Allen + Roth 873X-5B04 Bedienungsanleitung

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

You could also contact us at [email protected].

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

_________________________

Tub & Shower Faucet

ITEM # 0702750 / 5287441

MODEL # 873X-5B04 / 873X-5B01

Español p. 12

AS23202

_________________________

ALLEN & ROTH and logo design are

trademarks or registered trademarks of LF, LLC.

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Shower Flange 1

B Shower Arm 1

C Showerhead 1

D Valve Body 1

E Escutcheon 1

F Handle Assembly 1

G Plug 1

H Tub Spout 1

I Plaster guard 1

J Screw 2

K Bonnet (Preassembled to Valve Body (D)) 1

L Cartridge (Preassembled to Valve Body (D)) 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the

product.

WARNING

• Follow the installation instructions carefully. Proper installation is the installer’s responsibility.

• Failure to follow correct installation procedures can result in the faucet being loose, which can

result in serious injury.

CAUTION

• Check local building codes before you begin installation to ensure compliance.

ASSEMBLY INSTRUCTIONS

1. Prepare the bath area for installation:

a. Shut off the water supply to the tub and shower.

Note: This may require shutting off the main water

supply to your home.

b. Verify that the hole sizes and positions in the

wall are correct. Here are the recommended

component measurements:

– Shower and Spout Outlet Hole: 1-1/4 in.

diameter

– Valve Access Hole: 6 in. diameter

– Recommended Valve Depth to Finished Wall:

2-1/2 in. min. to 3 in. max. Ensure that the

black template plate’s surface is with the

exterior surface of the wall. Position

the valve body correctly in the wall. The 8 in.

minimum from the valve body to the tub spout

is required for proper operation.

PREPARATION

Before beginning the assembly of this product, make sure all parts are present. Compare parts with

the package contents list. If any part is missing or damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes (including removal of old faucet)

Tools Required for Assembly (not included): Adjustable Wrench, Phillips Screwdriver,Thread Sealant

Tape

Helpful Tools (not included): Safety Goggles

30 in.

Tub & Shower

8 in. Min.

48 in.

Shower Only

1 1/4 in. Diamter

1 1/4 in. Diameter

48 in.

Tub & Shower

Refer to

the step 2

30 in.

Shower Only

2. Unscrew the screws (J), and remove the plaster

guard (I).

ASSEMBLY INSTRUCTIONS

3. Installing the supply connections:

a. Wrap thread sealant tape around the pipe threads

in a clockwise direction, as shown.

b. Connect the hot and cold water supply lines

(1, not included), the shower (2, not included) and

tub outlet pipes (3, not included) to the valve body

(D). Connect the pipe elbows (4, not included) to

the ends of both pipes, and tighten with a wrench.

See Figure 3a.

c. If you do not wish to install the tub outlet, thread

the plug (G) into the bottom outlet. See Figure 3b.

NOTE: Be sure to position the body (D) correctly in

the wall, with the markings "UP" facing upward.

The hot water supply lines go into the H inlet,

and the cold water supply lines go into the C inlet.

Do not use PEX or CPVC between the valve

and spout.

HOT COLD

Copper

or IPS

HOT COLD

4. Back to back installation

If the hot and cold inlets are reversed (hot on right and

cold on left), remove the screws (J), plaster guard (I),

and bonnet (K) from the valve body (D) with reversed

supply connections. Rotate the cartridge (L) 180°,

so H appears on the right. Install the cartridge making

sure that the key is fully engaged with the slot in the

valve body (D). Slide the bonnet (K) over the cartridge

(L) and thread them onto the valve body (D). Hand

tighten securely. Reassemble the plaster guard (I) and

screws (J). If you are not making a reverse or back to

back installation, skip this step and continue with the

step 5.

NOTE: Never install the valve body (D) upside down!

5. Flushing:

a. Attach the handle assembly (F) by threading the

base of the handle assembly (F) onto the valve

body (D) and twisting clockwise until secure.

b. Turn the handle assembly (F) to the on position.

Turn on the hot and cold water supply lines and

allow the water to flow from the outlets for one

minute, or until all foreign matter has been

flushed out. Check for leaks.

c. Shut off the water at the faucet and supply lines.

Remove the handle assembly (F).

ASSEMBLY INSTRUCTIONS

6. Place the plaster guard (I) onto the body (D) and

secure with the screws (J).

Normal Installation

Reverse Installation

Cold Hot

Cold

Hot

Normal

Installation

(changes

not

required)

Cold

Hot

Reverse

Installation

8. Install the tub spout (H):

a. Wrap thread sealant tape around the pipe thread

of the tub spout (H) outlet in a clockwise direction,

as shown.

b. Thread the spout (H) onto the threaded connection

in a clockwise direction until the spout (H) becomes

flush with the finished wall. Use the strap wrench to

tighten the spout (H).

9. Before installing the escutcheon, remove the plastic

cap (1) from the valve body (D) by twisting the cap

in a clockwise direction.

ASSEMBLY INSTRUCTIONS

7. Install the shower arm (B):

a. Insert the long end of the shower arm (B) through

the flange (A), then wrap thread sealant tape

around long end of the shower arm (B) in a

clockwise direction, as shown.

b. Install the long end of the shower arm (B) into the

pipe elbow inside the wall. Tighten the shower

arm (B), do not over tighten.

c. Wrap thread sealant tape around the pipe threads

of the tub spout outlet (1, not included) in a clockwise

direction, as shown. Connect the tub spout outlet

pipe (the tub spout outlet pipe should project

4-1/8 in. to 4-89/32 in. from the finished wall) to the

lower pipe elbow (2, not included). Tighten the elbow

and tub spout outlet pipe connections with a wrench.

4-1/8 in. to 4-9/32 in.

Wall

11. Installing the escutcheon, handle and showerhead:

a. Attach the handle assembly (F) by threading the

base of the handle assembly (F) onto the valve stem

of the valve body (D) and twisting clockwise until

secure. Do not overtighten the handle assembly (F) a

s this could damage the escutcheon (E).

b. Install the showerhead (C) to the end of the shower

arm (B) by twisting in a clockwise direction.

Hand-tighten only.

ASSEMBLY INSTRUCTIONS

10. Checking for leaks:

a. Attach the handle assembly (F) by threading the

base of the handle assembly (F) onto the valve

body (D) and twisting clockwise until secure. Turn

the handle assembly (F) to the on position.

b. When the valve is turned on, water normally flows

through the tub spout (H). To activate the shower,

turn the valve on and pull the knob (1) up. Hold the

knob (1) until the water flows continiously from the

shower arm (B).

c. Check for leaks.

d. Shut off the water at the faucet and supply lines.

Remove the handle assembly (F).

Up for

shower

Up for

shower

Down

2. Remember the position of the stop ring (1) on

the cartridge assembly (L). Remove the stop

ring (1) from the cartridge assembly (L).

ADJUSTING THE TEMPERATURE LIMITER AND WATER FLOW ON THE VALVE

1. Unscrew and remove the handle assembly (F) and

escutcheon (E) from the valve body (D).

The limiter on the valve can be set to allow partial or full access to hot water by limiting how far the

handle can be turned to the hot side of the valve. The limiter is typically set at the factory to allow only

warm water to pass through the valve. Follow the directions in this section if you wish to adjust the

amount of hot water that is allowed through the valve.

For colder water For hotter water

ADJUSTING THE TEMPERATURE LIMITER AND WATER FLOW ON THE VALVE

3. To adjust for the desired maximum water temperature:

a. For colder water, adjust the stop ring (1) in a

clockwise direction and reinstall the stop ring (1)

onto the cartridge assembly (L).

b. For hotter water, adjust the stop ring (1) in a

counterclockwise direction and reinstall the stop

ring (1) onto the cartridge assembly (L).

NOTE: A thermometer (not included) can be held

in the running water to aid in reaching the desired

water temperature.

4. Replace the escutcheon (E) and handle assembly (F)

back onto the valve body (D). Do not overtighten the

handle (F) as this could damage the escutcheon (E).

NOTE: Rotate the cartridge stem (1) clockwise to

turn off the water before you install the handle.

CARE AND MAINTENANCE

• Clean carefully by gently wiping with a grit-free damp cloth.

• Use only mild soap with water.

• Never use acids, harsh chemicals, or abrasive detergents to clean the faucet surface.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE NOITCAEVITCERROC

The showerhead

has reduced water

flow.

The showerhead is dirty. 1. Remove the showerhead and

clear any debris clogged at the

shower connection.

2. If the problem occurs after clearing

the debris, call customer service

for a new showerhead and replace

it after you receive the new

showerhead.

The tub spout has

no or reduced water

flow.

Angle stops or stop valves are not

open completely.

Open angle stops and stop valves

completely. (Rotating the stop valves

with a flathead screwdriver (not

included) in a counterclockwise

direction until the stop valves cannot

rotate. This is the position where the

stop valves are open completely.)

There is a leak from

showerhead and

shower arm

connection.

1. Using the thread sealant tape to

seal the showerhead and shower arm

connection.

2. The seal washer in the showerhead

is missing.

1. Remove the showerhead, remove

the thread sealant tape between

showerhead and shower arm, then

attach the showerhead to shower

arm directly. Because there is a seal

washer in the showerhead, it has a

seal function.

2. Call customer service for a new

showerhead and replace it after you

receive the new showerhead.

There is a leak from

under the handle or

there is a leak from

the spout when the

faucet is off.

1. The bonnet nut is not tight enough.

2. The cartridge is damaged.

1. Remove the handle and retighten

the bonnet nut.

2. If the problem occurs after

retightening the bonnet nut, call

customer service for a new cartridge

and replace it after you receive the

new cartridge.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Allen + Roth Badezimmerarmatur Handbücher

Allen + Roth

Allen + Roth Roveland 2026VA-30-242-906 Bedienungsanleitung

Allen + Roth

Allen + Roth 1605VA-48-201-925 Bedienungsanleitung

Allen + Roth

Allen + Roth Davidson-48GP-ORB Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20525 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-60-201 Bedienungsanleitung

Allen + Roth

Allen + Roth LANCASHIRE 30CB Bedienungsanleitung

Allen + Roth

Allen + Roth 1315VA-60-201 Bedienungsanleitung

Allen + Roth

Allen + Roth PU-21EW-SS Bedienungsanleitung

Allen + Roth

Allen + Roth WSL36RVSW Bedienungsanleitung

Allen + Roth

Allen + Roth FS6A0230CP Bedienungsanleitung

Allen + Roth

Allen + Roth Davidson-32SP-CH Bedienungsanleitung

Allen + Roth

Allen + Roth Reagan 72-BVF11-BB-AR Bedienungsanleitung

Allen + Roth

Allen + Roth 22-2835-33 Bedienungsanleitung

Allen + Roth

Allen + Roth Roveland 2026VA-30-200-901 Bedienungsanleitung

Allen + Roth

Allen + Roth Davidson-TD-CH Bedienungsanleitung

Allen + Roth

Allen + Roth 1315VA-48-201 Bedienungsanleitung

Allen + Roth

Allen + Roth 4065451 Bedienungsanleitung

Allen + Roth

Allen + Roth VBL10SBNK Bedienungsanleitung

Allen + Roth

Allen + Roth Ellum-SC-60GP-CH Bedienungsanleitung

Allen + Roth

Allen + Roth BRINKHAVEN 30AG 2694591 Bedienungsanleitung

Allen + Roth

Allen + Roth Davidson-60GP-CH Bedienungsanleitung

Allen + Roth

Allen + Roth 20053-0501 Bedienungsanleitung

Allen + Roth

Allen + Roth 20053-2001 Bedienungsanleitung

Allen + Roth

Allen + Roth WSL36RVE Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

Kohler

Kohler K-13056 Montageanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung