Alliance Laundry Systems ADEE9BGS433XW34 Bedienungsanleitung

Installation Instructions

for Dryers

Original Instructions

Keep These Instructions for Future Reference.

CAUTION: Read the instructions before using the machine.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com Part No. D516105R2

August 2017

WARNING

Risk of fire. Highly flammable material.

W881

Hazardous voltage inside. Disconnect power before serv-

icing.

Read all instructions before using unit.

WARNING

FOR YOUR SAFETY, the information in this manual

must be followed to minimize the risk of fire or ex-

plosion or to prevent property damage, personal in-

jury or death.

W033

WARNING

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

• WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Clear the room, building or area of all occu-

pants.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s in-

structions.

• If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed by a

qualified installer, service agency or the gas sup-

plier.

W052

IMPORTANT: Purchaser must consult the local gas

supplier for suggested instructions to be followed if

the dryer user smells gas. The gas utility instructions

plus the SAFETY and WARNING note directly above

must be posted in a prominent location near the dryer

for customer use.

WARNING

• Installation of unit must be performed by a quali-

fied installer.

• Install clothes dryer according to manufacturer’s

instructions and local codes.

• DO NOT install a clothes dryer with flexible plas-

tic venting materials. If flexible metal (foil type)

duct is installed, it must be of a specific type

identified by the appliance manufacturer as suita-

ble for use with clothes dryers. Refer to section

on connecting exhaust system. Flexible venting

materials are known to collapse, be easily crush-

ed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

W729R1

WARNING

To reduce the risk of severe injury or death, follow all

installation instructions. Save these instructions.

W894

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable va-

pors and liquids in the vicinity of this or any other

appliance.

W053

This product uses FreeRTOS V7.2.0 (www.freertos.org).

DO NOT COPY or TRANSMIT

3 Part No. D516105R2

Table of Contents

Introduction........................................................................................... 5

Model Identification........................................................................................5

Dimensions............................................................................................. 6

Installation............................................................................................. 8

Before You Start............................................................................................. 8

Supplies..................................................................................................... 8

Order of Installation Steps............................................................................8

Position and Level the Dryer............................................................................8

Connect Dryer Exhaust System...................................................................... 10

Exhaust Direction......................................................................................11

Exhaust System.........................................................................................12

Gas Dryers - Connect Gas Supply Pipe........................................................... 12

Reverse Door, if Desired................................................................................14

Wipe Out Inside of Dryer...............................................................................15

Plug In the Dryer.......................................................................................... 15

Electrical Requirements............................................................................. 15

Earth/Ground Instructions.......................................................................... 17

Recheck Steps.............................................................................................. 17

Check Heat Source........................................................................................17

Electric Dryers.......................................................................................... 17

Gas Dryers................................................................................................17

All Dryers.................................................................................................18

Installer Checklist.................................................................................19

written consent of the publisher.

DO NOT COPY or TRANSMIT

4 Part No. D516105R2

Introduction

Model Identification

Information in this manual is applicable to these dryer models:

ADEE9BGS433XW34

ADEE9BSS433XN34

Introduction

DO NOT COPY or TRANSMIT

5 Part No. D516105R2

Dimensions

Electric Models

DRY2638N_SVG

A * 1027 mm [40.42 in.]

B * 1006 mm [39.61 in.]

C * 392 mm [15.44 in.]

D * 102 mm [4 in.]

E 391 mm [15.4 in.]

F 683 mm [26.875 in.]

G * 114 mm [4.5 in.]

H 10 mm [0.4 in.]

I 203 mm [8 in.]

J 711 mm [28 in.]

K 597 mm [23.5 in.]

NOTE: Exhaust openings are 102 mm [4 inch] metal

ducting.

* With leveling legs turned into base.

Gas Models

DRY2639N_SVG

M L

1. 3/8 in. NPT Gas Connection

Dimensions

DO NOT COPY or TRANSMIT

6 Part No. D516105R2

A *1027 mm [40.42 in.]

B *1006 mm [39.61 in.]

C *392 mm [15.44 in.]

D *70 mm [2.8 in.]

E 60 mm [2.3 in.]

F 391 mm [15.4 in.]

G 683 mm [26.875 in.]

H 102 mm [4 in.]

I *114 mm [4.5 in.]

J 10 mm [0.4 in.]

K 203 mm [8 in.]

L 711 mm [28 in.]

M 597 mm [23.5 in.]

NOTE: Exhaust openings are 102 mm [4 inch] metal

ducting.

* With leveling legs turned into base.

NOTE: Gas models cannot be vented out left side of

cabinet because of burner housing.

IMPORTANT: The dryer should have sufficient clear-

ance around it for needed ventilation and for the ease

of installation and servicing. For maximum drying per-

formance, we recommend that more clearance be al-

lowed around the dryer than the clearances that are lis-

ted throughout this manual.

Dimensions

DO NOT COPY or TRANSMIT

7 Part No. D516105R2

Installation

Before You Start

Supplies

For most installations, the basic supplies you will need are:

DRY2586N_SVG

765

1. Wrench

2. 1/4 inch Driver

3. Screwdrivers

4. Level

5. Gloves

6. Teflon Tape

7. Duct Tape

8. Safety Glasses

Figure 1

NOTE: This appliance is suitable for use in countries

having a warm, damp climate.

WARNING

Any disassembly requiring the use of tools must be

performed by a suitably qualified service person.

W299

Order of Installation Steps

1. Position and level the dryer.

2. Connect dryer to exhaust system.

3. For gas models only, connect the gas supply pipe. Check for

gas leaks.

4. Reverse the door, if desired.

5. Wipe out the inside of the dryer.

6. Connect the dryer to electrical power.

7. Recheck steps.

8. Start and run the dryer in a heat setting to verify dryer is heat-

ing.

Position and Level the Dryer

1. Install dryer before washer. This allows room for attaching

exhaust duct.

2. Select a location with a solid floor. Dryers installed in resi-

dential garages must be elevated 457 mm [18 inches] above

the floor.

No other fuel burning appliance should be installed in the same

closet with the dryer.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

The dryer needs sufficient clearance and an adequate air supply

for proper operation and ventilation, and for easier installation

and servicing. (Minimum clearances are shown in Figure 3 ).

The dryer must not be installed behind a lockable door, a sliding

door or a door with a hinge on the opposite side to that of the dry-

er, in such a way that a full opening of the dryer door is restricted.

3. Place the dryer in position, and adjust the legs until the dryer

is level from side to side and front to back. Leveling legs can

be adjusted from inside the dryer with a 1/4 in. driver.

4. All four legs must rest firmly on the floor so the weight of the

dryer is evenly distributed. The dryer must not rock.

DRY2500N_SVG

1. Dryer Base

2. Level

3. Leveling Leg

Figure 2

Installation

DO NOT COPY or TRANSMIT

8 Part No. D516105R2

Front View (Without Closet Door)

DRY2640N_SVG

Side View (Closet Door)

DRY2641N_SVG

Front View (Closet Door)

DRY2637N_SVG

2 (G)

1. Closet Door

2. Centered Air Openings (G) (2 Openings minimum)

3. Outer Wall of Enclosure

Figure 3

Installation

DO NOT COPY or TRANSMIT

9 Part No. D516105R2

Area Description

Free Standing/Alcove In-

stallation Closet Installation

A* Dryer sides and rear clearance 0 mm [0 in.] 0 mm [0 in.]

B Dryer top clearance 305 mm [12 in.] 305 mm [12 in.]

C Dryer front clearance Not Applicable 51 mm [2 in.]

D Exhaust duct clearance to com-

bustible material

51 mm [2 in.] 51 mm [2 in.]

E Weather hood to ground clear-

ance

305 mm [12 in.] 305 mm [12 in.]

F Distance from floor or ceiling

to air opening edge

Not Applicable 76 mm [3 in.]

G Area of centered air openings

in closet door. Louvered door

with equivalent air openings is

acceptable. (Minimum clearan-

ces are shown.)

Not Applicable 1016 sq. mm/open [40 sq. in./

open]

H For new installations, it is sug-

gested to locate top of wall vent

1067 mm [42 inches] above

floor to make venting easier to

connect.

1067 mm [42 in.] 1067 mm [42 in.]

* Rear clearance is minimum. 51 mm [2 inches] is recommended for utility connection. 152 mm [6

inches] is recommended when venting through rear of unit.

Table 1

IMPORTANT: In mobile home installations, gas dryers

MUST be permanently attached to the floor at the time

of installation. Order No. 526P3 Hold Down Kit (availa-

ble at extra cost) for a manufactured (mobile) home in-

stallation. Follow the instructions supplied with the kit.

Connect Dryer Exhaust System

WARNING

To reduce the risk of fire and combustion gas accu-

mulation the dryer MUST be exhausted to the out-

doors.

W604

WARNING

To reduce the risk of fire and the accumulation of

combustion gases, DO NOT exhaust dryer air into a

window well, gas vent, chimney or enclosed, unven-

tilated area, such as an attic, wall, ceiling, crawl

space under a building or concealed space of a

building.

W045

WARNING

To reduce the risk of fire, DO NOT use plastic or thin

foil ducting to exhaust the dryer.

W354

Installation

DO NOT COPY or TRANSMIT

10 Part No. D516105R2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Alliance Laundry Systems Trockner Handbücher

Alliance Laundry Systems

Alliance Laundry Systems UT025 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UA025L Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SWD439C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LWS01M series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems BD3LLFGS401UW01 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY725C Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CA120L Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FES17AxF Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems AES17AWF Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems DR5004WE Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems ADEE8B BLACK Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 504522R3 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 0904004427 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY724C_SVG Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems DR3003WX Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRYING TUMBLERS 70269501R3 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY735C-SVG Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY688C Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY710C Leitfaden

Alliance Laundry Systems

Alliance Laundry Systems DRY2024N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems DRY2195N Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems BA025E Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 504523R3 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UniLinc 35 Series Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung

Samsung

Samsung DV431AEPXAC Bedienungsanleitung