Alliance Laundry Systems Speed Queen FR7002WN Bedienungsanleitung

Installation Instructions

for Frontload Washers

Original Instructions

Keep These Instructions for Future Reference.

CAUTION: Read the instructions before using the machine.

(If this machine changes ownership, this manual must accompany machine.)

www.speedqueen.com Part No. 806989ENR1

March 2019

Table of Contents

Washer Dimensions................................................................................ 4

Installation............................................................................................. 5

Before You Start............................................................................................. 5

Tools............................................................................................................. 5

Parts Included.................................................................................................5

Parts Needed.................................................................................................. 5

Order of Installation Steps............................................................................... 5

Position Unit Near Installation Area................................................................. 5

Remove Shipping Materials.............................................................................6

Connect Fill Hoses..........................................................................................7

Water Supply Requirements......................................................................... 7

Connecting Hoses....................................................................................... 7

Connect Drain Hose to Drain Receptacle.......................................................... 8

Standpipe Installation.................................................................................. 8

Wall Installation.......................................................................................... 8

Laundry Tub Installation..............................................................................9

Position and Level the Washer......................................................................... 9

Wipe Out Inside of Wash Drum......................................................................10

Plug In the Washer........................................................................................ 10

Electrical Requirements............................................................................. 10

Earth/Ground Instructions.......................................................................... 11

Check Installation......................................................................................... 11

Installer Checklist.................................................................................12

written consent of the publisher.

DO NOT COPY or TRANSMIT

3 Part No. 806989ENR1

Washer Dimensions

FLW2462N_SVG

JIH

Figure 1

A 24.06 in. [611 mm]

B 23.19 in. [589 mm]

C (to controls) Electronic Control: 41.25 in. [1048 mm]

Knob Control: 40.75 [1035 mm]

D 42.75 in. [1086 mm]

E 32 in. [813 mm]

F 36 in. [914 mm]

G * 14.6 in. [371 mm]

H 26.875 in. [683 mm]

I 2.04 in. [52 mm]

J 27.73 in. [704 mm]

K (with door closed) 1.59 in. [40 mm]

L 13.1 in. [333 mm]

* For ADA compliance turn legs out from base 0.5 inches.

Washer Dimensions

DO NOT COPY or TRANSMIT

4 Part No. 806989ENR1

Installation

Before You Start

Tools

For most installations, the basic tools you will need are:

FLW2376N_SVG

1. Safety Glasses

2. Wood Block

3. Wrench

4. Screwdriver

5. Pliers

6. Socket Wrench

7. Gloves

8. Level

Figure 2

NOTE: If the washer is delivered on a cold day (below

freezing), or is stored in an unheated room or area dur-

ing the cold months, do not attempt to operate it until

the washer has had a chance to warm up.

NOTE: Install dryer before washer. This allows room for

attaching exhaust duct.

NOTE: Some moisture in the wash drum is normal. Wa-

ter is used during testing at the manufacturer.

NOTE: This appliance is suitable for use in countries

having a warm, damp climate.

Parts Included

An accessories bag has been shipped inside your washer. It in-

cludes:

• Two fill hoses with washers and filter screens

• Four rubber feet

• Beaded strap

• Installation Instructions

• User’s Guide

• Warranty Bond

Parts Needed

Two fill hoses are required for installation. Order 807239 Hose

Kit if needed. Kit includes two fill hoses color-coded for hot and

cold water.

If using any other hoses, follow these requirements:

• Hoses must be new.

• Hoses must be a minimum of 3/8 in. inside diameter. Smaller

inside diameter hoses will cause long fill times which could

create nuisance fill errors.

• The two plain rubber washers and two filter screens included

with the washer in the accessories bag must be installed in the

fill hose couplings. Refer to Connecting Hoses. The filter

screens help prevent foreign materials from clogging the wa-

ter mixing valve.

Order of Installation Steps

The proper order of steps must be followed to ensure correct in-

stallation. Refer to the list below when installing your unit.

1. Position washer near the installation area.

2. Remove the shipping materials.

3. Connect the fill hoses.

4. Connect the drain hose to the drain receptacle.

5. Position and level the washer.

6. Wipe out inside of the washer.

7. Plug in the washer.

8. Check installation.

Position Unit Near Installation Area

Move unit so that it is within 4 feet [1.2 meters] of the desired

area of installation.

Installation

DO NOT COPY or TRANSMIT

5 Part No. 806989ENR1

NOTE: For best performance and to minimize vibration

or movement, install washer on a solid, sturdy and lev-

el floor. Some floors may need to be reinforced, espe-

cially on a second floor or over a basement. Do not in-

stall the washer on carpeting, soft tile or other weakly

supported structures.

Remove Shipping Materials

1. Remove two screws at bottom of front access panel. Rotate

bottom of panel out and remove panel.

FLW2378N_SVG

Figure 3

2. Remove two 9/16 inch bolts and washers holding shipping

brace to weight.

3. Remove two 9/16 inch bolts and washers holding shipping

brace to washer base and remove brace.

FLW2296N_SVG1

Figure 4

4. Go to rear of washer and pull label from rear shipping bolts.

5. Remove two 9/16 inch bolts. Unscrew each bolt while apply-

ing forward pressure just until bolt stops unthreading. Work

each bolt and spacer out by hand using a circular motion.

NOTE: Avoid backing bolts out completely or

spacers might fall into cabinet.

Installation

DO NOT COPY or TRANSMIT

6 Part No. 806989ENR1

FLW2297N_SVG1

Figure 5

6. Insert two plugs included in accessories bag into rear shipping

bolt holes.

FLW2358N_SVG

Figure 6

7. Replace front access panel.

8. Save all shipping materials. They must be reinstalled any time

washer is moved more than four feet.

IMPORTANT: Do not lift or transport unit from front

or without shipping materials installed. Refer to the

User’s Guide for proper instructions on reinstalling

the shipping materials.

Connect Fill Hoses

WARNING

Under certain conditions, hydrogen gas may be pro-

duced in a hot water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLO-

SIVE. If the hot water system has not been used for

such a period and before using the washer, turn on

all hot water faucets and let the water flow from each

for several minutes. This will release any accumulat-

ed hydrogen gas. The gas is flammable. Do not

smoke or use an open flame during this time.

W029

Water Supply Requirements

Water supply faucets must fit standard 3/4 inch [19 mm] female

garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-

ON CONNECTIONS.

NOTE: Water supply faucets should be readily accessi-

ble to permit turning them off when washer is not being

used.

Recommended cold water temperature is 50° to 75° Fahrenheit

[10° to 24° Celsius]. Recommended maximum hot water temper-

ature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture

of hot and cold water. Warm water temperature is dependent upon

the water temperature and the pressure of both the hot and cold

water supply lines.

WARNING

To prevent personal injury, avoid contact with inlet

water temperatures higher than 125° Fahrenheit [51°

Celsius] and hot surfaces.

W748

Maximum flow rate for all water temperatures is 2.5 gallons per

minute [9.46 liters per minute] ± 15%.

Water pressure must be a minimum of 20 to a maximum of 120

pounds per square inch [minimum of 138 to a maximum of 827

kPa] static pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per square

inch [138 kPa] will cause an extended fill time in the

washer and may not properly flush out the detergent

dispenser.

Turn on the water supply faucets and flush the lines for approxi-

mately two minutes to remove any foreign materials that could

clog the screens in the water mixing valve. This is especially im-

portant when installing your washer in a newly constructed or

renovated building. Build-up may have occurred during construc-

tion.

Connecting Hoses

1. Insert rubber washers and filter screens (from accessories

bag) in water fill hose couplings (two hoses supplied with

washer). The filter screen must be facing outward.

2. Connect fill hose couplings with filter screens to water supply

faucets.

3. Connect the other hose couplings to the hot and cold valve

connections at the rear of the washer.

4. Make sure the hose from the hot water faucet goes to the wa-

ter mixing valve marked “H” and the hose from the cold fau-

cet goes to the valve marked “C”.

5. Thread hose couplings onto valve connections finger tight.

Then turn 1/4 turn with pliers.

Installation

DO NOT COPY or TRANSMIT

7 Part No. 806989ENR1

IMPORTANT: DO NOT cross thread or overtighten

couplings. This will cause them to leak.

6. Turn water on and check for leaks.

7. If leaks are found, retighten the hose couplings.

8. Continue tightening and rechecking until no leaks are found.

COLD

HOT

FLW2449N_SVG

1. Filter Screen (Screen must be facing outward)

2. Fill Hose

3. Plain Rubber Washer

4. Cold Water Connection

5. Hot Water Connection

6. Install this end of hose to valve connections at rear of

washer

7. Install this end of hose to water supply faucet

8. Faucet

Figure 7

IMPORTANT:

Hoses and other rubber parts deteriorate after extend-

ed use. Hoses may develop cracks, blisters or material

wear from the temperature and constant high pressure

they are subjected to.

All hoses should be checked on a monthly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be re-

placed immediately. All hoses should be replaced ev-

ery five years.

IMPORTANT: Turn off water supply faucets after check-

out and demonstration. Owner should turn off water

supply whenever there will be an extended period of

non-use.

Connect Drain Hose to Drain

Receptacle

Remove the drain hose from its shipping position on the rear of

the washer by unhooking the hose from the retainer clamp and by

removing the shipping tape.

Install the drain hose into the drain receptacle (standpipe, wall or

laundry tub) following the instructions below.

IMPORTANT: Drain receptacle must be capable of han-

dling a minimum of 1-1/4 inch [32 mm] outside diame-

ter drain hose.

Drain Flow Rate

Drain Height

Flow Rate

gallons per minute [lit-

ers per minute]

3 ft. [0.9 m] 8.6 [32.7]

5 ft. [1.5 m] 6.8 [25.9]

6 ft. [1.8 m] 6.0 [22.7]

7 ft. [2.1 m] 5.1 [19.5]

8 ft. [2.4 m] 4.0 [15.2]

Standpipe Installation

1. Place the drain hose into the standpipe.

2. Remove the beaded tie-down strap from accessories bag and

place around standpipe and drain hose. Refer to Figure 8 .

a. Insert the end of the beaded strap into the larger hole

found on the end of the strap.

b. Tighten to desired fit.

c. Lock strap in place by pulling beaded strap into the ta-

pered smaller opening of the beaded strap end. A distinct

snap noise should be heard once the strap is properly seat-

ed.

d. Pull on the strap once locked in place to ensure beaded

strap is properly installed. This will prevent the drain hose

from dislodging from drain receptacle during use.

FLW2463N_SVG

1. 24 to 36 in. [610 to 914 mm] Recommended Height

2. Beaded strap from accessory bag

3. Standpipe 2 in. [51 mm] or 1-1/2 in. [40 mm]

Figure 8

Wall Installation

For installations of this type, the drain hose MUST be secured to

one of the fill hoses using the beaded strap from accessories bag.

Refer to Figure 9 .

Installation

DO NOT COPY or TRANSMIT

8 Part No. 806989ENR1

NOTE: End of drain hose must not be below 24 in. [610

mm].

H023i_SVG

1. Drain Hose

2. Beaded Strap (tape if necessary)

3. Fill Hoses

Figure 9

Laundry Tub Installation

For this type of installation, the drain hose MUST be secured to

the stationary tub to prevent hose from disloding during use. Re-

fer to Figure 10 . Use the beaded strap (supplied in accessories

bag) to secure hose.

FLW2464N_SVG

1. Drain Hose

2. Beaded Strap (tape if necessary)

Figure 10

Position and Level the Washer

WARNING

Washers elevated above floor level must be anch-

ored to that elevated surface, base or platform. The

material used to elevate the washer should also be

anchored to the floor to ensure that the washer will

not walk or that the washer can not be physically

pulled, tipped or slid from its installed position. Fail-

ure to do so may result in conditions which can pro-

duce serious injury, death and/or property damage.

W306

1. Position unit so it has sufficient clearance for installation and

servicing.

NOTE: Use of the dispenser drawer or washer door

as a handle in the transportation of the washer may

cause damage to the dispenser or door.

2. Place unit in position on a solid, sturdy and level floor. Instal-

ling the unit on any type of carpeting, soft tile or other weakly

supported structures is not recommended.

3. Place a level on the raised portion of cabinet top and check if

the unit is level from side to side and front to back.

4. If unit is not level, tilt unit to access the front and rear level-

ing legs. For easier access to leveling legs, prop up unit with a

wooden block.

5. Loosen 7/8 in. locknut and adjust legs by screwing into or out

of unit base until the unit is level from side to side and front

to back (using a level). Unit should not rock.

NOTE: Leveling legs can also be adjusted from in-

side the unit using an adjustable wrench.

6. Tighten the locknuts securely against the unit base. If the

locknuts are not tight, unit will move out of position during

operation.

NOTE: DO NOT slide unit across floor if the leveling

legs have been extended. Legs and base could be-

come damaged.

7. Remove rubber feet from accessories bag and place on all

four leveling legs.

8. Verify that unit doesn’t rock.

Installation

DO NOT COPY or TRANSMIT

9 Part No. 806989ENR1

FLW2465N_SVG

1. Leveling Leg

2. Washer Base

3. Level

4. Wood Block

5. Locknut

6. Rubber Foot

Figure 11

Wipe Out Inside of Wash Drum

Prior to first wash, use an all purpose cleaner or a detergent

and water solution and a damp cloth to remove shipping dust

from inside of the washer.

FLW2466N_SVG

Figure 12

Plug In the Washer

Electrical Requirements

120 Volt, 60 Hertz with 3-Prong Earth/Ground Plug

NOTE: The wiring diagram is located in the control

hood.

WARNING

To reduce the risk of fire, electric shock, serious in-

jury or death, all wiring and protective earth/ground

connections MUST conform with the latest edition of

the National Electrical Code, ANSI/NFPA No. 70, and

such local regulations as might apply. It is the cus-

tomer’s responsibility to have the wiring, fuses and

circuit breakers installed by a qualified electrician to

make sure adequate electrical power is available to

the washer.

W824

When plugging in the washer:

• DO NOT overload circuits.

• DO NOT use an extension cord.

• DO NOT use an adapter.

• DO NOT operate other appliances on the same circuit. Use

separately fused 15 Amp circuits.

The washer is designed to be operated on a separate branch, po-

larized, three-wire, effective earth/ground, 120 Volt, 60 Hertz,

AC (alternating current), circuit protected by a 15 ampere fuse,

equivalent fusetron or circuit breaker.

The three-prong earth/ground plug on the power cord should be

plugged directly into a polarized three-slot effective earth/ground

receptacle rated 110/120 Volts AC (alternating current) 15 Amps.

Refer to Figure 13 to determine correct polarity of the wall recep-

tacle.

Installation

DO NOT COPY or TRANSMIT

10 Part No. 806989ENR1

Inhaltsverzeichnis

Andere Alliance Laundry Systems Waschmaschine Handbücher

Alliance Laundry Systems

Alliance Laundry Systems HF18VNV Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CHF455 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems BWT820*N1102 Programmierhandbuch

Alliance Laundry Systems

Alliance Laundry Systems F8437801 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HC18PC2 Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems FLW63H Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems UW100TV Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HWNLX2SP111CW01 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems CS018 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HTE517xE2802 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SF135PV Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems V-Series Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems P Series Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 801405R2 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems PHM1397C Fehlerbehebungshandbuch

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount SC27SN Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen TC5000WN Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TR5000WN Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems Washer Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems FTS90A*N Montageanleitung

Alliance Laundry Systems

Alliance Laundry Systems UM202 Series Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems SA025L Betriebsanleitung

Alliance Laundry Systems

Alliance Laundry Systems LTS84A*H Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung