Altos T110 F5 Bedienungsanleitung

Altos BrainSphere

T110 F5

User Guide

System setup

System notes

Thank you for purchasing yourAltos server. This user guide is intended as a reference for

experienced server technicians and helps detail many of the features available in Altos

servers. For more detailed information about any particular component or software solution,

you may consult the technical specifications or the user manual for that application.

Note: Before opening or removing any components

please contact your local certified Altos service

representative

Warning: Any parts or components damaged

during replacement by a non-certified technician

are not covered by the warranty. For details,

please consult the warranty guide from your system.

System component identification

Altos BrainSphere T110 F5 Front configuration:

Description

USB 3.2 Gen1 port x 2

USB 2.0 port x 2

Power Button

DVD CD-ROM (Optional)

Altos BrainSphere T110 F5 Rear configuration:

Description

Power Cord Connector

Power On/Off Button

COM port

USB 2.0 port x 2

USB 3.2 Gen1 port x 2

RJ-45 IPMI Dedicated port

RJ-45 GbE port x 2

VGA port

Setting up the system

Pre-installation requirements

Selecting a site

Before unpacking and installing the system, select a suitable site for the system for

maximum efficiency. Consider the following factors when choosing a site for the system:

Near a grounded power outlet.

Clean and dust-free

Stable surface free from vibration.

Well-ventilated and away from sources of heat.

Secluded from electromagnetic fields produced by electrical devices such as air

conditioners, radio and TV transmitters, etc.

Checking the package contents

Check the following items from the package:

System unit

Accessory box

If any of the above items is damaged or missing, contact your dealer immediately.

Save the boxes and packing materials for future use.

Turning on the system

After making sure that you have properly set up the system, applied power and connected

all the necessary peripherals, you can now power on the system. Follow the procedure

below.

Press the power button 。

The system starts up and displays a welcome message on the monitor. After that, a series

of power-on self-test (POST) messages appears. The POST messages indicate if the

system is running well or not.

Note: If the system does not turn on or boot after

pressing the power button, go to the next section

for the possible causes of the boot failure

Aside from the POST messages, you can determine if the system is in good condition by

checking if the following occurred.

The power status indicator on the front panel lights up blue.

The Num Lock, Caps Lock and Scroll Lock indicators on the keyboard light up.

Power-on problems

If the system fails to boot after you have applied power, check the following factors that

might have caused the boot failure.

The external power cord may be loosely connected.

Check the power cord connection from the power outlet to the power cord socket on

the rear panel. Make sure that the cord is properly connected to the power outlet and to

the power cord socket.

No power comes from the grounded power outlet. Have an electrician check your

power outlet.

Loose or improperly connected internal power cables.

Check the internal cable connections. If you are not confident to perform this step, ask

a qualified technician to assist you.

Warning! Make sure all power cords are

disconnected from the electrical outlet before

performing this task.

Note: If you have gone through the preceding

actions and the system still fails to boot, ask your

dealer or a qualified technician for assistance.

Turning off the system

There are two ways to turn off the server—via software or via hardware. The software

procedure below applies to a system running on a Windows OS. For other shutdown

procedures, refer to the related user documentation.

To turn off the system via software:

1. Press <Ctrl> + <Alt> + <Delete> on the attached keyboard or click Start on the

Windows taskbar.

2. Select Shut Down.

3. Select Shut Down from the drop-down menu, then click OK.

To turn off the system via hardware

If you cannot shut down the server via software, press the power button for at least four

seconds. Quickly pressing the button may put the server in a Suspend mode only.

System troubleshooting

Resetting the system

Before going through in-depth troubleshooting, attempt first to reset the system using one

of the methods below.

Perform

Purpose

To do this

Soft boot

To clear the system memory and

reload the operating system.

Press <Ctrl> + <Alt> + <Del>

Cold boot

To clear the system memory, restart

POST, and reload the operating

system. This will halt power to all

peripherals.

Turn the system off and then on

again.

Initial system startup problems

Problems that occur at initial system startup are usually caused by an incorrect installation

or configuration. Hardware failure is a less possible cause. If the problem you are

experiencing is with a specific application.

Initial troubleshooting checklist

AC power is available at the wall outlet?

Is the power supply module properly installed?

Is the system power cord properly plugged into the power supply module socket? and

connected to a NEMA 5-15R outlet for 100-120 V or a NEMA 6-15R outlet for 200-240

Are all peripheral cables correctly connected and secured?

Did you press the system power button to turn the server on (power on indicator should

be lit green)?

Are all device drivers properly installed?

Are hard disk drive(s) properly formatted and configured?

Are the BIOS configuration settings in the BIOS Setup Utility correct?

Is the operating system properly loaded?

Refer to the operating system documentation.

Are all hardware components compliant with the tested components

lists?

Are all internal cables correctly connected and secured?

Is the processor properly seated in its mainboard socket?

Are all standoffs in the proper location and not touching any components, causing a

potential short?

Are all add-in expansion cards fully seated in their mainboard slots?

Are all system jumpers correctly set?

Are all switch settings on add-in boards and peripheral devices correct?

To check these settings, refer to the manufacturer’s documentation that comes with

them. If applicable, ensure that there are no conflicts (e.g., two add-in boards sharing

the same interrupt).

Hardware diagnostic testing

This section provides a detailed approach to identifying a hardware problem and its cause.

Checking the boot-up status

Caution: Before disconnecting any peripheral cables

from the server, turn off the system and any

peripheral devices. Failure to do so can cause

permanent damage to the system and/or the

peripheral device.

1. Turn off the system and all external peripheral devices.

2. Disconnect all peripheral devices from the system, except for the keyboard and the

display monitor.

3. Make sure the system power cord is plugged into a properly grounded AC outlet and in

the power supply module cord socket.

4. Make sure the display monitor and keyboard are correctly connected to the system.

5. Turn on the display monitor.

6. Set the display brightness and contrast controls to at least two thirds of their maximum

range.

Refer the documentation that came with your display monitor.

7. If the operating system normally loads from the hard drive, make sure there is no

diskette in floppy drive and no disc in the optical drive.

8. If the power indicator is lit, attempt to boot from a disc.

9. Turn on the system.

Verifying the condition of the storage devices

As POST determines the system configuration, it tests for the presence of each mass

storage device installed in the system.As each device is checked, its activity indicator

should turn blue briefly. Check the activity indicators for the hard drive(s), DVD-ROM drive,

and any other 5.25" device you may have installed.

If any of these indicators fail to light up, refer to related problems listed in the Specific

problems and corrective actions section.

Inhaltsverzeichnis

Andere Altos Server Handbücher

Altos

Altos R380 F5 Bedienungsanleitung

Altos

Altos BrainSphere T350 F4 Bedienungsanleitung

Altos

Altos BrainSphere R385 F5 Bedienungsanleitung

Altos

Altos BrainSphere R185 F5 Bedienungsanleitung

Altos

Altos BrainSphere R369 F4 Bedienungsanleitung

Altos

Altos BrainSphere R365 F4 Bedienungsanleitung

Altos

Altos R360 F5 SFF Bedienungsanleitung

Altos

Altos BrainSphere R680 F4 Bedienungsanleitung

Altos

Altos Altos BrainSphere R365 F5 Bedienungsanleitung

Altos

Altos R320 F5 Bedienungsanleitung

Altos

Altos BrainSphere R385 F4 Bedienungsanleitung

Altos

Altos BrainSphere R580 F4 Bedienungsanleitung

Altos

Altos BrainSphere R685 F5 Bedienungsanleitung

Altos

Altos BrainSphere P530 F4 Bedienungsanleitung

Altos

Altos BrainSphere T310 F5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung