Alphatech IP BOLD65 series Bedienungsanleitung

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

IP BOLD65 quick setup guide

Firts steps before you start programming the unit

Warning: before you start working with the unit, please read instructions below to avoid losing the

warranty.

Item No. 230501 IP BOLD65 T1C Item No. 230502 IP BOLD65 T2C

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Thank you for purchasing the IP BOLD65 video doorphone.

Initially select your correct place of installation to achieve the best results. IP BOLD65 is designed to

be surface mounted. Before mounting the IP BOLD65, please check that the place of installation

meets the following requirements as shown at the Fig 1 below. Persons with an average height will be

displayed well on the screen of IP videophone or your computer screen if you install the camera at

160cm height above the ground. The camera should not be installed at places where the sun is shining

to the camera directly, where there is a very strong, intensive light source or where there are reflexive

materials used. This will cause a bad image quality.

Fig 1 Correct height of installation, camera should be installed at 160cm height above the ground level

Installation is done with four twist screws and four wall plugs.

Mounting plate –see Fig. 2 below.

Recommended:

- 4x wall plug with a diameter of 8mm

- 4x screw (a twist) with a half-round head. Diameter 5mm, length 35mm

!!! On the screws please use the supplied rubber rings for protection against water leakages !!!

We recommend the following surface mounting procedure:

- Open the front cover of the unit, disconnect the call buttons cable (point 22, Fig. 5 below)

- Use the supplied rubber bushing for all cables (ETH UTP cable, power supply adapter cable, relay

wires)

- Lead in the cables and wires through the rubber busing (see Fig. 8 below)

Fix the unit safely to the surface of the wall (use screws with wall plugs). Fix all 4 screw holes and do not

forget to use the rubber rings for screws to avoid water leakages.

- Be careful to provide enough space inside the wall behing the IP BOLD65 unit for the rubber bushing to

avoid damaging the rubber busing, jamming and damaging the cables, see Fig. 10 below

- Connect all the wires, see Fig. 13 and next Figures

- Close the top front cover of the unit, see Fig. 3 with the closed top front cover.

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Fig 2. IP BOLD65 mounting plate

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Before you connect the IP BOLD65 to your network, let´s make a few initial steps. On Fig 3 below

you can see the contents of the packing box.

Fig. 3 Contents of IP BOLD65 T2C packing. 4x wall plug, 4x twist screw with rubber rings, 1x rubber

bushing for leading in the cables and wires, 1x allen key. The IP BOLD65 unit is quite heavy, so

please place underneath the unit a protection (e.g. a paper cartoon box) to avoid damaging your table



ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Open the IP BOLD65 using the supplied allen key, see Fig 4 below. Open the top front cover slowly

and carefully. As you can see on the Fig 4 below, the call buttons are connected to the main board via

the yellow/white/green cable, so make sure you do not damage it. It is better to disconnect this call

buttons cable before you continue working the unit.

Fig 4 –Open your IP BOLD65 using a supplied allen key, make sure you do not damage the cable

connector, connection to the call buttons or the cable itself. It is better to disconnect the call buttons

cable.

If you unplug the call buttons cable from the connector (point 22 at Fig 5 below), it will be easier to

detach the front cover and work with the doorphone. Connector´s orientation is based on the colours of

the cable.

Fig 5 Unplug the call buttons cable (point 22) to detach the front cover easily.

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Slowly and carefully, unscrew the illuminated name/house number module using a cross head

screwdriver, see black arrows at Fig 6 below on the left side. Be careful, the illuminated module is

connected to the main board via a black cable, so unscrew and detach it slowly and carefully to avoid

damaging the connection cable, the cable connector or the illumimated info module. You can also

disconnect this cable to avoid damaging it, it will be easier to continue your work with the unit. Avoid

breaking the white/red cable leading to the microphone at the bottom part of the unit, see Fig 6 below.

Fig 6. Using a cross head screwdriver, detach the top illuminated info module carefully (name/house

number module). On the top front of the illuminated info module you can place your own label with

your name, a house number or your required information, see Fig 19 for more details on changing the

name plate.

To avoid water leakages into the unit, please make sure to use the rubber busing (Fig. 4 below) for

ETH UTP cable, power supply adapter cable and relays wiring.

Fig. 7 Apply rubber bushing to avoid water leakages into the unit

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Ethernet UTP cable, the power supply adapter cable and relay wires need to be lead through the IP67

rubber bushing, see Fig 8 below.

Fig 8. Use the rubber busing with IP67 impregnation rating to avoid any leakages inside the unit

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Use the IP67 rubber busing for leading the cables and wires inside the IP BOLD65 unit.

Fig 9. Use the IP67 rubber busing to avoid any leakages inside the unit

Use the IP67 rubber busing for leading the cables and wires inside the IP BOLD65 unit. Make sure it

is attached tightly to the housing, so the rubber busing does not fall back inside the unit.

Fig 10. Use the rubber busing with IP67 impregnation rating to avoid any leakages inside the unit.

Make sure there is enough space behing the unit inside the wall to avoid jamming the cables,

damaging the rubber busing and damaging the cables.

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Use the rubber busing to avoid any leakages inside the unit

Fig 11. Use the rubber busing to avoid any leakages inside the unit

ALPHATECH TECHNOLOGIES s.r.o.

Jeremenkova 88, Praha 4, Czech Republic

www.alphatechtechnologies.cz

141 00 Praha 4

Before closing the top front cover of the IP BOLD 65 unit, always use screws with rubber rings to

avoid any leakages inside the unit. There are 4 screws holes for 4 screws with rubber rings, two at the

top and two at the bottom of the unit. This ensures the unit is well attached/mounted to the surface of

the wall.

Fig 12. Use screws with rubber rings to avoid any leakages inside the unit

Dieses Handbuch passt für folgende Modelle

Andere Alphatech Gegensprechanlage Handbücher

Alphatech

Alphatech IP BOLD HW Leitfaden

Alphatech

Alphatech GSM-Variobell Bedienungsanleitung

Alphatech

Alphatech NUDV-01 Bedienungsanleitung

Alphatech

Alphatech Fermax PBX EXP Handbuch

Alphatech

Alphatech Brave Smyle-C Bedienungsanleitung

Alphatech

Alphatech NUDV-00 Montageanleitung

Alphatech

Alphatech A-Bell-C Fehlerbehebungshandbuch

Alphatech

Alphatech SlimDoorPhone - 01 Bedienungsanleitung

Alphatech

Alphatech IP BOLD 65 Bedienungsanleitung

Alphatech

Alphatech IP Bold series Montageanleitung

Alphatech

Alphatech IP-VarioBell IPVB-01 Bedienungsanleitung

Alphatech

Alphatech Fermax Cityline v2 Bedienungsanleitung

Alphatech

Alphatech NFTZ - 01 Bedienungsanleitung

Alphatech

Alphatech IPDPS-01C Bedienungsanleitung

Alphatech

Alphatech Brave series Fehlerbehebungshandbuch

Alphatech

Alphatech A-VarioBell Fehlerbehebungshandbuch

Alphatech

Alphatech IP-VarioBell Bedienungsanleitung

Alphatech

Alphatech FTZ123-D12 Bedienungsanleitung

Alphatech

Alphatech Slim IPDP - 01 Bedienungsanleitung

Alphatech

Alphatech IP Bell Bedienungsanleitung

Alphatech

Alphatech Slim IPDP - 01 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung