Altec Lansing TimeMachine IMW465 Bedienungsanleitung

Item # IMW465

Owner’s Manual

Introduction

Thank you for purchasing the Altec Lansing timeMachine Wireless Alarm Clock Speaker, item IMW465. You

can use this speaker to listen to audio wirelessly from devices such as smart phones, iPods, tablets and most

other Bluetooth sound sources. This speaker can also be used to charge devices typically charged through a

computer’s USB port. Please read this manual carefully FIRST in order to get the most out of your speaker.

Package Contents

1. IMW465 timeMachine Bluetooth Alarm Clock

2. AC Adapter

3. 3.5mm Auxiliary Cable

4. Owner’s Manual with Warranty Information

Technical Specifications

- AC Adaptor: 10V, 2.4A

- Power Adapter Input Rating: 100~240V, ~50/60Hz 1.0A

Getting Started

Before you begin using your timeMachine Wireless Alarm Clock Speaker, you must make sure to connect it to

a power supply. Connect one end of the included AC adaptor (10V 2.4A) to the DC jack located on the back

of your unit. Connect the other end into a suitable power outlet in your home.

Setting the Correct Time

In order to use your device as an alarm clock, you will need to make sure it is set to display the correct time.

To do so, follow the steps below.

1. Press and hold the TIME SET button for 2 seconds until the clock’s display begins to flash.

2. Press the + or –buttons to alternate between the 12H setting (standard time) or the 24H (military

time) setting.

3. Press the TIME SET Button again to enter the clock setting mode and bring up the clock hours

4. Press the + or –Buttons again to adjust the clock hours to the current time (hold for rapid

setting).

5. Press the Time Set Button again to bring up the clock minutes.

6. Press the + or –Buttons againto adjust the clock minutes to the current time (hold for rapid

setting).

7. Press the TIME SET button to confirm the time and exit clock setting mode.

8. Congratulations! You have successfully set the time.

Notes: setting the clock must be on standby mode.

Using the FM Radio Function

Your device can play music from various audio sources, but it can also be used as an FM radio. To do so,

follow the steps below.

1. Press the POWER button to turn on your device.

2. Press the MODE button repeatedly to toggle through the various modes. To use your device as an FM

radio, make sure that FM displays on the screen along with the radio station that you are tuned in to.

3. Press the + or –buttons to tune the radio to a desired station. Hold either of these buttons for 2

seconds to search for the next clear station. Extend the attached antenna for best reception.

4. Press the VOL + or VOL- buttons to adjust the volume.

5. When you are through listening, press the POWER button to turn off your device.

Setting Up and Using FM Presets

Your device allows you to store up to 20 FM radio station presets so that you have quick access to your

favorite stations. Follow the steps below to set and access your preset stations.

1. Press the MODE button repeatedly until the current FM radio station appears on the display screen.

2. Press the + or –buttons to tune the radio to a desired station. Hold either of these buttons for 2

seconds to search for the next clear station.

3. Press and hold the PRESET button for two seconds until the preset number begins to flash on the display

screen.

4. Press the + or –buttons to selects the preset number you wish to set.

5. Press and release the PRESET button to confirm. Repeat steps 2 -5 until you have set up all 20 preset

stations.

6. To listen to a preset FM station at any time, press the MODE button repeatedly until the current FM radio

station appears on the display screen. Then press the PRESET button repeatedly to cycle to the desired

preset.

Setting Up the Alarms

Your device can also be used as an alarm clock, with two separate alarms that can each be set. Read the

steps below for an explanation of how to set alarm 1. To set alarm 2, follow the same steps using the AL2

button.

1. Press and hold the AL1 button for 2 seconds until the alarm time flashes onthe display screen.

2. Press the + or –Buttons again to adjust the desired alarm clock hours (hold for rapid setting).

3. Press the AL1 Button again to bring up the clock minutes.

4. Press the + or –Buttons again to adjust the desired alarm clock minutes (hold for rapid setting).

5. Press the AL1 button to confirm the alarm time setting. Next youcanchoose which audio source will be

used as the alarm sounds.

6. Press the + or –buttons repeatedly to select a desired audio source for the alarm. You can

choose amongst the following options: bb (buzzer), bt (Bluetooth) or RADIO (FM radio).

bt:You will wake to the currently linked Bluetooth device. If no device is detected, the default buzzer will sound instead.

Radio: Press the + or –buttons to tune the radio to the station you’d like to wake up to before turn off the unit.

bb:You will wake to the buzzer alarm.

7. Press the AL1 button to confirm which audio source will be used as the alarm sounds. Next, the alarm

volume display will flash. Press the + or –buttons to increase or decrease the alarm volume setting.

Press the AL1 button to confirm. The alarm icon will remain on the display screen, indicating the alarm is set.

Notes: setting the alarm clock must be on standby mode.

Turning the Alarms ON or OFF

Once you have setup your alarm, you can choose to turn it on or off.

1. Press and release the AL1 or AL2 button as needed to alarm 1 or alarm 2 ON and OFF. You will see an

alarm icon appear on the display screen to indicate when the alarm is turned on. This icon will disappear when

the alarm is turned off.

Snooze/Dimmer Button Functions

When the alarm is going off, you can use the snooze function to temporarily quiet the alarm so that you can

have some extra rest. The dimmer button increases or decreases the brightness of your display screen.

1. When the alarm is sounding, press the SNOOZE/DIMMER button to temporarily silence the alarm. By

default, the alarm is silenced for 9 minutes. Snooze can be used repeatedly as the alarm continues to sound.

Touchless Snooze Control

You can also activate the snooze feature without physically touching the SNOOZE/DIMMER button. To do so,

simply place your hand near the front panel display screen of your device. The front panel has a built in wave

sensor which works by detecting body heat. For best results, your hand should be within 24 inches of the front

panel display screen to activate Touchless Snooze Control.

2. To adjust the brightness of the display screen, press the SNOOZE/DIMMER button during normal operation

(when no alarm is sounding) to cycle through the brightness display settings.

Sleep Mode and Nap Modes

While listening to an audio source, you can program your device to power off after a set amount of time.

1. To choose what duration of time should pass before your unit powers off, press the TIME SET button while

audio is playing. Press the TIME SET button repeatedly to choose a duration of either 120, 90, 60, 45, 30, 20,

10 or 5 minutes or 00 (OFF) until your unit powers off.

2. To set Nap time, press and hold the MODE Button then press MODE Button again as needed to cycle to the

desired nap duration: 120, 90, 60,45, 30, 20, 10 or 5 minutes or 00 (OFF) (turns the nap alarm off).

Using the AUX-In Jack to Listen to Audio

You can use your device to listen to a Bluetooth audio source, or you can connect an audio source directly to

your device via the Aux-In jack.

1. Connect one end of a standard 3.5mm audio cable into the aux-in jack on the rear of your device. Connect

the other end into the headphone or output jack of your audio device.

2. Press the POWER button on the unit to power it on.

3. Press the MODE button repeatedly until the AUX icon appears on the display screen.

4. Press the VOL + or VOL- buttons to adjust the volume.

5. When done listening, press the POWER button to turn the unit off. Remember to turn off your audio device,

as well to avoid wasting battery power.

Charging Devices Using the USB Ports

This speaker can be used to charge devices typically charged through a computer’s USB port. To do so, follow

the steps below.

1. Connect the standard size end of a USB cable (not included) to the USB Port on back of the unit and

connect the other end to the charging port on your device.

2. Monitor the charging on your device. Some devices use a proprietary charging method and will not charge

using the USB Port. If this happens, you must charge your device using the charger that came with it.

NOTE: Your speaker must be plugged in to a working outlet in order to charge devices

Using Your IMW465 Speaker (Mono) with a Bluetooth Audio Source

You can use this speaker to listen to audio wirelessly from devices such as smart phones, iPods, tablets and

most other Bluetooth sound sources.

1. Press the POWER button to power on your speaker.

2. Press the MODE button repeatedly until the bt icon appears on the display screen. You will audibly hear

your speaker say, “You are now pairing.” LED will start blinking Blue. Now you are ready to pair your Bluetooth

device with your IMW465 speaker.

NOTES

-If you see the LED blinks Green instead of Blue. Press and hold the “TWS” button on the rear cabinet for 1

second to change the Bluetooth mode until the “bt” appears on the display and you hear “You are now pairing.”

Also LED will start blink BLUE. Now youcan ready to pair your device with IMW465.

3, Follow the instruction of your phone or other Bluetooth device to pair the unit.

a) Go to the Bluetooth Manager of your Bluetooth device.

b) Search Bluetooth devices and select “IMW465”to start connecting.

c) Enter “0000” if your device asks for a PIN code.

d) Once paired, the unit will beep and the Bluetooth icon on the LCD will turn on steady.

e) Although the unit can only stream audio from one device at a time.

When there is an incoming call:

1. Press the PRESET button to pick up the call.

To Disconnect Your Bluetooth Device

Turn off the connected device or press and hold “Play/ Pause” button to disconnect and refresh the connection

of Bluetooth device.

Reconnecting Your Device

To regain Single speaker mode, press “Play/ Pause” button for 3 seconds on the speaker, wait approximately

15 seconds. The “IMW465” speaker will automatically reconnect to previously connected your phone or

Bluetooth device. If you move out of range or turn off the Bluetooth feature on your device, the unit will

disconnect from your device. To reconnect, simply access the Bluetooth Manager on your device and select

IMW465.

Out of Range or Lost Signal

If your Bluetooth device is out of range (beyond 30 feet) of your speaker or if there is something blocking the

Bluetooth signal, the Bluetooth connection with the Bluetooth device may be lost.

To avoid a lost connection:

1. Move the Bluetooth device back into range of your speaker (within 30 feet), and/or make sure there’s a clear

line of sight between the unit and the Bluetooth device.

2. If the connection is lost, the connection will need to be reestablished. Follow the directions under

“Reconnecting Your Device”.

Inhaltsverzeichnis

Andere Altec Lansing Sprecher Handbücher

Altec Lansing

Altec Lansing MINI LIFEJACKET Bedienungsanleitung

Altec Lansing

Altec Lansing 802D HF DRIVERS Bedienungsanleitung

Altec Lansing

Altec Lansing 932-8B SPEAKER SYSTEM Bedienungsanleitung

Altec Lansing

Altec Lansing 604-8G - NETWORKSCHEMATIC Bedienungsanleitung

Altec Lansing

Altec Lansing IMA699 Bedienungsanleitung

Altec Lansing

Altec Lansing 14 HI FI SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing 405-8H Bedienungsanleitung

Altec Lansing

Altec Lansing 601C DUPLEX SPEAKERS Bedienungsanleitung

Altec Lansing

Altec Lansing CF108-4T Bedienungsanleitung

Altec Lansing

Altec Lansing DTS945A-F SPEAKER SYSTEM Bedienungsanleitung

Altec Lansing

Altec Lansing VS2320 Bedienungsanleitung

Altec Lansing

Altec Lansing SoundRover 50 Bedienungsanleitung

Altec Lansing

Altec Lansing Duplex DTS645-8AF Bedienungsanleitung

Altec Lansing

Altec Lansing ACS56 Bedienungsanleitung

Altec Lansing

Altec Lansing Baby Boom XL Bedienungsanleitung

Altec Lansing

Altec Lansing EXPRESSIONIST CLASSIC - Montageanleitung

Altec Lansing

Altec Lansing 401B CEILING SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing LF115-8A LF SPEAKER SYSTEM Benutzerhandbuch

Altec Lansing

Altec Lansing CD408-16T Bedienungsanleitung

Altec Lansing

Altec Lansing 399-8A 16A HF DRIVER Benutzerhandbuch

Altec Lansing

Altec Lansing 409T CEILING SPEAKER Bedienungsanleitung

Altec Lansing

Altec Lansing 5382A 5384A 5383A 5385A CEILING SPEAKERS Bedienungsanleitung

Altec Lansing

Altec Lansing DTS SPEAKER SYSTEM PRODUCT MATRIX Bedienungsanleitung

Altec Lansing

Altec Lansing 19 HI FI SPEAKER Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung

Altec Lansing timeMachine IMW465 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken