Altwork TruVue Kurzanleitung zur Einrichtung
TruVue Assembly and Use
TruVue - VCS
Video Conferencing Station
Product Details:
Lighting solution and webcam mounting system designed to attach
tomost monitors with an integrated VESA mount including monitors
on Altwork Stations Includes:
Mounting frame and hardware:
•Attaches to monitors with standard 75x75 and 100x100 VESA
screw locations
•(4) M4 mounting screws for mounting to your Altwork Station of
other VESA mount
•Includes P2 screwdriver for assembly (No other tools required)
•Lighting system with 2 LED panels and manual reset/control switch
Light Panels
•Source type light: LED
•LED type: “2835”
•LED bulbs: 240 pcs (per panel)
•LED panel size 6-1/4” x 9”
•Dimmable from 0-100%
•Color temperature: 2700K-5700K
•Impute power: AC100-240 VAC 50/60 Hz
•Out power: 42W (per panel)
Lighting remote:
•Turns lights on/off (Separately or together)
•Adjusts brightness warm to cold (Separately or together)
•Adjusts light intensity (Separately or together)
•(2) AAA batteries (US only)
Webcam Mount:
•Designed to work for all standard webcams
•Webcam mounts with standard 1/4-20 screw or adhesive tape
(included)
•6” Webcam vertical travel from top of screen
•Retracts out of view above monitor
•Flips down for desk view
WARNING!
•The power cord plug should be firmly inserted in the socket, and the power plug
should be pulled out after use to prevent electric shock and fire. The lights can not be
controlled fully when the battery power of the remote control in insufficient. Please
replace remote battery in time.
•Do not pull out the plug by pulling the power cord. Be sure to hold the plug firmly and
pull out of the socket.
•Do not pinch or kink the power cord during adjustment of the lights.
•Do not use when the power cord is damaged, or the plug is worn.
•Don’t spray or wash the product with water, and do not place it in a wet and easily
splashed place, so as to avoid affecting the electrical insulation performance of the
product.
Packing List
1. Frame with Lights
2. VESA Mount Brackets
3. Slides
4. Camera Mount Assembly
5. Hardware Kit
6. Remote
5
4
3
1
6
2
Use M4 x 14MM screws to attach the bracket to the back
of the monitor to the VESA mount threads as shown.
(2) VESA Mount Brackets
(4) M4 x 14mm flat-head screws
TruVue - VCS
Attach Brackets to Monitor with VESA Mount
TruVue - VCS
Attach to Monitor with VESA Mount (Over Existing Mount)
Remove existing screws from
left side of monitor mount. Remove existing screws from
right side of monitor mount.
Use M4 x 20mm flathead screws
to mount the bracket to the back
of the monitor through the VESA
mount as shown.
Attach the right side bracket
(2) VESA Mount Brackets
(4) M4 x 20mm flat-head screws
(2) Slides
(4) M4 x 12mm pan-head screws
(4) Large washers
Use M4 x 12mm pan-head screws to attach Slides to
VESA Mount Brackets with screw countersink hole at
top facing out and notch facing the monitor as shown.
(Start with the slides all the way down on the screws)
TruVue - VCS
Attach Slides to VESA Mount Brackets
Use M4 x 10mm flat-head screws to attach the bar of
the Frame to the Slides as shown.
(1) TruVue Frame
(2) M4 x 10MM flat-head screws
TruVue - VCS
Attach Frame to Slides
Loosen (4) screws to slide the Frame up so
that the bar is parallel to and just above the top
of the monitor as shown, then re-tighten.
TruVue - VCS
Adjusting the Frame to top of Monitor
Use the M4 x 16mm pan-head screw and small washer to attach the
Camera Mount to the Frame.
Make sure to adjust the location far enough forward to avoid hitting the
screen with the Camera Mount when deployed.
(1) Camera Mount Assembly
(1) M4 x 16MM pan-head screw
(1) Small washer
TruVue - VCS
Attachment Camera Mount to VCS Frame
1. Remove (3) clamps from Camera Bar
2. Loosen both thumb screws
3. Remove Camera Bar from Slide Block
Note: Thumb nuts and plastic block may need to
be removed for larger connectors to be installed
through the block.
TruVue - VCS
Attaching Camera to VCS Mount
Picture of screws and foam
tape
(1) ¼-20 x 1/4”
(1) Alt ¼-20 x 3/8”
(1) Alt Adhesive Tape
1. If the camera has a ¼-20 thread
mounting option,
2. select the correct length screw 1/4”
or 3/8” from the Hardware Kit.
3. Attach the camera to the Mount
through the hole that allows the
camera full range of adjustment.
1. If the camera does not have a ¼-20 thread mounting option,
select the Adhesive Tape from the Hardware Kit.
2. Make sure the surface of the Camera and Mount are clean and
free of oils then apply Tape to the Camera Mount.
3. Attach the Camera to the Mount onto the tape in a location
that allows the camera full range of adjustment.
TruVue - VCS
Attaching Camera Mount
Andere Handbücher für TruVue
1
Inhaltsverzeichnis
Andere Altwork Konferenzsystem Handbücher
Beliebte Konferenzsystem Handbücher anderer Marken
Kramer
Kramer VIA GO Bedienungsanleitung
AVT
AVT MAGIC AC1 Go Bedienungsanleitung
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung
Sony
Sony PCS-I150 Bedienungsanleitung
Middle Atlantic Products
Middle Atlantic Products VTC Series Bedienungsanleitung
Prentke Romich Company
Prentke Romich Company Vanguard Plus Leitfaden
