Altice UBC1326AA00 Bedienungsanleitung

UBC1326AA00

DOCSIS 3.1

Wireless eMTA

Quick

Installation

Guide

UBC1326AA00

D3.1 Wireless eMTA

Quick Installation Guide

Subscriber

Grounding the Device: Install the cable modem to include

grounding the coaxial cable to the earth as close as practical to

the building entrance per ANSI/NFPA 70 and the National

Electrical Code (NEC, in particular, Section 820.93, Grounding of

the Outer Conductive Shield of a Coaxial Cable). The device is

designed for IT power systems with phase-to-phase voltage at

120V.

This unit requires a 100-240V, 50/60Hz power adapter. The

power adapter must be keyed for proper polarization, and must

be fully inserted to contact the back of the power connector

port to ensure snug connection. Do NOT use any other power

adapter.

Disconnecting the Device: If the cable modem becomes

damaged or encounters some other abnormality, disconnect the

power plug from the AC wall outlet immediately.

Temperature and Altitude: Install the device in a location not to

exceed the maximum temperature of 104°F (40°C). Regular

operating altitude is 2000 m, and maximum operating altitude

is 4500 m.

•SAFETY NOTICES

•PREPARING FOR INSTALLATION

✓Locate the RF (coaxial) cable connector on the wall.

✓Verify the power outlet is working and is wired correctly.

✓Place your cable modem within a proper distance from the

outlet.

To connect a modem and a television to the same wall outlet,

you must use a cable line splitter (not included).

2. Connect an Ethernet cable (supplied) to one of the LAN

(Ethernet) ports on the back panel of the modem and connect

the other end to the Ethernet port of a computer. Use a

Category 5e or Category 6 Ethernet cable with RJ-45

connectors to ensure Gigabit Ethernet speeds (when the

computer supports it).

3. Connect an RJ-11 phone cable (not supplied) to the TEL

(telephone) port on the modem (when provisioned for voice

service as speciﬁed by the service provider), and connect the

other end to the phone port of the telephone. If voice service

is not provisioned through the service provider, telephone

service is not available.

4. Connect the power adapter (supplied) to the PWR (power)

port. Connect the other end to a power outlet.

UBC1326AA00

Wireless Voice Gateway

RJ-45

Analog Phone

RJ-11

Cable/RF

Device must be installed

vertically using the included leg

stands to obtain optimum

wireless performance.

Connect computers or Ethernet enabled

devices (wireless switch or router). A PC

should be connected for initial device

installation and configuration.

1. Connect the included leg stands to the bottom of the device

to enable the modem to be installed vertically. Connect the

coaxial cable (not supplied) to the DS/US (cable) connector

on the rear panel of the modem and connect the other end to

the cable wall outlet. Do not bend or over tighten the cable,

as this may strain the connector and cause damage.

•INSTALLING THE UBC1326AA00

•DEVICE WALL MOUNT INSTRUCTIONS

Label

Millimeters

(mm)

7.2 +/- 0.5

2.6 +/- 0.15

19.0 +/- 1.2

3~4

UBC1326AA00 Quick Installation Guide

5. Separate the wall mounting pieces. Mount the top and

bottom leg stand pieces (Figure 1) onto the UBC1326AA00

as shown in Figure 2.

6. You can now mount the UBC1326AA00 onto the wall using

the screws installed in Step 4.

2. Fit the 2 leg stand pieces

together with the wall mount

template as represented in the

graphic to the right.

3. Place this on the wall and use it

as a template to mark the wall

for the appropriate placement

of the screws.

4. Install the 4 screws on the wall

(158 mm or 6.2 inches apart).

NOTE: The screws should protrude

from the wall so you can ﬁt the

device between the head of the

screws and the wall. If you install

the screws in drywall, use hollow

wall anchors to ensure the unit

does not pull away from the wall

due to prolonged strain from the

cable and power connectors.

You can mount the UBC1326AA00 on a wall by following the

steps below:

1. You will need 4 round or pan head screws with the following

measurements:

Figure 1

Figure 2

•FEDERAL COMMUNICATION COMMISSION

(FCC) INTERFERENCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment oﬀand on, the user is encouraged to try

to correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

receiver.

•Connect the equipment into an outlet on a circuit diﬀerent

from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician

for help.

UBC1326AA00 Quick Installation Guide

5GHz Wireless Statement:

For operation within the 5.15~5.25GHz and 5.47~5.725GHz

frequency ranges, this device is restricted to indoor

environments.

This device meets all the other requirements speciﬁed in Part

15E, Section 15.407 of the FCC Rules.

FCC Caution:

Any changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user's authority

to operate this equipment.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 30 cm between

the radiator & your body.

This reminder is provided to call the CATV systems installer's

attention to section 820-93 of the National Electric Code, which

provides guidelines for proper grounding and in particular,

specify that the Coaxial cable shield shall be connected to

grounding system of the building, as close to the point of cable

entry as practical.

•NOTE TO CATV INSTALLER

Andere Altice Modem Handbücher

Altice

Altice UBC1319AA00 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung