Allworx 6x Bedienungsanleitung

Page 1 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

How to Configure the Allworx 6x, 24x and 48x for use with Integra Telecom

SIP Solutions

Overview: This document provides a reference for configuration of the Allworx 6x IP PBX to connect to Integra

Telecom SIP Trunks. The document covers a basic setup with required stepsfor interoperability with Integra

Telecom only.

Hardware and Software: The following hardware and software were employed to test interoperability between

the Allworx IP PBX and Integra.

Manufacturer

Model

Software Version

Allworx

7.2.5.1

MetaSwitch

MetaSphere

7.2

Adtran

NV3305

17.09.02

Tested Features: The folowing is a list of features that were tested.

Feature

Description

Issue (if any)

Basic Call

Making and receiving a call between

the IP-PBX and Integra Telecom

service provider with both G.711

and G.729 codec.

None

Call Hold

Placing a call in On Hold state and

retreival of a call from same station.

None

Call Transfer

Relocation of an active call from one

station to another. Both internal

and external transfers were tested.

Transfer with SIP REFER (RFC 3515)

not currently supported.

Call Forward

Forwarding of calls from one station

to another.

Call Redirect method not currently

supported.

Remote Handset

Operation of a SIP handset from

remote network

None.

Fax

Fax Transmission

T.38 fax not supported on Allworx

6x. G.711 fax is supported.

Network Topology: Figure 1 shows how the network was configured for interoperability testing.

Page 2 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

Figure 1: interoperability network diagram

Configuration Notes: This section contains a detailed description of how the Allworx 6x was configured for

interoperability testing with Integra Telecom services.

Network Requirements: As in any VoIP deployment there must be adequate bandwidth to support VoIP

traffic. A proper network assessement should be performed before any VoIP deployment.

Assumptions:

All SIP Signalling uses UDP on port 5060.

SIP Signalling packets use Differentiated Services Code Point (DSCP) 24.

Real-Time Transport Protocol (RTP) uses DSCP 46.

Licenses: The Allworx Ip PBX must be equipped with licensing to support SIP Trunks.

DID Block Setup

1. Browse to Home >> Phone System >> Outside Lines. Click on “add new DID block”.

Page 3 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

2. Enter the “Starting Phone Number” and “Total number of phone numbers in DID Block” as

provided by the Integra implementation team. Select “make a new Routing Plan from the “DID

Routing Plan” pulldown and click “Update.

3. Configure “Phone Number to Extension Mapping” as required for your deployment.

SIP Proxy Setup

1. Browse to Home >> Phone System >> Outside Lines. Select “add new SIP Proxy.

2. Input Integra in the “Description” field. Input “User Name” and “Password” as provided by

the Integra implementation team. Populate the fields “SIP Server”, “Outbound Proxy” and

“Registrar” as provided by the Integra implementation team and “Port” with 5060. Input

the “Maximum Active Calls” as provided by the Integra implementation team.

Page 4 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

3. In Advanced Settings verify that “Enable Early Media” is checked, “Obtain DID/ DNIS number

from is set to SIP To: header field and “Use” _____ “in Request URI of outbound calls is set

to dialed number.

4. In the Call Route section, ensure that “Routed using DID Block(s)” is selected and check the

appropriate DID block(s) as previously defined in DID Block Setup.

5. In the Service Groups section click on “add new Service Group”.

Page 5 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

6. Enter Integra in the Description field. Select Integra from the list of Services and click Move

to add it to the Service Group.

7. Browse to Home >> Phone System >> Dial Plan. In the External Dialing Rules section click on

Modify.

8. Enter your Home area code and chose an appropriate Dial Method for your local calling

area. Select Integra from the Service Group pull down. Repeat these steps for as many area

codes that do not require dialing 1 for your local calling area, adding new rows as necessary.

For all others select Integra from the Service Group pull down.

Page 6 Integra Telecom –Allworx 6X/24X/48X

2/25/2011

Andere Handbücher für 6x

Dieses Handbuch passt für folgende Modelle

Andere Allworx Server Handbücher

Allworx

Allworx Allworx 10x Bedienungsanleitung

Allworx

Allworx Allworx 10x Bedienungsanleitung

Allworx

Allworx Allworx 10x Kurzanleitung

Allworx

Allworx 6x Bedienungsanleitung

Allworx

Allworx Allworx 10x Bedienungsanleitung

Allworx

Allworx Connect Series Bedienungsanleitung

Allworx

Allworx 6x Bedienungsanleitung

Allworx

Allworx Allworx 10x Montageanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung