Quick Installation Guide SNX-60x0-486F Series Data Center Switch
5
Attention: Un dispositif de déconnexion facilement
accessible doit être incorporé dans l'installation
électrique du bâtiment.
Caution: Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to
the instructions.
Attention: Risque d'explosion si la batterie est
remplacée par un type incorrect. Jetez les piles usagées
selon les instructions.
警告:如果更換不正確之電池型式會有爆炸的風險˙請依
製造商說明書處理用過之電池˙
Rack-mount Safety Precautions
For your protection, observe the following rack-
mount safety precautions when setting up your
equipment:
Elevated Operating Ambient - If installed in a closed
or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater
than room ambient. Therefore, consideration should be
given to installing the equipment in an environment
compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a
rack should be such that the amount of air flow
required for safe operation of the equipment is not
compromised.
Mechanical Loading - Mounting of the equipment in
the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
Circuit Overloading - Consideration should be given
to the connection of the equipment to the supply
circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply
wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing
this concern.
Reliable Earthing - Reliable earthing of rack-mounted
equipment should be maintained. Particular attention
should be given to supply connections other than
direct connections to the branch circuit (for example,
use of power strips).
For safety, equipment should always be loaded from
the bottom up. That is, install the equipment that will
be mounted in the lowest part of the rack first, then the
next higher systems, etc.
To prevent the rack from tipping during equipment
installation, the anti-tilt bar on the rack must be
deployed.
The mounting brackets provided must be used to
securely mount the device in a rack-mount unit.
Regulations & Warnings
FCC Warning
NOTE: This equipment has been tested and found to
comply with the limits for a class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment uses, generates, and can
radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause
interference in which case the user will be required to
correct the interference at his/her own expense.
WARNING: Changes or modifications made to this device
which are not expressly approved by the party responsible
for compliance could void the user’s authority to operate
the equipment.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
BSMI Notice
警告使用者: 此為甲類資訊技術設備，於居住的環境中使用
時，可能會造成射頻擾動，在此種情況下，使用者會被要求
採取某些適當的對策。
警告
此为 A级产品，在生活环境中，该产品可能会造成无线电干
扰。在这种情况下，可能需要用户对其干扰采取切实可行的
措施。
Safety Compliance
Warning: Class 1 Laser Product.
EN: When using a fiber optic media expansion module,
never look at the transmit laser while it is powered on.
Also, never look directly at the fiber TX port and fiber
cable ends when they are powered on.
FR: Ne regardez jamais le laser tant qu’il est sous
tension. Ne regardez jamais directement le port TX
(Tramsmission) à fibres optiques et les embouts de
câbles à fibres optiques tant qu’ils sont sous tension.
Warning: Class 1M Laser Product (Laser Radiation):.
EN: Class 1M laser radiation when open. Do not view
directly with optical instruments
