Altronix TROVE DMP 734 Bedienungsanleitung
T1DMK3F4
4 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove1 enclosure with TDM1 Altronix/DMP backplane
- One (1) eFlow6NB - Power Supply/Charger
- One (1) VR6 - Voltage Regulator
- One (1) PDS8 - Dual Input Fused Power Distribution Module
T2DMK7F8
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove2 enclosure with TDM2 Altronix/DMP backplane
- One (1) eFlow104NB - Power Supply/Charger
- One (1) ACM8 - Fused Access Power Controller
- One (1) VR6 - Voltage Regulator
- One (1) PDS8 - Dual Input Fused Power Distribution Module
T1DMK3F4D
4 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove1 enclosure with TDM1 Altronix/DMP backplane
- One (1) eFlow6NB - Power Supply/Charger
- One (1) VR6 - Voltage Regulator
- One (1) PDS8CB - Dual Input PTC Power Distribution Module
T2DMK7F8D
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TDM2 Altronix/DMP backplane
- One (1) eFlow104NB - Power Supply/Charger
- One (1) ACM8CB - PTC Access Power Controller
- One (1) VR6 - Voltage Regulator
- One (1) PDS8CB - Dual Input PTC Power Distribution Module
Access & Power Integration
Altronix/DMP 734/734N Wiegand Kits
Models Include:
Rev. TDMK_022521
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
- 2 - Trove DMP Kits Installation Guide
Overview:
Altronix T1DMK3F4(D) and T2DMK7F8(D) Trove DMP kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed
Altronix power supply/chargers and sub-assemblies.
T1DMK3F4(D) accommodates up to four (4) DMP 734/734N Wiegand modules for up to four (4) doors in a single enclosure.
T2DMK7F8(D) accommodates up to eight (8) DMP 734/734N Wiegand modules for up to eight (8) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
Power Supply Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
120VAC 60Hz
Input Current (A)
Maximum Supply
Current for Main
and Aux. Outputs on
Power Supply board
and ACM8(CB) Access
Power Controllers’
outputs
Nominal DC
Output Voltage
Fail-Safe/Fail-Secure or
Dry Form “C” Outputs
Additional Fused
Outputs
ACM8(CB) Board
Input Fuse Rating
ACM8 Board
Output Fuse Rating
ACM8CB Board
Output PTC Rating
PDS8 Board
Input Fuse Rating
PDS8 Board
Output Fuse Rating
PDS8CB Board
Input PTC Rating
PDS8CB Board
Output PTC Rating
[DC] [Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T1DMK3F4 5A/
250V
10A/
32V 3.5 24VDC @ 6A
20.17-
26.4
20.28-
26.4
–
8
–––
10A/
32V
3A/
32V – –
T1DMK3F4D – 9A 2A
T2DMK7F8 6.3A/
250V
15A/
32V 4.5 24VDC @ 9.4A 810A/
250V
2.5A/
250V –10A/
32V
3A/
32V – –
T2DMK7F8D – 2.5A – – 9A 2A
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top two/three keyholes in the enclosure. Install two/three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two/three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired
location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure
approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the
Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount DMP 734/734N Wiegand modules to backplane, refer to pages 3, 4.
5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB,
eFlow104NB and corresponding Sub-Assembly Installation Guides for ACM8(CB),
PDS8(CB) and VR6 for further installation instructions.
Hardware:
Nylon Spacer | 5/16” Pan Head Screw | Lock Nut
Fig. 1
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Trove DMP Kits Installation Guide - 3 -
T1DMK3F4(D): Configuration of DMP 734/734N Wiegand Modules:
1. Fasten spacers (provided) to pems that match the hole pattern for DMP Wiegand Modules (Fig. 2, pg. 3).
2. Mount DMP 734/734N modules into the correct positions (Fig. 2, pg. 3):
a. Remove DMP 734/734N board from the plastic housing. Use the base part of the housing to mount onto TDM1 (Fig. 2a, 2b, pg. 3).
b. Secure the base of DMP 734/734N to the spacers using provided 5/16” pan head screws.
c. Make all necessary connections before reassembling DMP 734/734N Wiegland modules.
3. Fasten TDM1 backplane to Trove1 enclosure utilizing hardware (provided).
NC C NO NC C NO
AC FAIL BATFAIL
TRIGGER
AC DCAC1
EOL NO GND
SUPERVISED RESET
+AUX-
- BAT +-DC +
L G N
OFF - 24V
ON - 12V
ON
Altronix - eFlow6NB
+ INP1 --
DM1 +OFF
IN1
IN2DM1 +
DM2 +
DM2 +
Common (--- )
Common (--- )
+ INP2 --
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Altronix
PDS8(CB)
Altronix VR6 is mounted under PDS8(CB)
DMP 734 or 734N
Wiegand
DMP 734 or 734N
Wiegand
DMP 734 or 734N
Wiegand
DMP 734 or 734N
Wiegand
Spacer
DMP 734 plastic housing
Backplane
Pan Head
Screw
Pem Mounting
Spacer
Placement
Fig. 2bFig. 2a
Fig. 2 - T1DMK3F4(D) Configuration
- 4 - Trove DMP Kits Installation Guide
T2DMK7F8(D): Configuration of DMP 734/734N Wiegand Modules:
1. Fasten spacers (provided) to pems that match the hole pattern for DMP 734/734N Wiegand Modules (Fig. 3, pg. 4).
2. Mount DMP 734/734N modules into the correct positions (Fig. 3, pg. 4):
a. Remove DMP 734/734N board from the plastic housing. Use the base part of the housing to mount onto TDM2 (Fig. 3a, 3b, pg. 4).
b. Secure the base of DMP 734/734N to the spacers using provided 5/16” pan head screws.
c. Make all necessary connections before reassembling DMP 734/734N Wiegland modules.
3. Fasten TDM2 backplane to Trove2 enclosure utilizing hardware (provided).
Altronix - eFlow104NB
– DC +– BAT +
L G N
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix ACM8(CB)
+ INP1 --
PWR1 +
PWR1 +
OFF
IN1
IN2
PWR2 +PWR2 +
COM ---
COM ---
+ INP2 --
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Altronix PDS8(CB)
Altronix VR6 is mounted under PDS8(CB)
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
DMP 734
or 734N
Wiegand
Spacer
DMP 734 plastic housing
Backplane
Pan Head
Screw
Pem Mounting
Spacer
Placement
Fig. 3bFig. 3a
Fig. 3 - T2DMK7F8(D): Configuration
Trove DMP Kits Installation Guide - 5 -
Notes:
- 6 - Trove DMP Kits Installation Guide
eFlow Power Supply/Chargers can be Controlled and Monitored while
Reporting Power/Diagnostics from Anywhere over the Network...
LINQ2 Mounts Inside any Trove Enclosure
LINQ2 - Network Communication Module
LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up
and running at optimal levels. It facilitates fast and easy installation and set-up, minimizes system downtime,
and eliminates unnecessary service calls, which helps reduce Total Cost of Ownership (TCO) - as well as creat-
ing a new source of Recurring Monthly Revenue (RMR).
LINQ2
Features:
- UL Listed in the U.S. and Canada.
- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.
- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change,
output state change and unit temperature.
- Access control and user managment: Restrict read/write, Restrict users to specific resources
- Two (2) integral network controlled Form “C” Relays.
- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.
- Email and Windows Dashboard notifications
- Event log tracks history.
- Secure Socket Layer (SSL).
- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.
LINQ2 Module
Altronix eFlow
Power Supply
Network Connection:
Installation, Programming
and Monitoring
Trove DMP Kits Installation Guide - 7 -
T1DMK3F4 Enclosure Dimensions (H x W x D approximate):
18” x 14.5” x 4.625” (457mm x 368mm x 118mm)
4.5” (114.3mm) 4.5” (114.3mm) 2.75”
(69.9mm)
1.115” (28.3mm)
1.36” (34.5mm)
1.25” (31.8mm) 1.25” (31.8mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
4.5” (114.3mm)
13.0” (330.2mm)
0.6” (15.2mm)
14.5” (321.3mm)
1.45” (36.8mm)
7.25” (184.2mm)
1.95” (49.5mm)
1.1” (27.9mm)
0.6” (15.2mm)
0.57” (14.5mm)
18.0” (457.2mm)
1.25” (31.8mm)
- 8 - Trove DMP Kits Installation Guide
T2DMK7F8 Enclosure Dimensions (H x W x D):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm)
6.75” (171.5mm)8.25” (209.5mm)
8.00” (203.2mm)
2.00” (50.8mm)
2.00” (50.8mm)
1.25” (31.8mm)
1.25” (31.8mm)
5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)
1.25” (31.8mm)
6.25” (158.8mm) 19.80” (502.9mm)
1.00” (25.4mm)
27” (685.8mm)
1.5”
(38.1mm)
2.00” (50.8mm) 2.00” (50.8mm)
3.5”(88.9mm) 3.5”(88.9mm)
21.50” (546.1mm)
5.25” (133.35mm) 5.25” (133.35mm)
6.25” (158.8mm)
1.25”
(31.8mm)
0.85” (21.6mm)
0.5625” (14.3mm)
2.415” (61.3mm)
0.685” (17.4mm)
1.77”
(45mm)
0.885” (22.5mm)
1.125” (28.3mm)
Knockouts
2.00” (50.8mm) 2.00” (50.8mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
IITrove DMP Kits I27U MEMBER
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Altronix Stromversorgung Handbücher
Altronix
Altronix SMP3CTX Series Bedienungsanleitung
Altronix
Altronix TROVE TC1 Bedienungsanleitung
Altronix
Altronix AL175220 Series Bedienungsanleitung
Altronix
Altronix eFlow3N Bedienungsanleitung
Altronix
Altronix R248UL Series Bedienungsanleitung
Altronix
Altronix SMP5CTX Series Bedienungsanleitung
Altronix
Altronix WayPoint DC Series Bedienungsanleitung
Altronix
Altronix AL600ULXD Bedienungsanleitung
Altronix
Altronix ALTV1224DC220 Series Bedienungsanleitung
Altronix
Altronix ALTV1224DC Series Bedienungsanleitung
Altronix
Altronix SMP10 Bedienungsanleitung
Altronix
Altronix LPS3C24X Bedienungsanleitung
Altronix
Altronix AL300ULXB2 Bedienungsanleitung
Altronix
Altronix TROVE T1RAL3F8 Bedienungsanleitung
Altronix
Altronix R248ULi Bedienungsanleitung
Altronix
Altronix AL300XB2V Bedienungsanleitung
Altronix
Altronix OLS250 Bedienungsanleitung
Altronix
Altronix AL600X220 Series Bedienungsanleitung
Altronix
Altronix VertiLine563 Bedienungsanleitung
Altronix
Altronix AL400UL3 Bedienungsanleitung
