Altinex PNP517C Bedienungsanleitung
0"
Document p/n:
250-0858-003
Page 1 of 4
1. STOP 2. MEASURE 3. CUT
1. STOP 2. MEASURE 3. CUT
4
MEASURE ITH A RULER.
DO NOT DAMAGE OR THRO A AY
THIS PORTION. THIS IS TOP COVER.
DO NOT SCALE OR ADJUST!
ALTINEX, INC. IS NOT RESPONSIBLE
FOR ANY DAMAGE TO A TABLE OR DESK.
2" 3"1"0"
MEASURE ITH A RULER.
87654320 1
cm. 4"
VERIFY ALL DIMENSIONS
TO ENSURE THAT THIS
PRINT IS 1 TO 1 SCALE.
109
!
R
cm.
inch.
0"
01 2
1"
3
PNP515
ALTINEX, INC.
MODEL NUMBERS:
2"
56
3"
7 8
1087 9643 52
4"2"1" 3"
10
4"
9
0 1
cm.
MEASURE ITH A RULER.
MIN. FINISHED
CLEARANCE
FINISHED CUT-OUT
DIMENSION
FINISHED CUT-OUT
DIMENSION FRONT FRONT
Take the top cover out of the packaging bag
and install it on top portion of the unit.
Do not install with screws yet, wait til step6.
Secure the mounting panel with unit under the table
using provided screws 3/4" long. Use screws
as specified on labels in the plastic bags
provided in the kit. The mounting screws
that are provided with the unit
should not be used on tables less than
3/4" thick.
Once the initial cut out has been made to the table,
use metal template provided by Altinex to find the
location of the pilot holes. Mark the location with
a fine marker or pen.
Pre drill pilot holes 10 times in the marked
locations for a #6 wood screw
(leave extra holes incase needed in the future use):
softwood Ø1/16",
hardwood Ø5/64"
The pilot holes should be
around .375" inches deep.
ALTINEX, INC. IS NOT RESPONSI LE
FOR ANY DAMAGE TO A TA LE OR DESK.
R
Document p/n:
250-0858-003
Page 2 of 4
(provided w/unit)
Document p/n:
250-0858-003
Page 3 of 4
R
Close unit.
Remove top protection
layer of both adhesive strips.
Place the wooden cover
over the top cover with
adhesive strips.
Align the wooden cover so that
the space around the wooden
cover is symmetrical. If the space
is not equal from first try, peel
the wooden cover off and try
again, untill it is aligned perfectly.
Once the wooden cover is aligned
push on it so that the unit opens,
pic -up the wooden cover along
with the stuc top cover plate and
mount both parts together. Pre-drill
pilot holes 4 times in the hole
locations for a #6 wood screw:
softwood Ø1/16",
hardwood Ø5/64"
The pilot holes should be
approx. .375" deep.
Use provided 1/2" screws to
mount the wooden cover to
the top cover panel. Then ma e
sure the unit is up and secure the
top cover to the unit using
under-cut screws provided
by Altinex.
(provided w/unit)
(provided w/unit)
To adjust and align the unit to the surface of the table, simply:
1. Close the unit. 2. Loosen all four wing nuts under the table.
3. ress the unit down or upwards from below the desk until it
aligns with the surface of the desk. 4. And tighten the wing
nuts below the desk.
R
Document p/n:
250-0858-003
Page 4 of 4
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Altinex Stromverteilungseinheit Handbücher
