Alto Professional Uber Bedienungsanleitung

User Guide

English ( 2 – 7 )

Guía del usuario

Español ( 8 – 13 )

Guide d’utilisation

Français ( 14 – 19 )

Guida per l’uso

Italiano ( 20 – 25 )

Benutzerhandbuch

Deutsch ( 26 – 31 )

Gebruikershandleiding

Nederlands ( 32 – 37 )

Appendix

English ( 38 – 39 )

User Guide (English)

Introduction

Thank you for purchasing the Uber PA. At Alto Professional, performance and reliability mean

as much to us as they do to you. That’s why we design our equipment with only one thing in

mind—to make your performance the best it can be. Questions, comments, suggestions? Let

us know at altoprofessional.com/support or on Facebook™. We’d love to hear from you.

Box Contents

Uber PA

Power Cable

User Guide

Safety & Warranty Manual

Support

For the latest information about this product (system requirements, compatibility information,

etc.) and product registration, visit altoprofessional.com.

For additional product support, visit altoprofessional.com/support.

Rechargeable Batteries

Rechargeable lead-acid batteries are the same type used in automobiles. As with your car

battery, how you use this battery has a significant impact on its lifespan. With proper use and

treatment, a lead-acid battery can last for years. Here are some recommendations for getting

the longest life from the internal battery.

General

Usage

Fully charge the battery before using the speaker.

Charge the battery completely after each use.

Storage For best product longevity, do not store at exceedingly hot (greater than

90 °F / 32 °C) or exceedingly cold (less than 32 °F / 0 °C) temperatures.

It is acceptable to leave your speaker plugged in. This will not overcharge the

battery.

If you leave the battery level low and do not charge it for 6 months, it may

permanently lose capacity.

Repair If the battery fails to charge, contact Alto Professional at altoprofessional.com.

Disposal Bring the unit to a recycling center or dispose of in accordance with local

ordinances.

Important Safety Precautions

Please note: Alto Professional and inMusic are not responsible for the use of its products or the

misuse of this information for any purpose. Alto Professional and inMusic are not responsible

for the misuse of its products caused by avoiding compliance with inspection and maintenance

procedures. Please also refer to the included safety and warranty manual for more information.

Caution: To reduce the risk of electric shock, do not connect Uber to a power outlet

while the grille is removed.

Stand-Mounting

•Always install loudspeakers in accordance with applicable electrical and building codes.

•Install the loudspeaker according to its maximum weight. Check the specifications of your

stand or pole to ensure it can support the loudspeaker’s weight. Also, observe all safety

precautions specified by the manufacturer.

•Do not mount multiple loudspeakers on the same stand or pole.

•Always verify that the stand or pole is on a flat, level, and stable surface. Also, fully extend

the legs of tripod-style stands, and ensure its legs do not present a trip hazard.

•Inspect the stand (or pole and associated hardware) before each use and do not use

equipment with worn, damaged, or missing parts.

•Always be cautious in windy, outdoor conditions. You may need to place additional weight

(e.g., sandbags) on stand’s base to improve stability. Do not attach banners or similar

items to any part of a loudspeaker system. Such attachments could act as a sail and

topple the system.

•Unless you are confident that you can handle the loudspeaker’s weight, ask another

person to help you lift it onto the stand or pole.

•Make sure your cables are out of the way of performers, production crew, and audience so

they will not trip over them, pulling the loudspeaker off the stand or pole.

Sound Level

Permanent hearing loss may be caused

by exposure to extremely high noise

levels. The U.S. Occupational Safety and

Health Administration (OSHA) has

specified permissible exposures to

certain noise levels. According to OSHA,

exposure to high sound pressure levels

(SPL) in excess of these limits may result

in hearing loss. When using equipment

capable of generating high SPL, use

hearing protection while such equipment

is under operation.

Hours per da

SPL (dB)Example

8 90 Small gig

6 92 Train

4 95 Subway train

3 97 High-level desktop monitors

2 100 Classical music concert

1.5 102 Riveting machine

1 105 Machine factory

0.5 110 Airport

0.25 or less 115 Rock concert

Setup

1. Make sure all items listed in the Box Contents are included in the box.

2. Read the Safety & Warranty Manual before using the product.

3. Make sure that you have completely charged the battery prior to first use for maximum

battery life.

4. Turn down the Master Volume on Uber.

5. Power on Uber.

6. Connect your devices.

7. Switch everything on in the following order:

•audio input sources (i.e. microphones, instruments, CD/MP3 Players)

•Uber PA

8. Raise the volume to a comfortable level.

9. Return the Master Volume to zero and turn off Uber when you are finished.

Example

Items not listed under Introduction >Box Contents are sold separately.

Bluetooth Device

Microphone

Tablet, MP3

Player, etc.

Guitar

Power

Features

Front Panel

1. Combo Inputs with Volume Control: Use a standard 1/4" (6.35 mm) TRS or XLR cable

(not included) to connect your sound source to each input. Use the Volume knob to adjust

the level of each one.

2. Line/Mic Switch: Use this switch to set the Input to accept either a Line-level or Mic-level

sound source.

Note: When using an instrument with passive pickups, set the switch to the Mic setting.

When using an instrument with active pickups, set the switch to the Line setting.

3. Bluetooth®:The Bluetooth LED will be lit when a device is paired to Uber. This LED will

not be lit when Uber is first powered on (unless it was previously paired with a device).

Press the Bluetooth button to disconnect a paired Bluetooth device.

4. Auxiliary Input with Volume Control: This stereo 1/8” (3.5 mm) input can be used to

connect a CD player, MP3 player, or other audio source. The Volume control adjusts

auxiliary input and Bluetooth volume.

5. Master Volume Control: This adjusts the loudspeaker's main mix volume, which includes

Instrument/Microphone Inputs, Auxiliary Input, and the audio of a paired Bluetooth device.

6. Line Out: Use a standard 1/4" (6.35 mm) TRS cable (not included) to connect this output

to the input of another loudspeaker. The Line Out is post-Master Volume Control.

7. USB Charging Port: Connect your device’s charge cable here to charge it. USB charging

only functions when the unit’s power is turned on.

Note: To charge smartphones and tablets faster, put the device’s screen to sleep.

8. Power Switch: Use this switch to power the loudspeaker on or off. Make sure all Volume

knobs are set to "zero" before powering it on. When the loudspeaker is powered on, the

Power LED above it will be lit.

9. Charge Indicator: This LED will illuminate when Uber is connected to AC power to

indicate it is charging. Once charging is complete, the LED will go off.

10. Battery Level Indicator: While the unit is powered on, these four lights indicate the power

left in the battery. Battery life varies based on volume and usage.

11. Power Cable Input (rear panel):Insert the included power cable here to charge the unit.

Please note that when the power cable is connected, the battery will still charge while the

unit is in use.

12. NFC (Near-Field Communication) (top panel):Touch and briefly hold your supported and

enabled device to the NFC logo to pair the device. See Pairing a Bluetooth Device Using

NFC for more information.

Operation

Pairing a Bluetooth®Device

1. Turn on your Bluetooth device.

2. Turn on Uber using the power switch. If you have previously connected to another

Bluetooth device, Uber will reconnect.

3. Navigate to your Bluetooth device’s setup screen, find Uber and connect.

Note: If your device requires a passcode or PIN, enter 0000.

4. The Bluetooth LED will light up solid when it is "paired."

If your Bluetooth device is not able to connect to Uber, press the Bluetooth button on

Uber to break previous Bluetooth connections and reset the Bluetooth module.

5. Start playback from your Bluetooth device.

6. To disconnect a connected Bluetooth device and connect to another Bluetooth device,

press the Bluetooth button. Repeat Step 3.

Note: If you experience trouble connecting or playing music, update your device's OS.

Pairing a Bluetooth Device Using NFC

NFC (near-field communication) allows data exchange from devices, such as pairing, by gently

bumping them together. Check in your device’s manual to see if this feature is supported.

To use NFC to pair with Uber:

1. In order to use NFC, your device must be turned on and unlocked.

2. Enter your device’s Settings menu and check that NFC is turned On (one-time step).

3. Power on Uber.

4. Touch and briefly hold your device to the NFC logo located on Uber’s top panel.

5. Follow the pairing instructions that appear on your phone. If a passcode is required, enter

“0000”.

6. To unpair, gently bump your device against the NFC logo.

Using the Aux Input

Connect your smartphone, MP3 player, or similar device to the Aux Input. Adjust the output

volume on your source device and then adjust the overall volume using the Aux Input Volume

Control on Uber.

Troubleshooting

If the sound is distorted: Try lowering the volume control of your sound source, musical

instrument, or microphone. Also, try to reduce the overall volume of Uber using the Master

Volume knob.

If there is too much bass: Try adjusting the tone or EQ control on your sound source to lower

the bass level. This will allow you to play the music louder before clipping (distortion) occurs.

If there is a high-pitched whistling noise when using microphones: This is probably

feedback. Point the microphone away from the speaker.

If you can’t hear the microphone over the music volume: Turn down the music volume

from your source.

If you can't hear your instrument: Check the setting of the Line/Mic switch. If you are using

an instrument with passive pickups, set the switch to the Mic setting.

If you can’t play music from a flash drive: The USB port is only for charging USB devices.

RF Exposure Information

Maximum RF Power: Bluetooth (2402–2480 MHz): 5.32 dBm

The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20

cm between the device and the human body. To maintain compliance with RF exposure

requirement, use product that maintain a 20 cm distance between the device and human body.

Regulatory Conformance

Hereby, inMusic Brands, Inc. declares that the radio equipment type (ÜBER battery-

powered performance PA) is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following Internet address:

altoprofessional.com/safety

Notice: Observe the national local regulations in the location where the device is to be used. This

device may be restricted for use in some or all member states of the European Union (EU).

Guía del usuario (Español)

Introducción

Gracias por comprar el Uber PA. En Alto Professional, el rendimiento y la confiabilidad

significan tanto para nosotros como para usted. Por eso es que diseñamos nuestros equipos

con una sola cosa en mente—hacer que pueda tocar su mejor interpretación.

¿Preguntas, comentarios, sugerencias? Envíelas a altoprofessional.com/support o mediante

Facebook™. Nos encantaría escucharlas.

Contenido de la caja

Uber PA

Cable de alimentación

Guía del usuario

Manual sobre la seguridad y garantía

Soporte

Para obtener la información más completa acerca de este product (los requisitos del sistema,

compatibilidad, etc) y registro del producto, visite altoprofessional.com.

Para soporte adicional del producto, visite altoprofessional.com/support.

Baterías recargables

Las baterías de plomo-ácido recargables son del mismo tipo que se usa en los automóviles.

Al igual que con la batería del vehículo, la forma en que se usa tiene una influencia significativa

en la duración de su vida útil. Con un uso y tratamiento correctos, una batería de plomo-ácido

puede durar varios años. He aquí algunas recomendaciones para prolongar la vida útil de la

batería interna.

Uso general Cargue completamente la batería antes de utilizando el altavoz.

Cargue la batería completamente después de cada uso.

Almacenamiento Para lograr la mayor longevidad del producto, no lo almacene a

temperaturas muy altas (superiores 32 °C / 90 °F) o muy frías (inferiores

a 0 °C / 32 °F).

Es aceptable dejar su sistema de sonido enchufado. No sobrecargará

la batería.

Si deja que el nivel de la batería baje y no la carga durante 6 meses,

puede perder permanentemente su capacidad.

Reparación Si la batería no se carga, póngase en contacto con Alto Professional en

altoprofessional.com.

Disposición final Lleve la unidad a un centro de reciclaje o deséchela de acuerdo a las

ordenanzas locales.

Precauciones importantes para la seguridad

Para tener en cuenta: Alto Professional e inMusic no son responsables del uso de sus

productos o el mal uso de esta información para cualquier propósito. Alto Professional e

inMusic no son responsables del mal uso de sus productos causados por la omisión del

cumplimiento de los procedimientos de inspección y mantenimiento. Para más información,

consulte también el manual de seguridad y garantía incluido.

Precaución: Para reducir el riesgo de shock eléctrico, no conecte el Uber a una toma

de corriente cuando la rejilla está desmontada.

Montaje en soporte

•Instale siempre los altavoces de acuerdo con los códigos de electricidad y construcción

aplicables.

•Instale el altavoz de acuerdo a su peso máximo. Compruebe las especificaciones de su

soporte o columna para asegurarse de que pueda soportar el peso del altavoz. Asimismo,

observe todas las precauciones para la seguridad especificadas por el fabricante.

•No monte varios altavoces en el mismo soporte o columna.

•Verifique siempre que el soporte o columna esté sobre una superficie plana, nivelada y

estable. Asimismo, extienda totalmente las patas de los soportes tipo trípode y asegúrese

de que las patas no representen un riesgo de tropiezo.

•Inspeccione el soporte (o columna y elementos de fijación asociados) antes de cada uso y

no utilice equipos con piezas desgastadas, dañadas o faltantes.

•Tenga siempre cuidado en condiciones de viento a la intemperie. Es posible que deba

colocar peso adicional (como bolsas de arena) en la base del soporte para mejorar la

estabilidad. No fije pancartas o elementos similares a ninguna parte del sistema de

altavoces. Tales agregados pueden funcionar como velas y hacer volcar el sistema.

•Salvo que tenga confianza de que puede manejar el peso del altavoz, solicite a otra

persona que le ayude a levantarlo para colocarlo en el soporte o columna.

•Asegúrese de que los cables estén fuera del camino de los intérpretes, personal de

producción y audiencia, de modo que no tropiecen con ellos y hagan caer el altavoz del

soporte o columna.

Nivel de sonido

La exposición a niveles muy altos de ruido

puede causar pérdidas auditivas

permanentes. La Administración de

Seguridad y Salud Ocupacional de EE.UU.

(OSHA) ha especificado los niveles de

exposición permisibles a ciertos niveles de

ruido. Según la OSHA, la exposición a

niveles de presión sonora (SPL) elevados

que excedan estos límites puede causar

pérdidas auditivas. Cuando utilice equipos

capaces de generar SPL elevados, use

protecciones auditivas mientras dichos

equipos están en funcionamiento.

Horas diarias SPL (dB)Ejemplo

8 90 Música de bajo volumen

6 92 Tren

4 95 Tren subterráneo

3 97 Monitores de escritorio de

alto nivel

2 100 Concierto de música clásica

1,5 102 Remachadora

1 105 Máquina fabril

0,5 110 Aeropuerto

0,25 o menos 115 Concierto de rock

Instalación

1. Asegúrese de que todos los artículos indicados en Contenido de la caja estén incluidos

en ella.

2. Lea el manual sobre la seguridad y la garantía antes de utilizar el producto.

3. Para asegurar una máxima vida útil de la batería, asegúrese de que esté completamente

cargada antes de utilizarla por primera vez.

4. Asegúrese de que el volumen maestro del Uber esté en cero.

5. Encienda el Uber.

6. Conecte sus dispositivos.

7. Encienda todo en el siguiente orden:

•fuentes de entrada de audio (por ejemplo, micrófonos, instrumentos, reproductores de

CD/MP3)

•Uber PA

8. Suba el volumen hasta un nivel confortable.

9. Regrese el volumen maestro a cero y apague el Uber cuando no lo use.

Ejemplo

Los elementos que no se enumeran en Introducción >Contenido de la caja se venden por separado.

Dispositivo Bluetooth

Micrófono

Tableta,

reproductor

de MP3, etc.

Guitarra

Suministro

eléctrico

Inhaltsverzeichnis

Sprachen:

Andere Alto Professional Sprecher Handbücher

Alto Professional

Alto Professional MIXPACK 10 Bedienungsanleitung

Alto Professional

Alto Professional MIXPACK PRO Bedienungsanleitung

Alto Professional

Alto Professional BLACK 12 Bedienungsanleitung

Alto Professional

Alto Professional TX10 Bedienungsanleitung

Alto Professional

Alto Professional TX12 Bedienungsanleitung

Alto Professional

Alto Professional TRUESONIC TS112A Bedienungsanleitung

Alto Professional

Alto Professional TRUESONIC TS110A Bedienungsanleitung

Alto Professional

Alto Professional TX12 Bedienungsanleitung

Alto Professional

Alto Professional SXA28P Bedienungsanleitung

Alto Professional

Alto Professional MIXPACK EXPRESS Bedienungsanleitung

Alto Professional

Alto Professional TS2 Series Bedienungsanleitung

Alto Professional

Alto Professional TX208 Bedienungsanleitung

Alto Professional

Alto Professional TS212W Bedienungsanleitung

Alto Professional

Alto Professional TS308 Bedienungsanleitung

Alto Professional

Alto Professional TX308 Bedienungsanleitung

Alto Professional

Alto Professional TRUESONIC TS112 Bedienungsanleitung

Alto Professional

Alto Professional BLACK 10 Bedienungsanleitung

Alto Professional

Alto Professional Transport 12 Bedienungsanleitung

Alto Professional

Alto Professional TS408 Bedienungsanleitung

Alto Professional

Alto Professional TRUESONIC TS115W Bedienungsanleitung

Alto Professional

Alto Professional TOURMAX SX112 Bedienungsanleitung

Alto Professional

Alto Professional TS210 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung