Allied Telesis Patch SB244-01 Bedienungsanleitung
Simply connecting the world
Patch Release Note
Patch SB244-01
For SwitchBlade 4000 Series Switches and
AT-9800 Series Switches
Introduction
This patch release note lists the issues addressed and enhancements made in
patch SB244-01 for Software Release 2.4.4 on existing models of SwitchBlade
4000 Series Switches and AT-9800 Series Switches. Patch file details are listed in
Table 1.
This release note should be read in conjunction with the following documents:
■SwitchBlade Documentation Set for Software Release 2.4.3 (Document
Number C613-03042-00 Rev E) and Release Note for Software Release 2.4.4
for SwitchBlade 4000 Switches and AT-9800 Series Switches (Document
Number C613-10342-00 Rev A) available on the Documentation and Tools
CD-ROM packaged with your switch, or from www.alliedtelesyn.co.nz/
documentation/documentation.html.
■AT9800 Series Switches Documentation Set for Software Release 2.4.3
(Document Number C613-03044-00 Rev B) and Release Note for Software
Release 2.4.4 for SwitchBlade 4000 Switches and AT-9800 Series Switches
(Document Number C613-10342-00 Rev A) available on the
Documentation and Tools CD-ROM packaged with your switch, or from
www.alliedtelesyn.co.nz/documentation/documentation.html.
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
Table 1: Patch file details for Patch SB244-01.
Base Software Release File sb-244.rez
Patch Release Date 23-Oct-2002
Compressed Patch File Name sb244-01.paz
Compressed Patch File Size 84666 bytes
2Patch Release Note
Patch SB244-01 for Software Release 2.4.4
C613-10349-00 REV A
Features in SB244-01
Patch SB244-01 includes all issues resolved and enhancements released in
previous patches for Software Release 2.4.4, and the following enhancement:
When an interface went down (or was disabled) on an AS border router, the
external routes were not removed from the routing domain. Such routes are
now removed by premature aging.
The learning unit was locking under heavy load. This could result in pings
to a network device failing, and over an hour all dynamic MAC addresses
could be lost. Sometimes a large number of pause frames were generated by
the system. This issue has been resolved.
When an IP Multihomed interface was used as an OSPF interface,
neighbour relationships were only established if the IP interface for OSPF
was added first in the configuration. Now, OSPF establishes neighbour
relationships regardless of the IP Multihomed interface configuration order.
The SwitchBlade mirror port field on the second instance of a switch chip
was displaying as though it was the first instance. This issue has been
resolved.
The following issues have been resolved:
• IP route updating was not working correctly
• IGMP snooping behaviour was incorrect
• The SHOW DVMRP FORWARDING command displayed incorrect
port numbers.
DHCP RENEW request messages are now unicast (as defined in the RFC),
not broadcast.
After a prune lifetime had expired, the interface was not joined back to the
DVMRP multicast delivery tree. This issue has been resolved.
The following issues have been resolved:
• It was possible to assign the same network on different IPV6 interfaces
• The loopback address was being added to other interfaces
• The tunnel configuration was not showing correctly in IPV6
configuration commands
• RIPv6 now sets the metric of routes for interfaces that are DOWN to 16,
and immediately sends responses when the link status of VLAN
interfaces changes.
PCR: 01285 Module: OSPF Network affecting: No
PCR: 02353 Module: SWI Network affecting: No
PCR: 02359 Module: IPG Network affecting: No
PCR: 02361 Module: SWI Network affecting: No
PCR: 02394 Module: IPG, SWI, DVMRP Network affecting: No
PCR: 02396 Module: DHCP Network affecting: No
PCR: 02397 Module: DVMRP Network affecting: No
PCR: 02398 Module: IPV6 Network affecting: No
Patch SB244-01 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 3
Patch SB244-01 for Software Release 2.4.4
C613-10349-00 REV A
Neighbour discovery and PIM6 caused a fatal error when IPv6 was not
enabled, or when the IPv6 feature license was not present. This issue has
been resolved.
A Router-Alert option has been added. Also, the SHOW IPV6 MLD
INTERFACE command now works correctly.
ICMP was sending too many messages back as responses to fragmented
packets. This issue has been resolved.
A warning now appears when the DELETE IP INTERFACE command is
executed before the DELETE DVMRP INTERFACE command.
VRRP pre-empt mode was not working with advertisement updates of 1
second or more because this did not allow for interface start time on startup.
Now a check is made to verify that interfaces are UP before timers are
started.
Static IP ARP entries could not be added to hardware at boot time. Also, an
IPX circuit could not be deleted from hardware. These issues have been
resolved.
Multicasting forwarding was not working correctly. This issue has been
resolved.
The IGMP port list was not updating correctly when a port went down. This
issue has been resolved.
ICMPv6 was returning an error for non-zero fragment offsets. This issue has
been resolved.
Packets with a RIP source address and next hop address that are not on the
same subnet as the interface will now be processed. If the received next hop
is not on the same subnet, it is treated as 0.0.0.0.
On GBICs, the link was forced up when the transmit fibre was removed.
Once up, the link could not be taken down again by removing the transmit
fibre. This issue has been resolved.
PCR: 02401 Module: IPV6 Network affecting: No
PCR: 02406 Module: IPV6 Network affecting: No
PCR: 02407 Module: IPG Network affecting: No
PCR: 02409 Module: IPG Network affecting: No
PCR: 02410 Module: VRRP Network affecting: No
PCR: 02413 Module: IPG, IPX2 Network affecting: No
PCR: 02416 Module: DVMRP, IPG Network affecting: No
PCR: 02417 Module: VLAN, IPG Network affecting: No
PCR: 02418 Module: IPV6 Network affecting: No
PCR: 02415 Module: IPG Network affecting: No
PCR: 02420 Module: SWI Network affecting: No
4Patch Release Note
Patch SB244-01 for Software Release 2.4.4
C613-10349-00 REV A
IGMP messages sometimes caused a fatal error. This issue has been
resolved.
Multicast downstream groups are now added and deleted correctly.
Errata
AT-9800 Series Switches do not have Ethernet interfaces (for example, eth0).
Previously released documentation incorrectly states that these interface types
are valid. AT-9800 switch ports are Ethernet ports, and these are referenced in
commands with the PORT parameter.
IPSec and ISAKMP are not available on the 2.4.4 release for SwitchBlade 4000
Series Switches and AT-9800 Series Switches.
Availability
Patches can be downloaded from the Software Updates area of the Allied
Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html. A
licence or password is not required to use a patch.
PCR: 02423 Module: SWI Network affecting: No
PCR: 02425 Module: IPG Network affecting: No
Andere Allied Telesis Schalten Handbücher
Allied Telesis
Allied Telesis x950 Series Bedienungsanleitung
Allied Telesis
Allied Telesis AT-9000/24 Bedienungsanleitung
Allied Telesis
Allied Telesis AT-x230-10GP Bedienungsanleitung
Allied Telesis
Allied Telesis 48Ts/X Bedienungsanleitung
Allied Telesis
Allied Telesis AT-8100S/24C Bedienungsanleitung
Allied Telesis
Allied Telesis AT-8600 Series Bedienungsanleitung
Allied Telesis
Allied Telesis AT-GS950/48 Bedienungsanleitung
Allied Telesis
Allied Telesis AlliedWare Plus x530 Series Bedienungsanleitung
Allied Telesis
Allied Telesis AT-8600 Series Betriebsanleitung
Allied Telesis
Allied Telesis AT-FS709FC Bedienungsanleitung
Allied Telesis
Allied Telesis x330 Series Bedienungsanleitung
Allied Telesis
Allied Telesis x550 Series Bedienungsanleitung
Allied Telesis
Allied Telesis AT-FH708SW Bedienungsanleitung
Allied Telesis
Allied Telesis AT-x210-9GT Installationshandbuch
Allied Telesis
Allied Telesis Rapier 16fi Bedienungsanleitung
Allied Telesis
Allied Telesis AlliedWare Plus AT-x530-28GPXm Bedienungsanleitung
Allied Telesis
Allied Telesis x230-10GP Installationshandbuch
Allied Telesis
Allied Telesis AT X900-12XT/S Bedienungsanleitung
Allied Telesis
Allied Telesis AT-GS950 Bedienungsanleitung
Allied Telesis
Allied Telesis AT-RS710TX Bedienungsanleitung
