ALTAI MIS200P Bedienungsanleitung
1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
ALTAI MIS200P
Industrial 14-Gigabit-Port
Managed PoE Switch
______________________________________________
Quick Setup Guide
Version 1.1
2
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1. Introduction
Thank you for purchasing the Altai MIS200P product. This guide provides
instructions to install the product and set it up with minimal effort.
2. Package Content
•MIS200P Main Unit x 1 pc
•DC Terminal Block Connector x 1 pc
•35mm DIN-rail Mounting Kit x 1 pc
•RJ-45 to RS232 DB9 Console Cable x 1 pc
3
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Product Description
Altai MIS200P is an industrial-grade managed switch featuring eight 1GbE
PoE ports, two 1GbE copper ports and four 100/1000BASE-X SFP slots. The
switch, with a rugged IP40 metal case and an ultra-wide temperature range
from -40°C to 80°C, is designed to operate in harsh industrial environments
such as factory, warehouse, and container port.
The switch supports 802.3af/at Power over Ethernet, a system to transmit
electrical power up to 30 watts, along with data, to remote devices over
standard twisted-pair Ethernet cable. Each MIS200P has eight 1GbE P.S.E.
ports, with a total power budget of 240W.
The MIS200P supports the advanced ITU-T G.8032 ERPS (Ethernet Ring
Protection Switching) redundant ring technology and Spanning Tree
Protocols (STP/RSTP/MSTP) for enhancing the system reliability and uptime of
any industrial networks. In a ring topology, the recovery time of the data link
can be as low as 20 ms.
4
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
4. Feature Highlights
•Eight 10/100/1000BASE-T PoE RJ-45 ports with auto MDI/MDI-X function
•Two 10/100/1000BASE-T Copper RJ-45 ports with auto MDI/MDI-X function
•Four 100/1000BASE-X SFP slots
•IP 40 aluminum case
•DC redundant power input with polarity reverse protection
•DIN rail mount
•4 kV power and data port surge protection
•8 kV Ethernet ESD protection
•Support ERPS redundant ring technology with recovery time down to 20ms
•Support STP/RSTP/MSTP
•Support up to 255 VLAN groups and 4094 VLAN IDs
•Support IGMP snooping v1/v2
•Support 802.1X RADIUS user access authentication
•Support SSH, SSL, and SNMP v1/v2/v3 management
•Support status monitoring by AltaiGate or AltaiCare On Premises
5
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
5. Applications
Deployment Scenario 1
The MIS200P is specifically designed to work with Altai APs. A typical use case
is as an access switch for an outdoor site, where multiple APs and other
devices are co-located.
Power + Data over Ethernet
Cable to 802.3af/at PD
Data over Ethernet Cable
Fiber Optic Cable
48-57V DC
Access
Point
IP Camera
Industrial PC
LAN
ERPS Ring
MIS200P
AltaiCare/AltaiGate
IoT Gateway
6
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Deployment Scenario 2
With its anti-shock and anti-vibration capabilities, the switch can readily be
used in an RTG or AGV for connecting a Wi-Fi CPE such as A2x and VX200 to
VMT (Vehicle-Mounted Terminal) and Camera.
18-32V DC
Quay Crane
AGV
RTG
Mobility Applications in Container Terminal:
Vehicle-Mounted
Terminal
IP Camera
CPE
MIS200P
Access Point
7
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
6. Hardware Overview
Physical Dimensions
Front Panel
Back Panel
165 mm
A
C
E
F
G
B
I
D
H
J
8
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Top Panel
A: PoE Ports (G1-G8)
8 x 10/100/1000BASE-T RJ-45 ports for data and power transmission. Each port
can provide up to max. 30W of power for 802.3af/at-compatible PDs
(Powered Devices) such as IP cameras and access points. It is
recommended to use Cat. 5/5e/6 UTP (unshielded twisted pair) or STP
(shielded twisted pair) of Ethernet cables for the connection. Cable run can
be up to 100 meters. Below is the table about the cable specifications.
Cable Categories
Supported Ethernet Signal
Max. Length
Connector
Cat. 5 UTP/STP
10/100BASE-T
100 m (328 ft)
RJ-45
Cat. 5e UTP/STP
10/100/1000BASE-T
100 m (328 ft)
RJ-45
Cat. 6 UTP/STP
10/100/1000BASE-T
100 m (328 ft)
RJ-45
Two wiring standards can be used for a RJ-45 connector: T568A or T568B. The
latter one is preferable for new networks. For details of pin assignments of
T568A/T568B wiring specifications, see Appendix A and B.
K
M
L
9
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
MIS200P switch also supports auto MDI/MDI-X operation. Therefore, you can
use either straight-through or crossover cables to connect the switch with
any other network devices. For simplicity, it is recommended to use straight-
through cables. For details of wiring for a straight-through or crossover cable
using T568B specification, see Appendix C and D.
Each port comes with two LEDs: Link and PoE to show its working status. For
details, see Section F and Grespectively.
B: Copper Ports (G9-G10)
2 extra ports of 10/100/1000BASE-T RJ-45 type for data transmission. The
connection is the same as to the PoE ports (G1-G8). It is recommended to
use the following types of Ethernet cable for the connection. Cable run is up
to 100 meters.
•Cat. 5/5e/6
•UTP/STP
•T568B wiring standard
•straight-through type
Each port comes with two LEDs: 100 and 1000 to show the Ethernet speed.
For details, see Section H.
10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
C: SFP Slots (G11-G14)
2 x 100/1000BASE-X SFP/mini-GBIC slots for fiber-optic cable connection of
either multi-mode or single-mode types.
SFP transceivers are hot-pluggable and hot-swappable. Therefore, you can
plug in and out the transceiver to/from the SFP slot without having to power
down the switch.
Before making the connection, make sure the SFP transceivers are of the
same media type on both sides, e.g. 1000BASE-SX to 1000BASE-SX, 1000BASE-
LX to 1000BASE-LX.
Also, check whether the fiber-optic cable type matches with the SFP
transceiver requirement, e.g. single-mode or multi-mode, connector types.
Note: SFP transceiver modules are not included in the package.
SFP Transceiver
Inhaltsverzeichnis
