Amana ASD2620HRZ Bedienungsanleitung

m Side by Side

Form No. A/01/05 Part No. 12842114 w_vw.amal_a.com Utha U.S.A. :¢2005 Maytag Appliances Sales Co.

What Nee to }( ow Abo t

Safety str ctio s

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground} prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

SAVE THESE l NSTRUCTIONS

Do not install refrigerator near oven, radiator or other

heat source. Wfnot possible, shield refrigerator with

cabinet material.

Do not install where temperature falls below 55° F

(13° C} or rises above 110° F (43° C}. Malfunction

may occur at this temperature.

Refrigerator is designed for indoor househomd

appmication onmy.

Measuring the Opening

When installing your refrigerator, allow '/_"space at top

and '%'space behind machine compartment cover

(located in the tea0 for proper air circuhtion. If the

refrigerator is placed with the door hinge side against

a wall, you may want to allow additional space so the

door can be opened wider.

Subfiooring or floor coverings (i.e. carpet, tile, wood

floors, rugs} may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

UMPORTANT: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Phgging

refrigerator in immediately may cause damage to

internal parts.

Use an appliance doily when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its fronL

Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening

restraints may dent or damage outside finish.

Door and Hinge Removam

Some installations require door removal to get

refrigerator to final location.

1. Unplug power cord from power source°

2. Remove toe grille and bottom bracket covers (see

page 7}.

Open both doors 180°, or as wide as possible.

it:or ice and water dispensing models only:

Remove the left side bracket cover by carefully

pulling the water line to pry the cover loose. Then

continue to maintain downward pressure to the

notched side of the cover while swinging it off

(see page 7}.

.For refrigerators in operation, shut off water before

removing water line from the door.

To Disconnect the Water Line:

Push in white collar (A} and hold.

Pull the door-side tube (B} from the connector.

To Reconnect the Water Line:

,Firmly push tube %" into the connector. Use

lines on the tube as a guide for full insertion.

.If tube end is damaged, cut off %" before

reconnecting.

If leaking occurs, reconnect the line.

3, Close doors.

/4, Remove top hinge covers by

removing Phillips screws.

5, Unscrew %_"hex head screws from

top hinges.

For water dispensing

models only:

Do not remove screw

connecting green ground

wire,

6. For ice and water dispensing models only:

Detach main wire connector harness and red wire

harness.

"To detach main wire

harness, use a fiat blade

tool or fingernail to press

junction point between two .......

connectors to release.

,To detach red wire harness, press

tab on underside of connector to

release.

7. Remove top hinges along with doors.

Repmacing the Doors

To replace the doors, follow the steps in Door and

Hinge Removal in reverse order.

UMPORTANT: If water line tube end is damaged, cut

off 5%,before reconnecting.

Connecting the Water Supply

(select models}

8. Remove bottom hinges with a _" hex head driver.

MateriaRs Needed

. ¼" outer diameter flexible copper tubing

. Shut-off valve (requires a '/4"hole to be drilled into

water supply line before valve attachmen0

. Adjustable wrench

. '/_"hex nut driver

. Add 8' to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2' diamete0.

Avoid kinks in the copper tubing

when bending the service loop.

2. Remove plastic cap from water valve

inlet porL

3_ Place brass nut (A} and

sleeve (B} on copper

tube end as illustrated,

(Do not use old sleeve.}

4_ Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

UMPORTANT: Do not overtighten. Cross

threading may occur`

.Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C} and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 24 hours.

Correct leaks, if necessary.

Handme installation

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator,

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Front Mount Handle

Materials Needed

Gloves to protect hands

• Phillips screwdriver

• Plastic door removal card (or %" thick plastic card},

retain the card

To UnstaH:

The handles are to be oriented

as shown.

Align front mount door handle

clip with the door tabs.

Ensure the handle clips are

positioned slightly above the

door tabs.

Door

Tab

4. Rotate the handle so that the

handle is flat against the door.

5. Push the handle down against the

upper door tab just enough to allow

it to hang unsupported.

6.Alignbottomof handlewithlower

doortab.Pressupperhandleendto

doorsurfaceandfirmlygrasplower

endofhandle.Gentlyslidehandle

upwarduntilbottomofhandlesettles

ondoorsurface,thenreverse

direction,slidingdownwardto almost

engagingtabwithclip.

7.Graspthehandlefirmlyandslide

downuntilitclicks.Theaudibleclick

indicatesfasteningclipsaresecurely

interlocked.

To Remove:

1. Flex the handle away from the door

panel. Simultaneously place door

handle removal card underneath

the base of the lower handle. Insert

the card to the line or until it stops.

2. Grasp the lower part of the handle

firmly and lift to remove.

Handle Extensions (select models)

To UnstaH:

1. Align and clip handle extension into position on the

handle. Press the extension over the door retainers.

To Remove:

1. Slide the extension down and unclip from door

retainer.

Full-Length Aluminum Handles

To Install:

1. Release top door trim by removing

Phillips screws from top of fresh food

door and retain screws for later use.

Align notches on back of handle with

retaining clips on doors. Insert

clips into notches and slide

handle down until it contacts

bottom trim.

3, Replace top door trim and Phillips

screws,

4,Repeat instructions 1-3 to install

other handle.

To Remove:

1. Release top door trim by removing

Phillips screws from top of fresh food

door and retain screws for later use.

2. Grasp handle firmly with both hands.

Slide handle upward approximately

-_//'to release.

3.Repeat instructions 1-3 to

remove other handle.

To fleinstaiI:

1. Repeat in reverse order.

Toenhancetheappearanceandmaintainperformance

therefrigeratorshouldbelevelin accordancewiththe

followinginstructions.

Note

,Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed

,_X,"hex head driver

,Carpenter's level

1. Remove toe grille.

,Grasp firmly and pull bottom

outward to unclip.

2. Remove bottom bracket cover(s}.

,Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

, Use slight pressure to pry the

cover loose.

Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

3. Using hex head driver, turn front adjustment

screws (A} clockwise to raise and counterclockwise

to lower the front of the refrigerator.

Some models only have adjustment screws "A_"

Select models also have rear adjustment screws

(B}. Using the hex head driver, turn each of these

adjustment screws (B} to raise or lower the rear of

the refrigerator.

Using the carpenter's level, make sure front of

refrigerator is '/4"(6 ram} or K bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

If required, correct rocking of refrigerator by

turning rear adjustment screw clockwise to raise

rocking corneE If doors are uneven, do the

following:

Determine which

door needs to be

raised.

Turn front roller

adjustment screw (A}

clockwise to raise

front corner of door.

If one refrigerator door has reached the limit of

its adjustment range and doors are still not level,

raise or lower the opposite door by turning roller

adjustment screw counterclockwise.

Check with level to verify '/9"tilt to the back for

proper door closure.

If refrigerator is aligned and stable, replace toe

grille and hinge covers.

Z Replace bracket cover(s}.

Position cover into the outer edge of the hinge.

Swing the cover toward the cabinet and snap it

into place.

8. Replace the toe grille.

,For proper reinstalhtion, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

.Align the toe grille mounting clips with the lower

cabinet slots.

,Push the toe grille firmly until it snaps into place.

Dial Temperature Controls

(select models)

The controls are located at the back left of the

refrigerator compartment.

*The freezer control turns the cooling system on.

Neither section will cool if freezer control is set to

OFF,

initial Control Settings

After plugging the refrigerator in,

set the controls.

*To adjust the controls, turn the

control knob to the left or right

as desired.

*Set the freezer control on 4.

*Set the refrigerator control on 4.

*Let the refrigerator run at least 8

to 12 hours before adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 21

for instructions on checking compartment

temperature.

*Except when starting the refrigerator, do not change

either control more than one number at a time.

*Allow 2/4hours for temperatures to stabilize.

*Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm Turn the refrigerator control

to next higher numben

Refrigerator too cold Turn the refrigerator control

to next lower number,

Freezer too warm Turn the freezer control to

next higher number,

Freezer too cold Turn the freezer control to

next lower number,

Turn refrigerator OFF Turn the freezer control to

OFF.

* Turning freezer control to OFF stops cooling in

both compartments. It does not shut off power to

the refrigerator`

Touch Temperature Controls

(select models, style varies by model)

The controls are located at the top front of the

refrigerator compartment.

Contro[

_!!iii}ii, Freezed

[initial Centre[ Settings

After phgging tile refrigerator in, set the controls.

,Pressing the 1_i, or pads adjusts the controls to

the desired setting.

,Set the freezer control on/4.

,Set the refrigerator control on/4_

Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabineL This condition wiI[ be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

2/4 hours after adding food, you may decide that one

or both compartments should be colder or warmen If

so, adjust the control(s} as indicated in the

Temperature Control Guide table below. See page 21

for instructions on checking compartment

temperature.

,Except when starting the refrigerator, do not change

either control more than one number at a time.

Allow 2/4hours for temperatures to stabilize.

Temperature Control Guide

Refrigerator too warm Set the refrigerator control

to next higher number by

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OF[:

Set the refrigerator control

[to next lower number by

Set the freezer contro[ to

[Set the freezer control to

next lower number by

Press the freezer or

[refrigerator :_ pad until a

dash "-" appears in the

display.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Amana Kühlschrank Handbücher

Amana

Amana SBDE522VW Bedienungsanleitung

Amana

Amana ARS266 Bedienungsanleitung

Amana

Amana W10316638A Bedienungsanleitung

Amana

Amana AMA27BK Bedienungsanleitung

Amana

Amana BX22S5W Bedienungsanleitung

Amana

Amana ABB2222FED1 Fehlerbehebungshandbuch

Amana

Amana ARB2217CW Bedienungsanleitung

Amana

Amana ABR2222FES Stücklistenhandbuch

Amana

Amana Top Freezer Bedienungsanleitung

Amana

Amana REFRIGERATOR Bedienungsanleitung

Amana

Amana TM16Q Bedienungsanleitung

Amana

Amana ASD2575BR Montageanleitung

Amana

Amana A9RXNMFWS Bedienungsanleitung

Amana

Amana ABB1921WE Bedienungsanleitung

Amana

Amana AFB2234WES2 Bedienungsanleitung

Amana

Amana W10175445A Bedienungsanleitung

Amana

Amana Side By Side Refrigerator Bedienungsanleitung

Amana

Amana AFD2535DEB Stücklistenhandbuch

Amana

Amana Side By Side Refrigerator Bedienungsanleitung

Amana

Amana AFD2535FES12 Fehlerbehebungshandbuch

Amana

Amana TX21A3W-P1181504WW Bedienungsanleitung

Amana

Amana Bottom-Freezer Refrigerator Bedienungsanleitung

Amana

Amana ABL2227FES12 Bedienungsanleitung

Amana

Amana Side-by-Side Refrigerator Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung