AllSee Technologies DV-LED Bedienungsanleitung

PG. 1

DV-LED Installation Guide

PG. 2

Pre-Setup

Parts List

Please read entire instruction sheet before you start.

Please consult with a trained electrician at least one day before installation to discuss the

power sources for the DV-LED video wall.

Please consult with your project manager for arrangements on where to house the external

sending card box and media player.

Tools: 1 x Screwdriver, 1 x Drill, 1 x Spirit Level, 1 x Magnetic Module Tool

As each DV-LED display is unique, these figures are based per cabinet/module

For each cabinet enclosure there should be;

•1 x Power Supply Cable

•1 x Network Cable

•6 x LED Modules

•5 x M8 Screws (pictured)

For each module there should be;

•8 x Magnetic Screws (pictured)

(8 Screws x 6 Modules = 48 screws per cabinet)

Based on your DV-LED configuration you should be able to calculate how many protective

edging pieces you need. There are two different sizes depending on whether the edging is

going on the top/bottom of the cabinet or the side.

PG. 3

Instructions

Step 1

Clear a space on the floor and lay the cabinets in the formation they will be going on

the wall. The cabinets should be facing up with the interior of the cabinet exposed.

Step 2

Within your layout, organise the cabinets into vertical columns and screw the cabinets

together vertically using two of the M8 screws for each cabinet as per the diagram

below.

Depending on the configuration of your DV-LED Video Wall you will be supplied with mounting

brackets either 1.2m in length or 1.8m in length. We do NOT supply screws for the mounting

bracket due to the various types of walls which the mounting brackets can be used upon.

For each 1.2m section of bracket we recommend of using 5-6 M8 screws as minimum.

For each 1.8m section of bracket we recommend of using 6-8 M8 screws as minimum.

PG. 4

Step 3

Once a vertical column is done, flip it over and attach the mounting bracket on the

backs of each cabinet that is needed to be hung.

Step 4

Next, attach the mounting brackets to the wall for the number of horizontal cabinets

you have. There are two lengths of mounting brackets available and you may need to

use a combination of both. The shorter 1.2m bracket can mount two cabinets wide and

the longer 1.8m bracket can mount 3 cabinets wide.

Step 5

Lift each cabinet column off the floor and onto the mounting brackets on the wall.

Secure with the screws provided.

Please note: This does NOT mean every cabinet needs a bracket. The rule

is one bracket for every 3 cabinets it supports. Please see the diagram

below for how this works.

PG. 5

Your DV-LED Video Wall should now look something like this.

Step 6

Attach each of the columns to its horizontal neighbour. Take this by take a cabinet and

secure it to the neighbor using 3 of the M8 screws provided as per the diagram.

PG. 6

Step 7

Working top to bottom in each vertical column use a CAT6 cable to attach the power

supplies from one cabinet to the next until you are left with the power supply cable

sticking out of each of the bottom cabinets. We recommend leaving about 3m-5m of

power cable coming out of the bottom cabinet.

Please note: If needed you can arrange the power cables so they go out

the top of the cabinets.

PG. 7

Step 8

Next take the data cable and working from the top right corner connect all the cabinets

using the RJ45 ports, you can use either port for in and out. You should connect them

like a snake, working vertically up and down and across each column until all the

cabinets are connected.

PG. 8

Step 9

Check around the outside of the cabinet, if there are any screws sticking out now is the

time to remove them from the inside of the cabinet. There are two different types of

screws that may need to be removed. To remove the screws on the sides of the

cabinets you may need to unscrew the stopper (circled in red).

Step 10

Take the modules out of the box and connect the magnetic screws. For each module

attach 8 screws, 4 along the top and 4 along the bottom.

Step 11

Attach the magnetic screws to the modules. For each module there should be 8 screws

attached along the top and bottom as in the diagram below. Now attach the modules

to the cabinets, for each module you need to connect a power cable and data cable,

Please note: You can do this by hand or by using a standard drill

PG. 9

the module should easily snap onto the magnetic screws. For each cabinet there

should be 6 modules.

Step 12

For a clean finish now attach the protective edging. You may need to temporarily pop

off some of the modules to secure the edging using the rivets provided. After the

edging is attached you can reattach the modules. Make sure you thread the power

cables/data cable through the protective edge as you attach the bottom sections of

edging.

Step 13

The final steps are to connect the loose cables. Connect each of the power cables in

the vertical columns to the power sources. Take the data cable and connect it to the

pre-configured sending box which should connect to the pre-configured media player.

Inhaltsverzeichnis

Andere AllSee Technologies Monitor Handbücher

AllSee Technologies

AllSee Technologies 32" High Definition Digital Advertising... Bedienungsanleitung

AllSee Technologies

AllSee Technologies PCAP Multi Touch Screen Display Bedienungsanleitung

AllSee Technologies

AllSee Technologies FR8A Bedienungsanleitung

AllSee Technologies

AllSee Technologies PF46HD-B Bedienungsanleitung

AllSee Technologies

AllSee Technologies Slimline Bedienungsanleitung

AllSee Technologies

AllSee Technologies TL H7 Series Bedienungsanleitung

AllSee Technologies

AllSee Technologies P2-B Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung