AMAREW AM Series Bedienungsanleitung

EMPOWERS YOU

Thank you for choosing our AM-series.

www.amarew.com

Battery indicator

Extendable tiller

Cable clamps

Angle adjustment lever

Battery cable

Fin

Figure A

Depth adjustment screw

Transom mounting screws

Propeller

Counter force bolt

Control box

AMAREW® AM-series product manual

p.4

p. 5

p. 6

p. 7

p. 8

p. 9

p. 10

p. 11

p. 12

General information

Safety information

Wiring and battery recommendation

First time running

Propeller installment

Fin installment

Tiller handle installment

Usage instructions

Attaching the motor to your boat

Depth and steering adjustment

Connecting a battery

Battery indicator

Speed control

Replacing the propeller

Maintanance

Storage

Technical data

Warranty

Table of contents

AMAREW® AM-series product manual

Congratulations! And thank you for choosing an AMAREW® electric outboard motor.

We hope you will love using it. AMAREW® Electric outboard motors are designed and

developed by our specialized engineering team. After years of effort, we have succeeded

in producing superior electric outboard motor series that ﬁt various customers’

requirements and provide a high level user experience.

Please read and retain this manual before using your motor. This manual contains

information that describes the procedures for a safe operation and the daily

maintenance of your electric outboard motor. A safe operation will prevent personal

injuries and product damage.

Do not allow children (<18 years old) to operate the electric outboard motor. Do not

modify the unit in any way or add accessories that are not intended for this product.

Never fully submerse the unit. If the unit is accidentally submersed, disconnect the

battery(ies) and leave it to dry.

Warning: Always disconnect the power cables from the motor when replacing the

propeller, removing debris around the propeller, charging the battery(ies), transporting

the boat or when the motor is not in use.

For AM-series motors up to 66LBS, AMAREW® recommends to use a 12 volt deep cycle

marine battery. For AM-series motors with a thrust over 66LBS, the deep cycle marine

battery should be 24 volt. Each battery should at least have an 50 ampere rating or

higher. To extend running time an additional battery could also be used.

Warning: Be sure that the speed control handle is in the zero (“0”) position before

connecting to the battery(ies), as a rotating propeller can cause personal injury.

General information

Safety information

Wiring and battery recommendation

AMAREW® AM-series product manual

Propeller installment:

Make sure the propeller and the pin are aligned correctly. Otherwise the propeller

cannot be properly ﬁxed. Place the propeller, washer and knob respectively. Then hold

the propeller with one hand and tighten the knob with your other hand, by turning it

clockwise (see ﬁgure B).

Warning: Always disconnect the power when installing the propeller. Watch out for the

sharp edges of the propeller during the installation.

Fin installment:

Take the plastic ﬁn out of the accessory box (see ﬁgure C). Disconnect the screws and

ﬁnd the screw holes on the bottom side of the lower unit. Keep the ﬁn and screw holes

aligned. Then insert and tighten the screws with a wrench or spanner. Make sure the

screws are properly tightened to prevent the ﬁn from loosening.

First time running

Figure B

Figure C

AMAREW® AM-series product manual

Tiller handle installment:

Find the sticker securing the marble on the aluminum pipe and carefully tear it off. Keep

the tiller handle aligned with the aluminum pipe. Adjust the direction in accordance

with the plastic part on top of the aluminum pipe (see ﬁgure D). Adjust the angle to push

the aluminum pipe in to the handle. Lightly press down the marble to get it through the

handle. Once you hear the “click” and the handle is pushed to the end, the handle is fully

in place.

Warning: This is a one-way installment. Once installed, do NOT attempt to pull out the

handle again, since the controls could be damaged.

Attaching the motor to your boat:

Attach the motor to the stern of the boat and tighten the two transom mounting screws

securely while taking care not to over tighten. To adjust the angle of the motor after you

attached it to the stern of the boat, hold the motor head with one hand and press the

angle adjustment lever with your other hand (see ﬁgures A and E). Press and hold the

angle adjustment lever until the desired angle has been reached. You can now release

the lever while ensuring the mechanism locks securely.

Warning: When adjusting the angle of the electric outboard motor, make sure the area

between the shaft and the hull of the boat is clear, as you might get injured. When

mounting or detaching the electric outboard motor, make sure that the battery is

disconnected.

Usage instructions

Figure D

AMAREW® AM-series product manual

Depth and steering adjustment:

Hold the motor shaft with one hand, loosen the depth adjustment screw and set the

motor to the desired depth. After the desires depth is reached, retighten the depth

adjustment screw securely. Adjust the steering force according to your needs by

loosening or tightening the counter force bolt (see ﬁgures A and E).

Warning: The motor can only be used in waters with a depth of at least 80 cm

Connecting a battery:

Before connecting the cable clamps to the battery terminals, ensure that the speed

control handle is in the zero (“0”) position and be sure to stand clear of the propeller.

Make sure that the battery terminals are clean, as a clean connection will minimize

power waste and extracts maximum power from the battery. If required, connect the

batteries in series ﬁrst.

Then connect the red cable to the positive (+) terminal and the black cable to the

negative (-) terminal (see ﬁgure F). You will see that the battery indicator has turned on.

The motor is now powered up.

Warning: Make sure to always have the speed control handle in the zero (“0”) position

before connecting the battery(ies), as a rotating propeller can cause personal injury.

Remember to always disconnect the motor from the battery(ies) before the motor

leaves the water, as a rotating propeller can cause personal injury.

Figure E

Counter froce bold

Depth

Adjustment

Screw

Angle adjustment lever

AMAREW® AM-series product manual

Battery indicator:

The battery indicator (see ﬁgure A) represents the actual battery voltage. The remaining

battery capacity depends on the type and the speciﬁcations of the battery that is

being used. Please refer to your battery speciﬁcations in order to obtain a thorough

understanding of the remaining power.

Warning: Make sure to test the range of your battery(ies) carefully, as the motor will

only have limited power once the battery(ies) is drained.

Speed control:

Make sure the speed control handle is in the zero (“0”) position. If you see that the battery

indicator is turned on, this means that the motor can be started any time. You can now

adjust the speed according to your wish, in ﬁve forward and three reverse speeds, by

turning the handle. Turn the handle clockwise to move forward and anticlockwise to

go backwards (see ﬁgure G). When you don’t want to move, set the handle back into

the zero (“0”) position. No power will be used in this setting. The telescopic tiller can be

extended up to 14cm, to accommodate your needs, simply by pulling out the handle.

Warning: Always disconnect the battery(ies) once the motor leaves the water, as a

rotating propeller can cause personal injury.

Figure F

Figure G

AMAREW® AM-series product manual

Hold the propeller blade and loosen the propeller knob. It can only be done counter

clockwise and manually, without tools. Pull the propeller straight off. If the propeller is

stuck, grasp one blade with one hand and tap lightly on the backside of the opposite

blade with a rubber mallet until the propeller comes off. If the propeller pin is bent or

broken, replace it. Align the new propeller with the propeller pin. Reinstall the propeller

knob and tighten it manually and clockwise (see ﬁgure B).

Warning: Make sure that the motor has been disconnected from the battery(ies) before

replacing the propeller. Do not strike the propeller pin with a hammer to remove the

pin. Damaging the motor in this way will not be covered by warranty.

1. Before each use, make sure to check the wiring. Check for loose connectors, wire rust,

scratches and cracks in the cables and connectors. Clean the connectors if they are

not 100% clean and replace the cables and connectors whenever necessary.

2. After each use, wash the engine thoroughly with fresh water. Especially after usage

in salt water.

3. Every month, add grease to all the moving parts in order to prevent corrosion.

4. When the propeller breaks, remove the propeller and replace the pin (see previous

next section).

Warning: A lack of maintenance on the wiring and connectors may cause the wiring

and connectors to overheat or even burn.

Warning: Remember to wash the motor with fresh water each time after it has been

used it in salt water, as it this greatly reduces the possibility of corrosion.

Replacing the propeller

Maintenance

AMAREW® AM-series product manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMAREW Außenbordmotor Handbücher

AMAREW

AMAREW XM180 Bedienungsanleitung

Beliebte Außenbordmotor Handbücher anderer Marken

Yamaha

Yamaha VF150 Bedienungsanleitung

Sleipner

Sleipner SEP-IP30 Bedienungsanleitung

Suzuki

Suzuki DF 40 Bedienungsanleitung

SELVA MARINE

SELVA MARINE Corse Bedienungsanleitung

TOHATSU

TOHATSU BFT 250A Bedienungsanleitung

KONRAD

KONRAD Series 600B Bedienungsanleitung

Mercury

Mercury 8 Bigfoot 4-Stroke Installationsanleitung

Sleipner

Sleipner E-Vision Electric Thruster E300 Bedienungsanleitung

Suzuki

Suzuki DF40A Bedienungsanleitung

IST

IST 18.BF200D Bedienungsanleitung

Side-Power

Side-Power SP 155 TC i Bedienungsanleitung

Mercury

Mercury 40 FourStroke Bedienungsanleitung

Quick

Quick BTR250 Bedienungsanleitung

Yamaha

Yamaha VF90 Bedienungsanleitung

Yamaha

Yamaha D150H Bedienungsanleitung

Yanmar

Yanmar ZT350 series Bedienungsanleitung

MotorGuide

MotorGuide X3-40 Bedienungsanleitung

Mercury

Mercury 30 - 60 HP Bedienungsanleitung