypass operation.

NOTE:SETTINGS ARE MADE THROUGH SUPPLIED POWERCHUTE SOFTWARE,

OPTIONAL NETWORK MANAGEMENT CARDS,OR TERMINAL MODE.

FUNCTION FACTORY

DEFAULT USER SELECTABLE

CHOICES DESCRIPTION

Low Bypass Point -30% of output

voltage setting -15%, -20%, -25%, -30% Minimum voltage that the UPS

will pass to connected

equipment during internal

bypass operation.

Output Voltage 208/230 V models:

230 VAC 208/230 V models:

200, 208, 220,

230, 240 VAC

Allows the user to select the

UPS output voltage while

online.

Output Frequency Automatic

50 ± 3 Hz or

60 ± 3 Hz

50 ± 3 Hz

50 ± 0.1 Hz

60 ± 3 Hz

60 ± 0.1 Hz

Sets the allowable UPS output

frequency. Whenever possible,

the output frequency tracks the

input frequency.

Number of Battery

Packs 1 Number of Connected

Batteries (four battery

modules per pack)

Defines the number of

connected battery packs for

proper runtime prediction.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley UPS Handbücher

Allen-Bradley

Allen-Bradley Bulletin 1609 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1609-P3000N Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS240-UPSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1609-P3000N Bedienungsanleitung

Allen-Bradley

Allen-Bradley Bulletin 1609 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DC-UPS Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung